DeWalt D25123K manual

DeWalt D25123K
5.3 · 1
PDF manual
 · 144 pages
manualDeWalt D25123K




INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286(JUL10) Part No. N074431 Copyright © 2006, 2009 DEWALT D25123, D25213, D25313, D25223, D25323, D25324, D25330The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.If you have questions or comments, contact us.Pour toute question ou tout commentaire, nous contacter.Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT •

Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result
in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderate injury.CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation
which, if not avoided, may result in property damage.
CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258) WARNING: To reduce the risk of injury, read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.1) WORK AREA SAFETYa) Keep work area clean and well lit. Cluttered or dark areas invite accidents.b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.2) ELECTRICAL SAFETYa) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.3) PERSONAL SAFETYa) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools may
result in serious personal injury.b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.f) Dress properly. Do not wear loose clothing or jewelery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.4) POWER TOOL USE AND CAREa) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.g) Use the power tool, accessories and tool bits etc., in accordance with these instructions taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could result
in a hazardous situation.5) SERVICEa) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Additional Safety Instructions for Rotary Hammers
• Wear ear protectors. Exposure to noise can cause hearing loss.• Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.
Hold power tools by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. • Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss of
control.• Wear safety goggles or other eye protection. Hammering operations cause chips to fly. Flying particles can cause permanent eye damage. Wear a dust mask or respirator for applications that generate dust. Ear protection may be required for most applications.• Keep a firm grip on the tool at all times. Do not attempt to operate this tool without holding it with both hands. It is recommended that the side handle be used at all times. Operating this tool with one hand will result in loss of control. Breaking through or encountering hard materials such as re-bar may be hazardous as well. Tighten the side handle securely before use.
Do not use this tool to mix or pump easily combustible or explosive fluids (benzine, alcohol,
etc.). Do not mix or stir inflammable liquids labelled accordingly.• Do not operate this tool for long periods of time. Vibration caused by hammer action may be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure by taking frequent rest periods.
Do not recondition bits yourself. Chisel reconditioning should be done by an authorized
specialist. Improperly reconditioned chisels could cause injury.• Wear gloves when operating tool or changing bits. Accessible metal parts on the tool and bits may get extremely hot during operation. Small bits of broken material may damage bare hands.• Never lay the tool down until the bit has come to a complete stop. Moving bits could cause injury.
Do not strike jammed bits with a hammer to dislodge them. Fragments of metal or
material chips could dislodge and cause injury.• Slightly worn chisels can be resharpened by grinding.• Keep the power cord away from the rotating bit. Do not wrap the cord around any part of your body. An electric cord wrapped around a spinning bit may cause personal injury and loss of control.
Air vents often cover moving parts and should be avoided. Loose clothes, jewelery or
long hair can be caught in moving parts.An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that
is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.Minimum Gauge for Cord SetsAmpere RatingVolts Total Length of Cord in Feet (meters)
25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Not More
0 6 18 16 16 14
610 18161412
10 12 16 16 14 12
12 16 14 12 Not Recommended
NOTE: Do not overheat the bit (discoloration) while grinding a new edge. Badly worn chisels
require reforging. Do not reharden and temper the chisel.WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT: ANSI Z87.1 eye protection (CAN/CSA Z94.3), ANSI S12.6 (S3.19) hearing protection, NIOSH/OSHA/MSHA respiratory protection.WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber.Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals. WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.WARNING: Always use eye protection. All users and bystanders must wear eye protection that conforms to ANSI Z87.1.WARNING: Always wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.• The label on your tool may include the following symbols. The symbols and their definitions are as follows:
V ........................ volts A ....................... amperes
Hz ...................... hertz W ...................... watts
min ....................minutes .................... alternating current current ....................alternating or direct current
......................Class I Construction
o ..................... no load speed
.......................... (grounded) ..................... earthing terminal
......................Class II Construction ..................... safety alert symbol
.......................... (double insulated) BPM ................. beats per minute
…/min ...............per minute RPM ................. revolutions per minute
Your DEWALT tool is powered by a DEWALT-built motor. Be sure your power supply agrees
with the nameplate markings. Voltage decrease of more than 10% will cause loss of power and overheating. All DEWALT tools are factory tested.
WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.
A. Variable speed switch F. Chuck
B. Active vibration handle G. Dust cover
(D25223, D25323, D25324 only) H. Depth adjustment rod
C. Forward/reverse slider (D25123, D25213, I. Side handle
D25313, D25223, D25323, D25324) J. Depth stop button
D. Mode selector (D25123, D25213, K. Locking collar (D25324 only)
D25313, D25223, D25323, D25324) L. Lock-on button (D25123, D25330 only)
E. Mode selector button (D25123, D25213, M. Chisel rotation (D25330 only)
D25313, D25223, D25323, D25324)INTENDED USEThese heavy-duty rotary hammers have been designed for professional drilling and hammerdrilling, screwdriving and light chipping at various work sites (i.e., construction sites). DO NOT use under wet conditions or in presence of flammable liquids or gases.These heavy-duty rotary hammers are professional power tools. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.
D25123, D25213, D25313, D25223, D25323, D25324 Heavy-Duty 1" (26 mm) SDS Plus
Rotary Hammers
D25330 Heavy-Duty SDS Plus
Chipping Hammer
Marteaux rotatifs industriels SDS Plus
, 26 mm (1 po), D25123, D25213, D25313, D25223, D25323, D25324
Marteau burineur industriel SDS Plus
Rotomartillos SDS Plus
de 26 mm (1") para trabajos pesados D25123, D25213, D25313, D25223,
D25323, D25324 Martillo de soldador SDS Plus
para trabajos pesados D25330


View the manual for the DeWalt D25123K here, for free. This manual comes under the category Drill Machines and has been rated by 1 people with an average of a 5.3. This manual is available in the following languages: English. Do you have a question about the DeWalt D25123K or do you need help? Ask your question here

Need help?

Do you have a question about the DeWalt D25123K and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other DeWalt D25123K owners to provide you with a good answer.

Number of questions: 0

DeWalt D25123K specifications

Below you will find the product specifications and the manual specifications of the DeWalt D25123K.

Brand DeWalt
Model D25123K
Product Drill Machine
EAN 5035048311639
Language English
Filetype Usermanual (PDF)
Input power 800 W
Power source AC
Impact energy (max) 2.8 J
Rated speed (max) 4300 RPM
Drilling diameter in concrete (max) 26 mm
Drilling diameter in steel (max) 13 mm
Drilling diameter in wood (max) 30 mm
Other features
Weight (including battery) 2900 g
Weight & dimensions
Width 352 mm
Height 200 mm
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the DeWalt D25123K below.

Is your question not listed? Ask your question here

No results