Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies8401 Eagle Creek Parkway, Savage, MN 55378• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
SSB-014, SSM-014, SLB-014 and SLM-014 Interface Brackets
SSB-014, SSM-014, SLB-014 and SLM-014 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING:IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING:OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing Interface bracket.
NOTE:Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.2. Turn projector upside down.3. Place the 3/16” nylon spacers over the threaded insert in the bottom of the projector.
4.Place the interface bracket onto the bottom of the projector so the screws are pointed away from projector with the two tabs behind the
rear feet on the projector.
5.At this time the mounting hole in the bracket should be aligned with the nylon spacer and the threaded mounting hole in the projector.
6. Using the ¼” x ½” flat screw, secure interface bracket to projector and tighten all fasteners at this time.
NOTE:Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.(1) Interface Bracket (1) 1/4” X 1/2” Flat Head Screw(4) 10 - 24 Thumb Nuts** (1) 1/2" x .260 x 3/16" Nylon Spacer(1) All-Points Security Kit**Only used when installing SLB/SSB interface brackets.
NOTE:Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
interface bracket installation.
(
N
o
t
e
:
S
S
M
-
s
t
y
l
e
i
n
t
e
r
f
a
c
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(N
ote: SS
B-sty
le inte
rf
a
c
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
SLM-014
SLB-014
Towards front of
projector
Towards front of
projector
View the manual for the Chief SSB014 here, for free. This manual comes under the category Projector accessories and has been rated by 1 people with an average of a 7.3. This manual is available in the following languages: English. Do you have a question about the Chief SSB014 or do you need help? Ask your question here
Need help?
Do you have a question about the Chief and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Chief owners to provide you with a good answer.
Need help?
Do you have a question about the Chief and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Chief owners to provide you with a good answer.
Number of questions: 0