View the manual for the Crivit ER-1512 here, for free. This manual comes under the category hometrainers and has been rated by 2 people with an average of a 7.8. This manual is available in the following languages: English. Do you have a question about the Crivit ER-1512 or do you need help? Ask your question here
| Brand | Crivit |
| Model | ER-1512 |
| Product | hometrainer |
| Language | English |
| Filetype | User manual (PDF) |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Crivit ER-1512 below.
As an adult, it is recommended to do moderately intensive exercise for at least 2.5 hours per week. Preferably spread over several days.
As a rule of thumb for your maximum heart rate, you can use 220 minus your age.
To adjust the resistance level on the Crivit ER-1512 hometrainer, follow these steps: 1. Press the Interval button to start the program. 2. Press the MODE button to select the training intensity using the +/- buttons. You can choose between three intensity levels: L1 for "Trained beginners," L2 for "Advanced or well-trained athletes," and L3 for "Pros and endurance athletes." Confirm the selection with the mode button. 3. To enter additional training targets, refer to the instructions under "GENERAL ENTRIES." 4. Once you have entered all the information, begin cycling to start the training. Please note that the resistance level may vary depending on the program you choose. Some programs may not allow you to change the resistance level while exercising. If you encounter any issues or have further questions, please refer to the troubleshooting section in the manual or contact the service hotline provided.
If the display on your Crivit ER-1512 hometrainer is not working, you can try the following steps to troubleshoot the issue: 1. Check the power supply: Ensure that the hometrainer is properly connected to a power source and that the power cable is securely plugged in. 2. Verify the batteries: If your hometrainer has a battery compartment, check if the batteries are inserted correctly and if they need to be replaced. Refer to the manual for the specific battery type and installation instructions. 3. Reset the display: Sometimes, a simple reset can resolve display issues. Turn off the hometrainer, unplug it from the power source, wait for a few minutes, and then plug it back in and turn it on again. 4. Contact customer support: If the above steps do not resolve the issue, it is recommended to contact the Crivit customer support hotline or refer to the troubleshooting section in the manual for further assistance. They will be able to provide specific guidance based on your situation. Please note that these steps are general troubleshooting suggestions and may not address all possible causes of a non-working display.
To clean and maintain your Crivit ER-1512 hometrainer, follow these steps: 1. Cleaning: Use a clean, damp cloth to wipe down the surfaces of the hometrainer. Avoid using harsh cleaning materials and only clean with water. After cleaning, use a dry cleaning cloth to remove any excess moisture. 2. Care: Keep the hometrainer in a temperature-controlled room to prevent damage. Regularly check for any signs of wear or damage, such as loose screws or broken parts. If you notice any issues, contact customer support for further assistance. 3. Disposal: If you need to dispose of the hometrainer or its packaging, do so in an environmentally friendly manner. Separate different materials for recycling as required. Contact your local waste disposal facilities or authorities for guidance on proper disposal methods. 4. Calibration: The Crivit ER-1512 hometrainer is optimally set and does not require recalibration. However, if you wish to recalibrate the equipment, it is recommended to consult a certified calibration service. Please note that there may be associated costs for this service. By following these steps, you can ensure the cleanliness and proper maintenance of your Crivit ER-1512 hometrainer, promoting its longevity and performance.
To check if the pulse sensors or chest strap on your Crivit ER-1512 hometrainer are working properly, follow these steps: 1. Ensure proper placement: Make sure that the pulse sensors or chest strap are correctly positioned on your body. The pulse sensors are usually located on the handlebars, and the chest strap should be worn around your chest, just below the pectoral muscles. 2. Moisture: Ensure that your skin is clean and free from any lotions or oils that may interfere with the sensors' ability to detect your pulse. Moistening the sensors or chest strap with a small amount of water can improve the contact between the sensors and your skin. 3. Firm contact: Ensure that there is firm contact between the pulse sensors or chest strap and your skin. Adjust the strap or grip the handlebars firmly to ensure a good connection. 4. Check the display: Start pedaling on the hometrainer and check if the display shows your pulse rate. It should be displayed in beats per minute (BPM) or as a numerical value. 5. Test different programs: Try using different training programs on the hometrainer that utilize the pulse sensors or chest strap. Monitor the display to see if it accurately reflects your pulse rate during the workout. If you encounter any issues or the pulse sensors or chest strap are not working properly, refer to the troubleshooting section in the manual or contact the Crivit customer support hotline for further assistance.
If your Crivit ER-1512 hometrainer computer keeps crashing, you can try the following steps to troubleshoot the issue: 1. Check the computer assembly: Ensure that the computer is properly assembled and securely attached to the mount. Refer to the manual for instructions on how to assemble and attach the computer correctly. 2. Verify the cable connections: Check the connections between the computer and the handlebar post. Make sure the cables are securely connected and not pinched or damaged. Ensure that the plugs are inserted correctly and that the polarity is not reversed. 3. Restart the hometrainer: Turn off the hometrainer, unplug it from the power source, and wait for a few minutes. Then, plug it back in and turn it on again. This can help reset the computer and resolve any temporary issues. 4. Contact customer support: If the computer continues to crash despite the above steps, it is recommended to contact the Crivit customer support hotline for further assistance. They will be able to provide specific guidance based on your situation. Please note that these steps are general troubleshooting suggestions and may not address all possible causes of a crashing computer.
Yes, the manual of the Crivit ER-1512 is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Crivit and is the answer not in the manual?
Question and answer
Number of questions: 0