Casio Waveceptor WV200A-1AV manual

Casio Waveceptor WV200A-1AV
7.8 · 8
PDF manual
 · 5 pages
English
manualCasio Waveceptor WV200A-1AV

Operation Guide 3140

2

Important!

When getting ready to receive the time calibration signal, position the watch as
shown in the nearby illustration, with its 12 oclock side facing towards a window.
This watch is designed to receive a time calibration signal late at night. Because of
this, you should place the watch near a window as shown in the illustration when
you take it off at night. Make sure there are no metal objects nearby.
12 o’clock
or
Make sure the watch is facing the right way.
Proper signal reception can be dif cult or even impossible under the conditions listed
below.
Inside a
vehicle
Near
household
appliances,
office
equipment,
or a mobile
phone
Near a
construction
site, airport,
or other
sources of
electrical
noise
Near
high-tension
power lines
Among or
behind
mountains
Inside or
among
buildings
Signal reception normally is better at night than during the day.
Time calibration signal reception takes from two to seven minutes. Take care that
you do not perform any button operations or move the watch during this time.
The time calibration signal the watch will attempt to pick up depends on its current
Home City code setting as shown below.
Home City Codes and Transmitters
Home City Code Transmitter Frequency
HNL*, ANC*, YVR, LAX, YEA,
DEN, MEX, YWG, CHI, MIA,
YTO, NYC, YHZ, YYT
Fort Collins, Colorado
(the United States)
60.0 kHz
LIS, LON, MAD, PAR, ROM,
BER, STO, ATH*, MOW*
Anthorn (England) 60.0 kHz
* The areas covered by the HNL , ANC , ATH , and MOW city codes are quite far
from the time calibration signal transmitters, and so certain conditions may cause
problems with signal reception.
Approximate Reception Ranges
U.S. Signal
Fort Collins
600 miles
(1,000 kilometers)
2,000 miles
(3,000 kilometers)
Anthorn
500 kilometers
1,500 kilometers
U.K. signal transmitter approximate
reception ran
g
e as of April 2007
U.K. Signal
Signal reception may not be possible at the distances noted below during certain
times of the year or day. Radio interference may also cause problems with reception
.
Anthorn (England) transmitter: 500 kilometers (310 miles)
Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)
In April 2007, the U.K. signal transmitter was moved from Rugby to Anthorn, which
resulted in a slight shift in the approximate reception range of the signal. The shift is
so slight that there is virtually no change in the ability to receive the signal
.
Even when the watch is within the reception range of a transmitter, signal reception
may be impossible at times due to the effects of geographic contours, structures,
weather, the season of the year, the time of day, radio interference, etc. Note that
the signal becomes weaker at distances of approximately 500 kilometers from the
transmitter, which means that the in uence of the conditions listed above becomes
even greater
.

About Auto Receive

The watch receives the time calibration signal automatically up to six times a day.
When any auto receive is successful, the remaining auto receive operations are not
performed. The reception schedule (calibration times) depends on your currently
selected Home City, and whether standard time or Daylight Saving Time is selected
for your Home City.
Your Home City
Auto Receive Start Times
123456
HNL, ANC, YVR,
LAX, YEA, DEN,
MEX, YWG, CHI,
MIA, YTO, NYC,
YHZ, YYT
Standard Time
Daylight
Saving Time
Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am
LIS, LON
Standard Time 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am
Midnight
*
Daylight
Saving Time
2:00 am 3:00 am 4:00 am 5:00 am
Midnight
*
1:00 am
*
MAD, PAR, ROM,
BER, STO
Standard Time 2:00 am 3:00 am 4:00 am 5:00 am
Midnight
*
1:00 am
*
Daylight
Saving Time
3:00 am 4:00 am 5:00 am
Midnight
*
1:00 am
*
2:00 am
*
ATH
Standard Time 3:00 am 4:00 am 5:00 am
Midnight
*
1:00 am
*
2:00 am
*
Daylight
Saving Time
4:00 am 5:00 am
Midnight
*
1:00 am
*
2:00 am
*
3:00 am
*
MOW
Standard Time 4:00 am 5:00 am
Midnight
*
1:00 am
*
2:00 am
*
3:00 am
*
Daylight
Saving Time
5:00 am
Midnight
*
1:00 am
*
2:00 am
*
3:00 am
*
4:00 am
*
* Next day
Note
When a calibration time is reached, the watch will receive the calibration signal
only if it is in either the Timekeeping Mode or World Time Mode. Reception is not
performed if a calibration time is reached while you are con guring settings.
Auto receive of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can receive the signal easily.
The watch receives the calibration signal for two to seven minutes everyday when
the time in the Timekeeping Mode reaches each of the calibration times. Avoid
performing any button operation within seven minutes before or after any one of the
calibration times. Doing so can interfere with correct calibration.
Remember that reception of the calibration signal depends on the current time in the
Timekeeping Mode. The receive operation will be performed whenever the display
shows any one of the calibration times, regardless of whether or not the displayed
time actually is the correct time.
Calibration signal reception is disabled while a countdown timer operation is in
progress.

About the Receiving Indicator

The receiving indicator shows the strength of the calibration signal being received.
For best reception, be sure to keep the watch in a location where signal strength is
strongest.
Weak
(Level 0)
Strong
(Level 3)
Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the receiving indicator to indicate signal strength.
Use the receiving indicator as a guide for checking signal strength and for nding the
best location for the watch during signal receive operations.
Following reception of the time calibration signal and calibration of the watchs time
setting, the Level 3 receiving indicator will remain on the display in all modes. The
Level 3 receiving indicator will not be displayed if signal reception was unsuccessful
or after you adjust the current time setting manually
.
The Level 3 receiving indicator is displayed only when the watch is able to receive
both time and date data successfully. It does not appear when only time data is
received.
The Level 3 receiving indicator indicates that at least one of the auto calibration
signal receive operations was successful. Note, however, that the Level 3 receiving
indicator is cleared from the display when the rst auto receive operation of the day
is performed.
To perform manual receive
1. Place the watch on a stable surface so its top (12
oclock side) is facing towards a window.
2. In the Timekeeping Mode, hold down
D
for about two
seconds until RC! appears on the display.
Time calibration signal reception takes from two to
seven minutes. Take care that you do not perform any
button operations or move the watch during this time.
After signal reception is complete, the display of the
watch changes to the Last Signal screen.
Note
To interrupt a receive operation and return to the Timekeeping Mode, press
D
.
If the receive operation is unsuccessful, the message
ERR
appears on the display for
about one or two minutes. After that, the watch returns to the Timekeeping Mode.
You can also change from the Last Signal or
ERR
screen to the normal timekeeping
screen by pressing
D
.
Calibration signal reception is disabled while a countdown timer operation is in
progress.
To turn auto receive on and off
1. In the Timekeeping Mode, press
D
to display the Last
Signal screen.
2. Hold down
A
until the receiving indicator and current
auto receive setting (
or ) start to ash.
This is the setting screen.
Note that the setting screen will not appear if the
currently selected Home City is one that does not
support time calibration reception.
3. Press
D
to toggle auto receive on (
) and off
(
).
4. Press
A
to exit the setting screen.
For information about city codes that support signal receive, see To specify your
Home City.
To display the Last Signal screen
In the Timekeeping Mode, press
D
to display the Last Signal screen (indicated by
GET
). The Last Signal screen shows the date and time of the last successful time
calibration signal reception.
Dayofweek
Home Time
(Hour : Minutes Seconds)
Month Day
Receive time
Receive date
Year
PM indicator
Current Time and Date Screen Last Signal Screen
Press .
DST indicator
Receivin
g
indicator
Receivin
g
indicator
On/Off Status

View the manual for the Casio Waveceptor WV200A-1AV here, for free. This manual comes under the category sport watches and has been rated by 8 people with an average of a 7.8. This manual is available in the following languages: English. Do you have a question about the Casio Waveceptor WV200A-1AV or do you need help? Ask your question here

Need help?

Do you have a question about the Casio and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 24
R
Rick BurdettAugust 19, 2021

My watch has been in a drawer for a year and appears dead. How can I restore it?

2 comments
E
Emma of manua.lsOctober 25, 2023

To restore your Casio Waveceptor WV200A-1AV watch after it has been in a drawer for a year and appears dead, follow these steps: 1. Press and hold the A button in the Timekeeping Mode until the city code starts to flash, indicating the setting screen. 2. Press the C button to navigate to the DST (Daylight Saving Time) setting screen. 3. Use the D button to cycle through the DST settings. Select "DST off" to disable Daylight Saving Time. 4. Press the A button to exit the setting screen.

This answer is automatically generated
F
Frank October 7, 2023

This just happened to me, but mine had been unused for several years. I simply replaced the battery (app $3 at Amazon). Now, I'm going through the process of setting the time and date.

J
John Beals September 13, 2021

How do I set the count down timer to the amount of time I want to count down from?

B
Bernard DurackOctober 13, 2022

My analog time has become 5 minutes slower than the real digital time. Can it be corrected please ?

My analog time has become 5 minutes slower than the real digital time. Can it be corrected please ?
zoom-in
View photo
I
IanApril 4, 2024

how can I adjust the hand setting, the analog time is 1 minute behind the digital. Thankyou Ian

J
Jeff CosterJuly 7, 2022

What kind of battery does a Casio 3140 wv_200a

What kind of battery does a Casio 3140 wv_200a
zoom-in
View photo
J
jJoseph CHAGOURYSeptember 4, 2022

how do i change the time format from 24 hours to 12 hours format

D
Dr Leo LeungSeptember 30, 2022

if this watch will not charge what can I do...battery replacement?

H
Harold H. Yearwood, IINovember 28, 2022

What battery do I need for my Wave Ceptor Illuminator WV-200A watch?

1 comment
F
FrankOctober 7, 2023

CR-1620

L
LoApril 25, 2019

How do I fix year on Casio waveceptor 200a

The Casio Waveceptor WV200A-1AV is a sport watch that offers a range of practical features for active individuals. With its waterproof design and water resistant depth of 200 meters, this watch can withstand water pressure and is suitable for swimming, snorkeling, and other water activities. The watch includes a calendar function, allowing users to keep track of dates and appointments. It also offers a clock mode in both 12-hour and 24-hour formats, providing flexibility for personal preference. A stopwatch function is available, which is useful for timing activities and workouts. This allows users to measure their performance or monitor their progress during exercise sessions. With its world time function, the Casio Waveceptor WV200A-1AV enables users to keep track of different time zones. This can be helpful for travelers or individuals who need to coordinate with people in different parts of the world. The watch has dimensions of 48.3 x 39 x 12.5 millimeters, making it compact and comfortable to wear. Weighing only 40 grams, it is lightweight and won't be burdensome during physical activities. The band material is made of resin, which offers durability and resistance to wear and tear. The watch features an LCD dial, providing clear and easy-to-read information. The Casio Waveceptor WV200A-1AV operates on a CR1620 battery, ensuring long-lasting power for extended use. In summary, the Casio Waveceptor WV200A-1AV is a practical and reliable sport watch with a range of features, including waterproof capability, a calendar, clock modes, stopwatch function, world time function, and a durable resin band. Its compact size and lightweight design make it a convenient accessory for active individuals.

General
BrandCasio
ModelWaveceptor WV200A-1AV | WV200A-1AV
Productsport watch
EAN630219282814, 79767898281, 0630219282814, 0797678982812, 0079767898281
LanguageEnglish
FiletypeUser manual (PDF)
Technical details
WaterproofYes
200 m
CalendarYes
Clock mode12h/24h
StopwatchYes
Accuracy+/- 20 sec/month
World time functionYes
Watch dial typeLCD dial
Other features
Dimensions (WxDxH)48.3 x 39 x 12.5 mm
Product colorBlack
Weight & dimensions
Weight40 g
Design
Band materialResin
Power
Battery typeCR1620
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Casio Waveceptor WV200A-1AV below.

What is the weight of the Casio Waveceptor WV200A-1AV?

The Casio Waveceptor WV200A-1AV has a weight of 40 g.

Do I need to switch off my sport watch at night?

It is sensible for you to switch off your sport watch at night, this ensures longer battery life.

Do I need internet for GPS?

No, no internet is required to receive GPS.

What does the abbreviation GPS stand for?

The abbreviation GPS stands for 'Global Positioning System'.

What is GPS?

GPS is a system that can be used all over the globe to determine your location by means of satellites.

How much should I exercise as an adult per week?

As an adult, it is recommended to do moderately intensive exercise for at least 2.5 hours per week. Preferably spread over several days.

How high is an adult's heart rate at rest?

An adult's resting heart rate is between 60 and 100 beats per minute.

What is an adult's maximum heart rate?

As a rule of thumb for your maximum heart rate, you can use 220 minus your age.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

How do I set the time and date on my Casio Waveceptor WV200A-1AV?

To set the time and date on your watch, press and hold the "Adjust" button until the time starts flashing. Use the "Forward" and "Back" buttons to adjust the time, and press "Adjust" again to move to the date setting. Repeat the same process to set the date.

My watch is not receiving the radio signal to automatically update the time. What should I do?

First, ensure that you are in an open area with good reception. Then, press and hold the "Adjust" button to enter the time-setting mode. Look for the "RX-Signal" display and press the "Forward" button to initiate the radio signal reception manually. Keep the watch still until the signal is received.

The display on my watch is too dim. Can I adjust the brightness?

Yes, you can adjust the brightness of your watch's display. Press and hold the "Forward" button to enter the brightness adjustment mode. Use the "Forward" and "Back" buttons to toggle between brightness levels. Once you've selected the desired brightness level, simply wait for a few seconds for the change to be saved.

How do I use the stopwatch function on my Casio Waveceptor WV200A-1AV?

To use the stopwatch function, press the "Mode" button until the watch enters the "STW" mode. Press the "Start/Stop" button to begin timing, and press it again to stop. To reset the stopwatch, press and hold the "Adjust" button.

How can I change the unit of measurement for the temperature display on my watch?

Changing the unit of measurement for the temperature display is quite easy. Press and hold the "Mode" button to enter the settings mode. Use the "Forward" button to navigate to the temperature settings, and then use the "Adjust" button to toggle between Celsius and Fahrenheit. Once you've selected your preferred unit, press "Mode" to exit the settings mode.

Is the Casio Waveceptor WV200A-1AV waterproof?

Yes, the Casio Waveceptor WV200A-1AV is waterproof. This means that it can be worn while swimming or diving.

Does the Casio Waveceptor WV200A-1AV have a calendar?

Yes, the Casio Waveceptor WV200A-1AV has a calendar. This allows the user to easily keep track of the date.

Can the clock mode of the Casio Waveceptor WV200A-1AV be set to 12h or 24h?

Yes, the clock mode of the Casio Waveceptor WV200A-1AV can be set to either 12h or 24h. This allows the user to choose their preferred time format.

Does the Casio Waveceptor WV200A-1AV have a stopwatch?

Yes, the Casio Waveceptor WV200A-1AV has a stopwatch. This allows the user to accurately measure time intervals.

Does the Casio Waveceptor WV200A-1AV have a world time function?

Yes, the Casio Waveceptor WV200A-1AV has a world time function. This allows the user to easily view the time in different time zones.

Is the manual of the Casio Waveceptor WV200A-1AV available in English?

Yes, the manual of the Casio Waveceptor WV200A-1AV is available in English .

Is your question not listed? Ask your question here

No results