Christopeit VIBRO 3000 manual

Christopeit VIBRO 3000
9.7 · 2
PDF manual
 · 52 pages
English
manualChristopeit VIBRO 3000
1

Heimsport-Trainingsgerät

VIBRO 3000

Montage- und Bedienungsanleitung für
Bestell-Nr. 1970
Notice de montage et d’utilisation du
No. de commande 1970
Assembly and exercise instructions for
Order No. 1970
Montage- en bedieningshandleiding voor
Bestellnummer 1970
GB
D
F NL
Návod k montáži a použití pro
objednací číslo 1970
CZ
Instrukcja instalacji i obsługi dla
Zamówienie nr. 1970
PL
Návod na montáž a použitie pre
objednávacie číslo 1970
SK

View the manual for the Christopeit VIBRO 3000 here, for free. This manual comes under the category vibration plates and has been rated by 2 people with an average of a 9.7. This manual is available in the following languages: English. Do you have a question about the Christopeit VIBRO 3000 or do you need help? Ask your question here

Need help?

Do you have a question about the Christopeit and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

General
BrandChristopeit
ModelVIBRO 3000
Productvibration plate
EAN4044163019703
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Christopeit VIBRO 3000 below.

What should I do if the Christopeit VIBRO 3000 vibration plate is not turning on?

To troubleshoot if the Christopeit VIBRO 3000 vibration plate is not turning on, you can follow these steps: 1. Check the power source: Ensure that the AC connection cable is securely plugged into the AC socket of the VIBRO 3000 and the other end is properly inserted into a suitable and safe installed wall power jack (230V~50Hz). 2. Main switch: Press the ON/OFF main switch to the ON position. Make sure the main switch is turned on. 3. Remote control: If the VIBRO 3000 is equipped with a remote control, check if the batteries are inserted correctly in the battery compartment. Use type "AAA" 1.5V pencells and ensure the correct polarity. 4. Fuse: Check the fuse (5x20mm) located on the VIBRO 3000. If the fuse is blown, replace it with a new one of the same type (T4A/250Volt). 5. Power supply: If the VIBRO 3000 is not receiving power, try plugging it into a different wall power jack to ensure the power source is not the issue. If the VIBRO 3000 still does not turn on after following these steps, it is recommended to contact the manufacturer or a qualified technician for further assistance.

How can I troubleshoot if the intensity levels are not working properly on the VIBRO 3000?

To troubleshoot if the intensity levels are not working properly on the Christopeit VIBRO 3000 vibration plate, you can follow these steps: 1. Check the power supply: Ensure that the VIBRO 3000 is properly connected to a power source and turned on. 2. Verify the selected program: Make sure you have selected the correct exercise program or manually program (P1-P4) on the VIBRO 3000's control panel or remote control. 3. Adjust the speed level: Use the speed increase and decrease buttons on the control panel or remote control to adjust the intensity level. Start with the lowest level and gradually increase it to find the desired intensity. 4. Check the display: Monitor the display on the VIBRO 3000 to ensure that the speed level is changing accordingly when you adjust it using the control panel or remote control. 5. Consult the manual: If the intensity levels are still not working properly, refer to the manual for specific troubleshooting steps or contact the manufacturer's customer support for further assistance. By following these steps, you should be able to troubleshoot and resolve any issues with the intensity levels on the Christopeit VIBRO 3000 vibration plate.

What should I do if the elastic ropes on the VIBRO 3000 are not connecting properly?

If the elastic ropes on the Christopeit VIBRO 3000 vibration plate are not connecting properly, you can follow these steps: 1. Check the ends of the elastic ropes: Inspect the ends of the elastic ropes to ensure they are securely connected and there are no damages. Make sure they are properly attached to the designated hooks or connectors on the VIBRO 3000. 2. Secure the VIBRO 3000: Ensure that the VIBRO 3000 is secured with your body weight to prevent it from lifting up during exercising with the ropes. This will provide stability and prevent any disconnection issues. 3. Check for sufficient space: Make sure there is enough space (approximately 2m²) around the VIBRO 3000 for your individual training session when using the elastic ropes. This will allow you to perform exercises without any restrictions. 4. Avoid excessive bending: Do not bend the elastic ropes more than 1.50m to prevent strain or damage to the ropes. If the elastic ropes still do not connect properly after following these steps, it is recommended to contact the manufacturer's customer service or a qualified technician for further assistance.

How can I troubleshoot if the foot mat on the VIBRO 3000 is not providing the desired intensity?

To troubleshoot if the foot mat on the Christopeit VIBRO 3000 vibration plate is not providing the desired intensity, you can follow these steps: 1. Check your foot position: Ensure that your feet are properly positioned on the foot mat. Place your feet firmly and evenly on the mat, making sure that your weight is evenly distributed. 2. Adjust your stance: Experiment with different foot positions on the foot mat to target different muscle groups and intensify the workout. For example, placing your feet closer together may increase the intensity, while spreading them wider may decrease it. 3. Increase the speed/intensity level: Use the control panel or remote control to increase the speed or intensity level of the VIBRO 3000. Gradually increase the level to find the desired intensity for your workout. 4. Try different exercises: Explore different exercises that can be performed on the VIBRO 3000 to target specific muscle groups and increase the intensity. The manual may provide guidance on various exercises you can try. 5. Consult the manual: If the foot mat still does not provide the desired intensity, refer to the manual for specific troubleshooting steps or contact the manufacturer's customer support for further assistance. By following these steps, you should be able to troubleshoot and adjust the foot mat on the Christopeit VIBRO 3000 vibration plate to achieve the desired intensity for your workout.

What should I do if the VIBRO 3000 is making unusual noises during operation?

If the Christopeit VIBRO 3000 vibration plate is making unusual noises during operation, you can follow these steps to troubleshoot the issue: 1. Check for loose parts: Inspect the VIBRO 3000 for any loose parts or components. Ensure that all screws, bolts, and connections are securely tightened. 2. Verify the surface: Make sure the VIBRO 3000 is placed on a stable and level surface. Uneven surfaces can cause vibrations and noise. Consider using a rubber mat or carpet underneath the vibration plate to reduce noise. 3. Lubricate moving parts: Apply a small amount of silicone lubricant to the moving parts of the VIBRO 3000, such as the pivot points or hinges. This can help reduce friction and noise. 4. Remove any obstructions: Check for any objects or debris that may be obstructing the movement of the VIBRO 3000. Clear away any foreign objects to ensure smooth operation. 5. Contact customer support: If the unusual noises persist, it is recommended to contact the manufacturer's customer support for further assistance. They can provide specific troubleshooting steps or arrange for a technician to inspect and repair the VIBRO 3000 if necessary. By following these steps, you should be able to troubleshoot and address any unusual noises coming from the Christopeit VIBRO 3000 vibration plate during operation.

Is the manual of the Christopeit VIBRO 3000 available in English?

Yes, the manual of the Christopeit VIBRO 3000 is available in English .

Is your question not listed? Ask your question here

No results