Casio 3461 manual

Casio 3461
5.9 · 1
PDF manual
 · 22 pages
English
manualCasio 3461

Using the Timer

1.
Use the operations below to perform a
timer operation.
D
D
D
(Time up)
Resume
Pause
(Measurement operation starts.)
Start
A beeper will sound for 10 seconds to
let you know when the end of a
countdown is reached.
To reset a paused countdown to the
start time, press (A).
2.
Press any button to stop the tone.

Light

The watch has an LED light that you can use
to
illuminate the display for about two seconds
for viewing in the dark. When turned on,
illumination becomes gradually brighter and
then gradually dimmer.
The watch also has an auto light function that
automatically illuminates the display
whenever the watch is angled for reading in
the dark.

Illuminating the Display

Manually

Pressing (B) turns on illumination.
The LED light will turn off automatically if the
alarm starts to sound.

Auto Light

If Auto Light is enabled, display illumination
will
turn on automatically whenever the watch
is positioned at an angle of 40 degrees or more
when it is dark.
40
degrees
or more
Important!
Auto Light may not operate properly
when
the watch is at a horizontal angle
of 15 degrees or greater from
horizontal as shown in the illustration
below.
Auto
Light may operate unintentionally
and run down the battery if the watch
is blocked from light by your sleeve.
Electro-static charge or magnetism
can interfere with proper auto light
operation. If this happens, try lowering
your arm and then angle it towards
your face again.
When moving the watch you may note
a slight rattling sound. This is due to
operation of the auto light switch,
which determines the current
orientation of the watch. It does not
indicate malfunction.
Note
Auto
Light is disabled when any one of
the conditions below exists.
Alarm, timer alert, or other beeper
sounding

Configuring the Auto Light

Setting

1.
Enter the Timekeeping Mode.
l
Navigating Between Modes
2.
Hold down (B) for about three seconds.
Each time (B) is held down for about
three seconds, Auto Light will toggle
between enabled and disabled.
DisabledEnabled

Specifying the Illumination

Duration

You can select either two seconds or four
seconds as the illumination duration.
1.
Enter the Timekeeping Mode.
l
Navigating Between Modes
2.
Hold
down (A) for about two seconds until
[HT] flashes.
3.
Press (C) 12 times to display
[LIGHT].
4.
Press (D) to toggle between the two
illumination duration settings.
[2]: 2-second illumination
[4]: 4-second illumination
5.
Press (A) to exit the setting screen.

Operation Guide 3459/3461

15

View the manual for the Casio 3461 here, for free. This manual comes under the category smartwatch and has been rated by 1 people with an average of a 5.9. This manual is available in the following languages: English. Do you have a question about the Casio 3461 or do you need help? Ask your question here

Need help?

Do you have a question about the Casio and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Casio 3461 is a smartwatch that offers a variety of features and functionality. Designed for everyday use, it is equipped with a range of tools to assist users in managing their daily activities. The watch boasts a durable construction, ensuring long-lasting reliability. It is resistant to water and dust, making it suitable for use in various environments. The Casio 3461 is also equipped with advanced technology that allows it to connect seamlessly with other devices, such as smartphones, providing users with access to important notifications and information. Featuring a built-in GPS system, the Casio 3461 enables users to track their location and navigate accurately. Additionally, it offers an array of health and fitness features, including a heart rate monitor and step counter, allowing users to monitor their physical activity and overall well-being. The watch also offers a variety of different modes, such as a stopwatch and timer, catering to different user needs. The Casio 3461 features a customizable display, allowing users to personalize the appearance of the watch face. Furthermore, it offers a long battery life, ensuring that users can rely on it for extended periods without needing to recharge. Overall, the Casio 3461 is a practical and reliable smartwatch that combines durability with advanced functionality. Whether for everyday use or specific activities, it provides users with the tools they need to manage their time and stay connected.

General
BrandCasio
Model3461
Productsmartwatch
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Casio 3461 below.

Does a smartwatch have functionalities that a smartphone does not have?

In general, a smartwatch has no functionalities that a smartphone does not have.

Do I need to switch off my smartwatch at night?

It is sensible for you to switch off your smartwatch at night, this ensures longer battery life.

Do I need internet for GPS?

No, no internet is required to receive GPS.

What does the abbreviation GPS stand for?

The abbreviation GPS stands for 'Global Positioning System'.

What is GPS?

GPS is a system that can be used all over the globe to determine your location by means of satellites.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

How do I check if my phone is compatible with the Casio 3461 smartwatch?

To check if your phone is compatible with the Casio 3461 smartwatch, follow these steps: 1. Visit the CASIO website for information about phones that can connect with the watch. You can find the website link in the manual. 2. On the CASIO website, look for the section on supported phones. This section will provide you with a list of phones that are compatible with the Casio 3461 smartwatch. 3. Check if your phone model is listed in the supported phones section. If your phone model is listed, it means that it is compatible with the smartwatch. 4. If your phone model is not listed, it may not be compatible with the Casio 3461 smartwatch. In this case, you may need to consider using a different phone that is listed as compatible. Please note that the compatibility of the smartwatch with different phone models may vary, so it is important to refer to the supported phones section on the CASIO website for the most accurate and up-to-date information.

Why is the time on my Casio 3461 smartwatch not accurate?

The time on your Casio 3461 smartwatch may not be accurate due to the following reasons: 1. Signal Reception: Ensure that the watch is receiving a strong time signal. Check if you are in an appropriate signal reception location and within the time signal reception range. 2. Auto Time Adjustment: Make sure the auto time adjustment feature is enabled. This allows the watch to automatically adjust the time based on the received time signal. 3. Manual Time Adjustment: If the auto time adjustment is not possible or the signal reception is weak, manually adjust the time on your watch using the watch operations. Refer to the manual for detailed instructions on how to adjust the time manually. 4. Power Saving Function: If the watch is in power-saving mode, the timekeeping function may be temporarily disabled to conserve battery power. Ensure that the watch is not in power-saving mode. 5. Battery Power: Low battery power can affect the accuracy of the time. Check the battery level of your watch and recharge it if necessary. If the issue persists, refer to the troubleshooting section in the manual for further assistance.

How do I connect my Casio 3461 smartwatch to my phone using the mobile link feature?

To connect your Casio 3461 smartwatch to your phone using the mobile link feature, follow these steps: 1. Make sure your phone is compatible with the Casio 3461 smartwatch. Check the supported phone models on the CASIO website. 2. Install the G-SHOCK Connected app on your phone. This app is required to connect with the watch. 3. Enable Bluetooth on your phone. Refer to your phone's documentation for the specific steps to enable Bluetooth. 4. Move your phone close to the watch, within one meter. 5. Press and hold the (C) button on the watch for about three seconds until the e and [CNCT] icons start flashing on the display. 6. Wait for the connection to be established. Once the connection is successful, the e and [CNCT] icons will stop flashing. To disconnect the watch from your phone, simply press any button on the watch, and it will return to the Timekeeping Mode. If you encounter any issues during the connection process, make sure G-SHOCK Connected is running on your phone, and try restarting your phone or disabling and re-enabling Bluetooth. Please note that these steps are general guidelines, and for more detailed instructions, refer to the manual provided with your Casio 3461 smartwatch.

Why is my Casio 3461 smartwatch not charging?

If your Casio 3461 smartwatch is not charging, there could be a few reasons for this issue. Follow these steps to troubleshoot the problem: 1. Check the charging cable: Ensure that the charging cable is securely connected to both the watch and the power source. Make sure there are no loose connections or damage to the cable. 2. Clean the charging contacts: Use a soft, lint-free cloth to clean the charging contacts on both the watch and the charging cable. Dust, dirt, or debris on the contacts can interfere with the charging process. 3. Verify the power source: Ensure that the power source you are using is working properly. Try connecting the charging cable to a different power outlet or USB port to rule out any issues with the power source. 4. Restart the watch: Sometimes, a simple restart can resolve charging issues. Restart your Casio 3461 smartwatch by turning it off and then turning it back on. 5. Contact customer support: If the above steps do not resolve the issue, it is recommended to contact Casio customer support for further assistance. They can provide specific troubleshooting steps or arrange for repair if necessary. Please note that these steps are general guidelines, and for more detailed instructions, refer to the manual provided with your Casio 3461 smartwatch.

How do I set up the world time feature on my Casio 3461 smartwatch using the mobile link?

To set up the world time feature on your Casio 3461 smartwatch using the mobile link, follow these steps: 1. Ensure that your watch is connected to your phone using the mobile link feature. Refer to the manual for instructions on how to establish the connection. 2. Enter the World Time Mode on your watch. This mode allows you to look up the current time in different cities around the world. 3. Use the navigation buttons on your watch to select the World Time number whose setting you want to configure. 4. Hold down the (A) button for about two seconds until [WT] flashes on the display. 5. Use the navigation buttons to display the city you want to assign to the World Time number. 6. If you want to change the summer time setting, press the (C) button. 7. Use the navigation buttons to select a summer time setting. Each press of the navigation button cycles through the available settings, such as [AUTO], [OFF], and [ON]. 8. Press the (A) button to exit the setting screen and save your changes. Please note that these steps are general guidelines, and for more detailed instructions, refer to the manual provided with your Casio 3461 smartwatch.

Is the manual of the Casio 3461 available in English?

Yes, the manual of the Casio 3461 is available in English .

Is your question not listed? Ask your question here

No results