Crivit 1-LD3945 IAN 107990 manual

Crivit 1-LD3945 IAN 107990
8.1 · 5
PDF manual
 · 48 pages
English
manualCrivit 1-LD3945 IAN 107990
IAN

107990

·
1/201
5
· Art.
-
Nr.:
1
-
LD
3945

HEART RATE MONITOR

Usage and safety instructions

MONTRE CARDIO-

FRÉQUENCEMÈTRE

Mode d‘emploi

HORLOGE MET

HARTFREQUENTIEMETER

Gebruiksaanwijzing en veiligheidstips

HERZFREQUENZ-MESSUHR

Bedienungs- und Sicherheitshinweise
Usage and safety instructions ....................................................... - 1 -
Utilisation et avertissements de sécurité .................................... - 23 -
Gebruiksaanwijzing en veiligheidstips ..................................... - 48 -
Bedienungs- und Sicherheitshinweise ............................ - 71 -

View the manual for the Crivit 1-LD3945 IAN 107990 here, for free. This manual comes under the category sport watches and has been rated by 5 people with an average of a 8.1. This manual is available in the following languages: English. Do you have a question about the Crivit 1-LD3945 IAN 107990 or do you need help? Ask your question here

Need help?

Do you have a question about the Crivit and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

General
BrandCrivit
Model1-LD3945 IAN 107990
Productsport watch
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Crivit 1-LD3945 IAN 107990 below.

Do I need to switch off my sport watch at night?

It is sensible for you to switch off your sport watch at night, this ensures longer battery life.

Do I need internet for GPS?

No, no internet is required to receive GPS.

What does the abbreviation GPS stand for?

The abbreviation GPS stands for 'Global Positioning System'.

What is GPS?

GPS is a system that can be used all over the globe to determine your location by means of satellites.

How much should I exercise as an adult per week?

As an adult, it is recommended to do moderately intensive exercise for at least 2.5 hours per week. Preferably spread over several days.

How high is an adult's heart rate at rest?

An adult's resting heart rate is between 60 and 100 beats per minute.

What is an adult's maximum heart rate?

As a rule of thumb for your maximum heart rate, you can use 220 minus your age.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

How do I set the time and date on the Crivit 1-LD3945 IAN 107990 sport watch?

To set the time and date on the Crivit 1-LD3945 IAN 107990 sport watch, follow these steps: 1. Press and hold the SET button for 3 seconds to enter the setting mode. 2. The minutes of the time will start blinking on the display. Use the SEL button to adjust the minutes and press SET to confirm. 3. Set the hours in the same way as step 2. 4. If desired, set the month and day. If neither month nor day are set, the alarm will sound daily. If only the day is set, the alarm will sound monthly. If both the month and day are set, the alarm will sound only on the set date. 5. The setting for the hourly chime will appear on the display. Use SEL to select the desired setting (ON for on, OFF for off) and press SET to confirm. 6. Exit the setting mode by pressing the MODE button. By following these steps, you will be able to set the time and date on your Crivit 1-LD3945 IAN 107990 sport watch.

Why is the display on my Crivit 1-LD3945 IAN 107990 sport watch not working?

If the display on your Crivit 1-LD3945 IAN 107990 sport watch is not working, there could be a few possible reasons. Here are some troubleshooting steps you can try: 1. Check the battery: Ensure that the battery is properly inserted and has enough power. If the battery is low, replace it with a fresh 3V CR2032 battery. 2. Check for electromagnetic interference: Keep the watch at a distance of under 70cm from other heart rate measuring devices or wireless bicycle computers, as they may cause interference. 3. Check the chest belt: Make sure the chest belt is positioned correctly and fits well. Ensure that your skin is not too dry or too cold, as this can affect the contact areas. You can slightly moisten the contact areas to improve function. 4. Reset the watch: If the above steps do not resolve the issue, you can try resetting the watch by simultaneously pressing the SET and SEL buttons. By following these troubleshooting steps, you may be able to resolve the issue with the display on your Crivit 1-LD3945 IAN 107990 sport watch.

How do I change the battery on the Crivit 1-LD3945 IAN 107990 sport watch?

To change the battery on the Crivit 1-LD3945 IAN 107990 sport watch, follow these steps: 1. Use a coin to unscrew the battery cover on the back side of the watch. 2. Insert a new 3V CR2032 battery into the battery compartment, making sure the (+) sign is facing up. 3. Screw the battery cover back into place securely. By following these steps, you will be able to change the battery on your Crivit 1-LD3945 IAN 107990 sport watch.

Why is the heart rate monitor on my Crivit 1-LD3945 IAN 107990 sport watch not accurate?

The heart rate monitor on your Crivit 1-LD3945 IAN 107990 sport watch may not be accurate due to the following reasons: 1. Incorrect positioning of the chest belt: Ensure that the chest belt is positioned correctly and snugly around your chest, just below the breast muscles. Make sure it is not too loose or too tight. 2. Poor contact between the chest belt and your skin: Ensure that the contact areas of the chest belt are moistened slightly to improve the contact with your skin. Dry or cold skin can affect the accuracy of the heart rate measurement. 3. Interference from other devices: Keep the watch at a distance of under 70cm from other heart rate measuring devices or wireless bicycle computers, as they may cause interference. 4. Weak battery: Check the battery level of both the watch and the chest belt. If the batteries are low, replace them with fresh 3V CR2032 batteries. By addressing these potential issues, you can improve the accuracy of the heart rate monitor on your Crivit 1-LD3945 IAN 107990 sport watch.

How do I reset the Crivit 1-LD3945 IAN 107990 sport watch to its factory settings?

To reset the Crivit 1-LD3945 IAN 107990 sport watch to its factory settings, follow these steps: 1. Press and hold the SET and SEL buttons simultaneously for a few seconds to enter the reset mode. 2. While in the reset mode, all the stored data will be erased, including settings and measurements. 3. After resetting, you will need to set up the watch again by following the instructions in the "Setting up the heart rate monitor watch" section of the manual. By following these steps, you can reset your Crivit 1-LD3945 IAN 107990 sport watch to its factory settings. Please note that resetting the watch will delete all the stored data, so make sure to back up any important information before proceeding with the reset.

How do I set the time and date on the Crivit 1-LD3945 IAN 107990 sport watch?

To set the time and date on the Crivit 1-LD3945 IAN 107990 sport watch, follow these steps: 1. Press and hold the SET button for 3 seconds to enter the setting mode. 2. The minutes of the time will start blinking on the display. Use the SEL button to adjust the minutes and press SET to confirm. 3. Set the hours in the same way as step 2. 4. If desired, set the month and day. If neither month nor day are set, the alarm will sound daily. If only the day is set, the alarm will sound monthly. If both the month and day are set, the alarm will sound only on the set date. 5. The setting for the hourly chime will appear on the display. Use SEL to select the desired setting (ON for on, OFF for off) and press SET to confirm. 6. Exit the setting mode by pressing the MODE button. By following these steps, you will be able to set the time and date on your Crivit 1-LD3945 IAN 107990 sport watch.

Why is the display on my Crivit 1-LD3945 IAN 107990 sport watch not working?

If the display on your Crivit 1-LD3945 IAN 107990 sport watch is not working, there could be a few possible reasons. Here are some troubleshooting steps you can try: 1. Check the battery: Ensure that the battery is properly inserted and has enough power. If the battery is low, replace it with a fresh 3V CR2032 battery. 2. Check for electromagnetic interference: Keep the distance between the watch and other heart rate measuring devices within 2 meters. Wireless bicycle computers can also cause interference. 3. Check the chest belt: Make sure the chest belt is positioned correctly and fits well. The contact areas should not be too dry or too cold. You can slightly moisten the contact areas to improve function. 4. Check for display readability: If the display is unreadable or the light does not work, try replacing the batteries. By following these steps, you can troubleshoot and address the issue of the display not working on your Crivit 1-LD3945 IAN 107990 sport watch.

How do I change the battery on the Crivit 1-LD3945 IAN 107990 sport watch?

To change the battery on the Crivit 1-LD3945 IAN 107990 sport watch, follow these steps: 1. Use a coin to unscrew the battery cover on the back side of the watch. 2. Insert a new 3V CR2032 battery into the battery compartment, making sure the (+) sign is facing up. 3. Screw the battery cover back into place securely. By following these steps, you can easily change the battery on your Crivit 1-LD3945 IAN 107990 sport watch.

Why is the heart rate monitor on my Crivit 1-LD3945 IAN 107990 sport watch not accurate?

The heart rate monitor on your Crivit 1-LD3945 IAN 107990 sport watch may not be accurate due to the following reasons: 1. Incorrect positioning of the chest belt: Ensure that the chest belt is positioned correctly and fits snugly around your chest. The contact areas should be moistened slightly for better conductivity. 2. Weak battery: Check the battery level of both the watch and the chest belt. Replace the batteries if they are low to ensure optimal performance. 3. Interference from other devices: Keep the watch at least 2 meters away from other heart rate measuring devices or wireless bicycle computers, as they can cause interference. 4. Incorrect user settings: Make sure that you have entered your age, weight, and height accurately in the watch settings. The maximum heart rate calculation is based on these values. By addressing these factors, you can improve the accuracy of the heart rate monitor on your Crivit 1-LD3945 IAN 107990 sport watch.

How do I reset the Crivit 1-LD3945 IAN 107990 sport watch to its factory settings?

To reset the Crivit 1-LD3945 IAN 107990 sport watch to its factory settings, follow these steps: 1. Press and hold the SET and SEL buttons simultaneously for a few seconds. 2. The watch will enter the reset mode, and all stored data will be erased. 3. To confirm the reset, press the SET button. 4. After the reset, you will need to set up the watch again by following the instructions in the "Setting up the heart rate monitor watch" section. By following these steps, you can reset your Crivit 1-LD3945 IAN 107990 sport watch to its factory settings. Please note that resetting the watch will delete all stored data, so make sure to back up any important information before proceeding with the reset.

Is the manual of the Crivit 1-LD3945 IAN 107990 available in English?

Yes, the manual of the Crivit 1-LD3945 IAN 107990 is available in English .

Is your question not listed? Ask your question here

No results