Crestron DM-RMC-200-S manual

Crestron DM-RMC-200-S
(1)
  • Number of pages: 2
  • Filetype: PDF

DO GUIDE

4. Using the four included 6-32 x 1/4" Phillips head screws,
attach the device to the standoffs.

Inserting the Power Pack

into the Power Pack Holder

To insert the power pack into the power pack holder, do the
following:
1. Slide the power pack into the power pack holder.
2. Using the included 6-32 x 1/2" Phillips pan head screw,
thread the screw through either of the two provided
screw holes to hold the power pack in place.
3. Bundle the excess cable of the power pack into a loop,
and then fasten the bundled cable to the power pack
holder by doing the following:
a. Insert one of the included tie wraps through one of
the tie wrap holes in the power pack holder.
b. Wrap the tie wrap around the bundled cable.

DM-RMC-200-S/DM-RMC-200-S2

DigitalMedia 8G™ Fiber Receiver and Room Controller

DO Install the Device

The Crestron
®
DM-RMC-200-S and DM-RMC-200-S2 mount
onto a 2-gang electrical box using the included support
bracket. The support bracket provides a holder for the included
power pack.

Mounting the Device onto an Electrical Box

To mount the device onto an electrical box, do the following:
1. Attach the four included 6-32 x 1-1/4" standoffs to the
studs of the included support bracket.
2. Using the four included 6-32 x 3/4" combo truss head
screws, attach the included support bracket to the
electrical box.
3. Ground the device and then connect the proper cables to
the bottom of the unit.

DO Check the Box

QTY PRODUCT COLOR PART NUM.
1 Bracket, Support 2047591
2 Connector, 2-Pin 2003574
4 Connector, 2-Pin 2003582
2 Connector, 4-Pin 2003576
1 Connector, 5-Pin 2003577
1 Power Cord, 5' 10" (1.78 m) 2042043
1 Power Pack, 24 Vdc 2.5 A, 100-240 Vac 2045873
1 Screw, 6-32 x 1/2", Pan Head, Phillips Black 2007238
4 Screw, 6-32 x 1/4", Pan Head, Phillips Black 2007215
4 Screw, 6-32 x 3/4", Truss Head, Combo 2009211
4 Standoff, 06-32 x 1-1/4", 1/4" OD, Hex 2007056
2 Tie Wrap, Cable Tie, 15-1/2" x 1" Black 2013608
c. Repeat steps 3a and 3b if necessary using the other
included tie wrap and the remaining tie wrap hole in
the power pack holder.
Installation of the power pack in the holder appears as shown
below.
Tie wrap
hole
Screw
hole*
Tie wrap
hole
Screw
hole*
*Use either screw hole for the included 6-32 x 1/2" Phillips
pan head screw.
Ground
RELAY:
To relay
controllable
devices
AUDIO OUT:
Amplied stereo
audio output
DIG IN:
Software
programmable
digital input
Crestron DM-RMC-200-S

Need help?

Number of questions: 0

Do you have a question about the Crestron DM-RMC-200-S or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Crestron DM-RMC-200-S owners to properly answer your question.

View the manual for the Crestron DM-RMC-200-S here, for free. This manual comes under the category Receivers and has been rated by 1 people with an average of a 7.8. This manual is available in the following languages: English. Do you have a question about the Crestron DM-RMC-200-S or do you need help? Ask your question here

Crestron DM-RMC-200-S specifications

General
Brand Crestron
Model DM-RMC-200-S
Product Receiver
Language English
Filetype PDF

Frequently Asked Questions

Below, you will find the most frequently asked questions about the Crestron DM-RMC-200-S.

Is your question not listed? Ask your question here