Crestron AMP-3210S manual

Crestron AMP-3210S
8.4 · 1
PDF manual
 · 24 pages
English
manualCrestron AMP-3210S

AMP-3210S

3x210W Commercial Power Amplifier, 4/8Ω

crestron.com
|
800.237.2041
> ENERGY STAR
®
qualified power amplifier
> Ultra-efficient space-saving design
> Low total cost of ownership
> High-output power, low noise, low
distortion performance
> Three channels each rated 210W@4Ω
and 120W@8Ω
> Channels 1 and 2 bridgeable for 420W@8Ω
> Individual channel power control via jumper
or remote contact
> Auto power-down after 30 minutes of no signal
> Instant auto power-on when an input signal is detected
> No inrush current during power-up
> Over current and DC offset protection per output
> Thermal protection on the power supply and each channel
> Front panel signal, clip, and fault indicators per channel
> Professional balanced inputs
> Detachable terminal block connectors
> Rear panel ±10dB input level controls
> Convection cooled no noisy fans
> Single-space 1U rack mountable
> Lightweight and under 11 inches deep
> Universal power supply with active power factor correction
Crestron
®
AMP-series Commercial Power Amplifiers provide a perfect
combination of high output and efficiency for all types of professional
audio applications. 100% Crestron engineered and built, these amplifiers
are ENERGY STAR
®
qualified to enable organizations to fulfill their green
initiatives without compromising on audio performance. Advanced design
features include a high-efficiency amp topology with active power factor
corrected power supply, delivering a generous amount of power in a
space-saving 1U rack-mountable chassis.
3-Channel Design
The AMP-3210S provides three independent channels of amplification.
Each channel is rated for 210W @ 4Ω or 120W @ 8Ω, and channels 1 and
2 may be bridged together to deliver a robust 420W @ 8Ω to a single load.
ENERGY STAR
®
Qualified
Its ultra-efficient design allows the AMP-3210S to meet demanding
ENERGY STAR qualification requirements, affording a cost-reducing
solution for boardrooms, auditoriums, and other commercial systems. Auto
power-down places the amplifier into a low-power standby state if no
input signal is detected for 30 minutes. The amplifier quickly powers back
on the instant an input signal is detected. In addition, each amp channel
can be independently enabled or disabled via jumpers or remote contacts,
reducing power consumption by shutting down individual channels when
they are not needed. Whether switched remotely or through an AC power
controller, the AMP-3210S draws no added inrush current during power-
up, reducing AC circuit requirements and potentially eliminating the need
for extra power sequencing equipment.
Professional System Integration
The AMP-3210S includes professional balanced inputs with rear-panel
±10dB input level adjustments to assure compatibility with a wide range
of audio sources. Remote power control is enabled for each channel using
external contact closures, switches, or control system relays. All input,
output, and remote control connections are facilitated via detachable
screw-terminal connectors to simplify installation and servicing.
Cool and Compact
The AMP-3210S features a durable, lightweight chassis that may be
placed on a shelf, or rack-mounted using the rack ears provided. At only
one rack space high and under 11 inches deep, it is ideal for installations
requiring a lot of power in a limited space. Its efficient, cool-running design
gives off substantially less heat than comparably rated amplifiers.
Convection cooling means there are no noisy fans, allowing the
AMP-3210S to be installed in a boardroom lectern or credenza without
affecting noise levels.
Rugged and Dependable
All AMP-series amplifiers are designed for ultimate dependability in a wide
range of commercial environments. Built-in over current and DC offset
protection on each channel helps prevent damage to the amplifier and
speakers due to external or internal faults. Discrete thermal protection is
also provided on each channel and the power supply. Front panel
indicators are provided for each channel to show signal presence,
clipping, and fault conditions.

SPECIFICATIONS

Audio
Typical of 3 mono amplifier channels:
Input Signal Type: Balanced or unbalanced analog line-level
Output Signal Type: 4/8 Ohm
Output Power: 120 Watts at 8 Ohms;
210 Watts at 4 Ohms;
420 Watts at 8 Ohms bridged (channels 1 and 2)

Manual

View the manual for the Crestron AMP-3210S here, for free. This manual comes under the category receivers and has been rated by 1 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the Crestron AMP-3210S or do you need help? Ask your question here

Need help?

Do you have a question about the Crestron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Crestron AMP-3210S specifications

Below you will find the product specifications and the manual specifications of the Crestron AMP-3210S.

General
BrandCrestron
ModelAMP-3210S | AMP-3210S
Productreceiver
LanguageEnglish
FiletypeUser manual (PDF), Datasheet (PDF)
Audio
Audio output channels3.0 channels
Peak power per channel420 W
Amplifier class-
Total Harmonic Distortion (THD)0.05 %
Signal-to-Noise Ratio (SNR)103 dB
Damping factor100
RMS power output per channel (4 Ohm)210 W
RMS power output per channel (8 Ohm)120 W
Crosstalk (1kHz)70 dB
Input sensitivity2.22 mV
Output impedance4/8 Ω
Frequency range20 - 20000 Hz
Ports & interfaces
Speakers connectivity type3.5mm
Technical details
Purpose-
Connectivity technologyWired
Product colorBlack
Cooling typePassive
MaterialMetal, Polycarbonate
Bridge functionYes
Impedance24000 Ω
Sustainability certificatesENERGY STAR
Power
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (typical)126 W
Power consumption (standby)1 W
Weight & dimensions
Width439 mm
Depth263 mm
Height44 mm
Weight3800 g
Operational conditions
Operating temperature (T-T)5 - 40 °C
Operating relative humidity (H-H)10 - 90 %
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Crestron AMP-3210S below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my receiver?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

What is the weight of the Crestron AMP-3210S?

The Crestron AMP-3210S has a weight of 3800 g.

What is the height of the Crestron AMP-3210S?

The Crestron AMP-3210S has a height of 44 mm.

What is the width of the Crestron AMP-3210S?

The Crestron AMP-3210S has a width of 439 mm.

What is the depth of the Crestron AMP-3210S?

The Crestron AMP-3210S has a depth of 263 mm.

Is the manual of the Crestron AMP-3210S available in English?

Yes, the manual of the Crestron AMP-3210S is available in English .

Is your question not listed? Ask your question here

No results