Condair EL manual

Condair EL
8.6 · 1
PDF manual
 · 80 pages
English
manualCondair EL
44 Mounting and installation work

5.4.5 Installing the steam and condensate lines

Installations notes
Use original steam and condensate hose from your Condair representative or solid steam pipes
from copper or stainless steel (min. DIN 1.4301) exclusively. Steam and condensate lines from
other material may cause undesired operational malfunctions.
Initially, lead the steam line upright upwards min. 300 mm above the humidier. Then lead the
steam line with a minimum upslope and/or a minimum downslope of 15 %/8.5° to the steam
distributor.
The condensate hose from the steam distributor is led down to the humidier with a minimum
downslope of 15 %/8.5°, via a condensate trap (min. hose bend diameter Ø200 mm) and there
it is to be connected to the appropriate connector on top of the unit.
Important! Before putting the unit into operation, the condensate trap of the condensate hose must
be lled with water.
The steam line should be kept as short as possible (max. 4 m while observing the minimum bend
radius of 300 mm (for steam hoses) or 5 x internal diameter (with solid steam pipes), respectively.
Important! Allowance must be made for a pressure loss of approx. 100 Pa per meter steam line
and per 90° elbow.
Important! When deciding on the length and layout of steam hoses, it should be noted that steam
hoses may become shorter and/or longer depending on temperature and age.
The steam hose must be secured to the steam distributor and humidi er steam outlet by means of
hose clamps. Solid steam pipes should be connected to the steam distributor and steam humidier
with short lengths of steam hose secured with hose clamps.
Caution! Do not overtighten the hose clamp on the steam connector of the steam humidier.
Steam lines made of solid pipes (copper or stainless steel) must be insulated over the entire length
to minimize condensate formation (=loss).
DANGER!
Reducing the cross section or the complete closure of the steam line will cause an excessive
increase in pressure in the steam cylinder when the unit is operating and could lead to the risk
of scalding accidents. All installations must comply with the following instructions.
When installing make sure the steam line is open over the entire length and through the whole cross
section. Any sealing plugs, adhesive sealing sheets etc. must be removed before connecting the
steam pipe. Reductions in cross section by kinking or crushing must be prevented.
Steam hoses must be prevented from sagging (condensate pockets); if necessary, support steam
hose with pipe clamps, trough, or wall brackets, and install a condensate drain at any low points in
the steam line.
It is not permitted to install a stop valve (e.g. a manually controlled stop valve, solenoid valve,
etc.) in the steam line, due to an inadmissible increase of pressure in the steam cylinder if the valve
is closed during the operation.

Manual

View the manual for the Condair EL here, for free. This manual comes under the category humidifiers and has been rated by 1 people with an average of a 8.6. This manual is available in the following languages: English. Do you have a question about the Condair EL or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Condair and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Condair EL specifications

Below you will find the product specifications and the manual specifications of the Condair EL.

General
BrandCondair
ModelEL
Producthumidifier
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Condair EL below.

Is the manual of the Condair EL available in English?

Yes, the manual of the Condair EL is available in English .

Is your question not listed? Ask your question here

No results