Casio G-SHOCK Classic GA-110MB-1AER manual

Casio G-SHOCK Classic GA-110MB-1AER
8.5 · 2
PDF manual
 · 6 pages
English
manualCasio G-SHOCK Classic GA-110MB-1AER

Operation Guide 5146 5425

E-10
3. Press
&
to change the fl ashing screen content in the sequence shown below to
select the other settings.
Seconds
12/24-Hour
Format
Hour
Minutes
DST
Month
Year
City Code
Day
Illumination
Duration
4. When the setting you want to change is fl ashing, use
'
or
%
to change it as
described below.
Screen: To do this: Do this:
Change the city code Use
'
(east) and
%
(west).
Toggle the DST setting between
Daylight Saving Time (
on
) and
Standard Time (
OFF
).
Press
'
.
Toggle between 12-hour (
12H
) and
24-hour (
24H
) timekeeping
Press
'
.
E-11
Screen: To do this: Do this:
Reset the seconds to
00
Press
'
.
Change the hour and minutes
Use
'
(+) and
%
(–).
Change the year, month, or day
Toggle the display illumination
duration between 1.5 seconds (
LT1
)
and three seconds (
LT3
)
Press
'
.
5. Press
$
to exit the setting mode.
The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
E-12
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down
$
for about three
seconds until the currently selected city code fl ashes in
the upper digital display. This is the setting mode.
2. Press
&
. This will display the DST setting screen.
3. Use
'
to toggle the DST setting on (
on
) and off (
OFF
).
The default DST setting is off (OFF).
4. When the setting you want is selected, press
$
to exit
the setting mode.
The DST indicator appears to indicate that Daylight
Saving Time is turned on.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
DST indicator
E-13
12-hour and 24-hour timekeeping
With the 12-hour format, the PM indicator (
P
) appears for times in the range of noon
to 11:59 p.m. and no indicator appears for times in the range of midnight to 11:59
a.m.
With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (
P
).
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
E-14
Stopwatch
You can use the stopwatch to measure elapsed time, lap
times and split times. If you specify a distance value, the
stopwatch also will calculate and display speeds.
The digital display range of the stopwatch is 99 hours,
59 minutes, 59.999 seconds. The stopwatch continues
to run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
The stopwatch operation continues even if you exit the
Stopwatch Mode. If you exit the Stopwatch Mode while
a stopwatch operation is in progress, the segments
along the top of the upper digital display (upper display
segments) will indicate the seconds of the current time.
Each segment represents one second. This is to let you
know that a stopwatch operation is in progress.
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing
&
(page
E-7).
Speed hand
Upper display
segments
E-15
Important!
Check to make sure that the speed hand is not moving before you perform any
Stopwatch Mode button operation.
Specifying a Distance Value
You can use the procedure below to specify a distance value, if you want. If you
specify a distance value, the watch will calculate and indicate speed for certain
stopwatch operations.
The distance value represents kilometers, miles, or any other distance unit you
want. Specifying a distance value of 10.0, for example, can mean 10.0 kilometers
or 10.0 miles.
No speed calculation is performed when 0.0 is specifi ed as the current distance
value.
For lap time readings, you can specify either the lap distance (when all the laps are
the same distance) or the total race distance.
For split time readings, you can specify the total race distance only. Though the
watch will indicate a speed each time you take a split reading, they will be based
on the total race distance, and so they will not indicate actual intermediate split
speeds.
E-16
To specify a distance value
1. In the Stopwatch Mode, make sure the stopwatch is
stopped and reset to all zeros.
If you need to reset the stopwatch to all zeros, press $.
2.
Hold down
$
for about three seconds until the current
distance value setting fl ashes in the lower digital display.
This is the distance value setting mode.
3. Press
&
to move the fl ashing between the values on
the left side and right side of the distance value decimal
point.
4. While a distance value is fl ashing, use
'
(+) and
%
(–)
to change it.
You can specify a distance value in the range of 0.1
to 99.9.
5. After specifying the distance value you want, press
$
to exit the setting mode.
l
l
l
l
l
l
l
l
l
l
l
E-17
How speed is indicated
While an elapsed time measurement operation is being
performed in the Stopwatch Mode, the watch will
indicate a speed value, which is calculated based on
the distance you specifi ed and the elapsed time.
The speed value is indicated as described below.
Speed hand: Up to 100
Upper display segments: 100 unit
A
1000
indicator points to 1000 (located to the right of
the upper display segments) when the speed value
exceeds 1000.
The speed hand indicates speed values less than 100.
Only even-numbered values are indicated.
Speed can be indicated from 0 to 1998.
OVER
is indicated
by the speed hand when the speed exceeds 1998.
Example:
When the speed value is 1,740.
Speed hand: Indicates
40
.
Upper display segments: Indicate
700
.
1000
indicator: Displayed
Speed hand
(Up to 100)
Segments
(100 unit)
OVER
1000 indicator
E-18
Time Measurement
You need to specify either lap time (page E-20) or split time (page E-22) measurement
before you start a stopwatch operation.
If you want to measure total elapsed time, select split time measurement.
To specify lap time or split time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
Make sure that LAP (lap times) or SPL (split times) is shown in the lower digital
display.
If you need to reset the stopwatch to all zeros, press $.
2. You can toggle between LAP (lap times) and SPL (split times) by pressing
$
.
$
E-19
Elapsed Time Measurement
Use the following procedure to measure elapsed time, without taking lap time or split
time readings.
To perform elapsed time measurement
Select split time (SPL) measurement and then perform the following button operations.
'
Start
'
Stop
$
Reset
If you have a distance value (page E-15) specifi ed for the current elapsed time
measurement, the upper display segments and speed hand will indicate the speed
when you press
'
to stop the elapsed time operation.
After pressing
'
to stop an elapsed time operation, you could press
'
again to
restart from the point where you left off.

Manual

View the manual for the Casio G-SHOCK Classic GA-110MB-1AER here, for free. This manual comes under the category watches and has been rated by 2 people with an average of a 8.5. This manual is available in the following languages: English. Do you have a question about the Casio G-SHOCK Classic GA-110MB-1AER or do you need help? Ask your question here

Need help?

Do you have a question about the Casio and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Casio G-SHOCK Classic GA-110MB-1AER specifications

Below you will find the product specifications and the manual specifications of the Casio G-SHOCK Classic GA-110MB-1AER.

The Casio G-SHOCK Classic GA-110MB-1AER is a watch that combines functionality and style. With its black resin case and strap, it has a sleek and modern look. The GA-110MB-1AER features a digital display with large, easy-to-read numbers and a range of useful features. The watch is shock-resistant, meaning it can withstand the impact of everyday activities without being damaged. It also has a water resistance rating of 200 meters, making it suitable for swimming and diving. The GA-110MB-1AER has a built-in stopwatch, countdown timer, and multiple alarm settings, allowing users to keep track of time and manage their schedules effectively. It also has an automatic calendar, which eliminates the need for manual adjustment. The watch is powered by a reliable quartz movement, ensuring accurate timekeeping. The battery life is approximately two years, so users don't have to worry about frequent replacements. One standout feature of the GA-110MB-1AER is its LED backlight, which provides visibility in low-light situations. This makes it easy to read the time, even in the dark. Overall, the Casio G-SHOCK Classic GA-110MB-1AER is a durable and versatile watch that offers practicality and style. Its features and design make it suitable for everyday wear and various activities.

General
BrandCasio
ModelG-SHOCK Classic GA-110MB-1AER
Productwatch
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Casio G-SHOCK Classic GA-110MB-1AER below.

A battery in my watch has started to corrode. Is the device still safe to use?

The product can still be used safely after proper cleaning. Remove the battery with gloves and clean the battery compartment with a toothbrush and vinegar. After drying, new batteries can be inserted into the device.

Why is the time displayed on my Casio G-SHOCK Classic GA-110MB-1AER watch incorrect?

Ensure that you have properly set your home city's time zone and adjusted for Daylight Saving Time if necessary. Also, check if the watch is receiving a proper signal from the atomic timekeeping feature, as interference can affect its accuracy.

How can I enable the stopwatch feature on my Casio G-SHOCK Classic GA-110MB-1AER watch?

Press the top-right button to access the stopwatch mode. Press the bottom-right button to start or pause the stopwatch, and the top-right button to reset it. Keep in mind that the stopwatch can measure up to 1/100th of a second for the first 60 minutes, and after that, it switches to 1-second intervals.

How do I set multiple alarms on my Casio G-SHOCK Classic GA-110MB-1AER watch?

To set an alarm, press the lower-left button twice to access the alarm mode. Press the upper-right button to select the alarm you wish to set, then use the upper-left and lower-right buttons to adjust the desired time. Once set, press the upper-right button to activate the alarm.

How can I switch the time format from 12-hour to 24-hour on my Casio G-SHOCK Classic GA-110MB-1AER watch?

Press and hold the lower-left button for a few seconds to access the time format setting. Use the upper-right and lower-right buttons to toggle between the 12-hour and 24-hour formats. Confirm your selection by pressing the lower-left button.

Why is the backlight not turning on in my Casio G-SHOCK Classic GA-110MB-1AER watch?

Ensure that the "Auto Light" function is enabled by pressing and holding the upper-left button for about two seconds. Additionally, make sure that the watch is in a sufficiently dark environment for the electro-luminescent panel to activate. If the problem persists, check if the battery needs replacement.

Is the manual of the Casio G-SHOCK Classic GA-110MB-1AER available in English?

Yes, the manual of the Casio G-SHOCK Classic GA-110MB-1AER is available in English .

Is your question not listed? Ask your question here

No results