to preset points (start point, destination, etc.).
Navigation indicator of point
Linear distance
Note
●
The message [- - -.-km] will appear if
the current linear distance to the
destination is 1,000 km or greater.
Returning to a Start Point
(Backtrack)
At any time during a navigation operation, you
can reverse your route to navigate back to
your start point.
Destination
Start point
Start point
Current location
1.
While a navigation operation is in
progress, press (D).
Rotary Switch
2.
Rotate the rotary switch to move the
pointer to [BACKTRACK].
3.
Press the rotary switch.
Pressing the rotary switch again or
allowing 10 seconds to elapse after step
3 will change to navigation with your start
point as your new destination.
●
To cancel the route reversal, press (C)
within 10 seconds after pressing the
rotary switch in step 3.
Stopping Navigation
1.
While a navigation operation is in
progress, press (D).
Rotary Switch
2.
Rotate the rotary switch to move the
pointer to [QUIT].
3.
Press the rotary switch.
Pressing the rotary switch again or
allowing 10 seconds to elapse after step
3 will quit navigation and return to the
Timekeeping Mode.
●
To cancel the navigation quit operation,
press (C) within 10 seconds after
pressing the rotary switch in step 3.
Deleting a Destination
Deleting the destination will stop route
guidance, but continue route recording.
●
For information about setting a destination,
refer to the information below.
l
Setting a Registered Point as the
Destination
1.
While a navigation operation is in
progress, press (D).
Rotary Switch
2.
Rotate the rotary switch to move the
pointer to [RESET GOAL].
3.
Press the rotary switch.
This deletes the destination and returns to
the navigation screen.
Note
●
Backtrack cannot be used to clear a
destination while a navigation
operation is in progress.
l
Returning to a Start Point
(Backtrack)
Registering Your Current
Location
You can use the procedure below to record
your current location in Point Memory. A point
recorded in Point Memory can be specified as
the destination for future navigation
operations.
●
Point Memory can store up to 60 points.
1.
While a navigation operation is in
progress, hold down the rotary switch for
about one second.
After you record your location, the display
will momentarily shows its latitude and
longitude, and other information. After a
few seconds, the message [SET ICON?]
will appear.
Operation Guide 3452
14
View the manual for the Casio 3452 here, for free. This manual comes under the category smartwatch and has been rated by 1 people with an average of a 6.9. This manual is available in the following languages: English. Do you have a question about the Casio 3452 or do you need help? Ask your question here
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Casio 3452 below.
Does a smartwatch have functionalities that a smartphone does not have?
In general, a smartwatch has no functionalities that a smartphone does not have.
Do I need to switch off my smartwatch at night?
It is sensible for you to switch off your smartwatch at night, this ensures longer battery life.
Do I need internet for GPS?
No, no internet is required to receive GPS.
What does the abbreviation GPS stand for?
The abbreviation GPS stands for 'Global Positioning System'.
What is GPS?
GPS is a system that can be used all over the globe to determine your location by means of satellites.
What is bluetooth?
Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.
Is the manual of the Casio 3452 available in English?
Yes, the manual of the Casio 3452 is available in English .
Need help?
Do you have a question about the Casio and is the answer not in the manual?
Question and answer
Number of questions: 0