Casio 3031 manual

Casio 3031
9.2 · 1
PDF manual
 · 4 pages
English
manualCasio 3031
2

Operation Guide 3031

To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
SIG).
2. Press A to toggle it on and off.
The Hourly Time Signal on indicator (
) is shown on
the display in all modes while this function is turned on.
5. Press A to exit the setting screen.
Alarm Operation
The alarm tone sounds at the preset time for 20 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, until you turn the alarm off.
Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode time.
To stop the alarm tone after it starts to sound, press any button.
Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the
SNZ
setting screen
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
Turning on a alarm (
SNZ, AL1, AL2, AL3, or
AL4) displays the alarm on indicator ( , , , ,
or
).
In all modes, the alarm on indicator is shown for alarm
that is currently turned on.
The alarm on indicator flashes while the alarm is
sounding.
The snooze alarm indicator (
) flashes while the
snooze alarm is sounding and during the 5-minute intervals
between alarms.

Alarms

You can set up to five independent multi-function alarms
with hour, minutes, month, and day. When an alarm is
turned on, the alarm tone sounds when the alarm time is
reached. One of the alarms is a snooze alarm, while the
other four are one-time alarms.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
There are five alarm screens numbered
AL1, AL2,
AL3, and AL4 for the one-time alarm, a snooze
alarm screen indicated by
SNZ. The Hourly Time
Signal screen is indicated by
SIG.
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
To specify a countdown start time of 24 hours, set
.
4. Press A to exit the setting screen.
You can also perform steps 1 and 2 of the above procedure whenever you need to
view the current auto-repeat and progress beeper settings.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the
countdown timer.
The countdown timer operation continues even if you
exit the Countdown Timer Mode.
Press D while a countdown operation is in progress to
pause it. Press D again to resume the countdown.
To stop a countdown operation completely, first pause it
(by pressing D), and then press B. This returns the
countdown time to its starting value.

Countdown Timer

The countdown timer can be set within a range of one
minute to 24 hours. An alarm sounds when the countdown
reaches zero. The countdown timer also has an auto-
repeat feature and a progress beeper that signals the
progress of the countdown.
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Configuring the Countdown Timer
The following are the settings you should configure before
actually using the countdown timer.
Countdown start time; Auto-repeat on/off; Progress
beeper on/off
See To configure the countdown timer for information
about setting up the timer.
Seconds
Hours
Minutes
Setting
Hours, Minutes
Auto-repeat
Progress Beeper
Screen Button Operation
Use D (+) and B () to change the setting.
Press D to toggle auto-repeat on ( displayed) and off
( displayed).
Press D to toggle the progress beeper on ( ) and off ( ).
Alarm time
(Hour : Minutes)
Alarm number
Alarm on indicator
Alarm date
(Month – Day)
Alarm Types
The alarm type is determined by the settings you make, as described below.
Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at the time you set, only during the month you set.
Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
To set an alarm time
1. In the Alarm Mode, use D or B to scroll through the
alarm screens until the one whose time you want to set
is displayed.
To set a one-time alarm, display an alarm screen AL1, AL2, AL3, or AL4.
To set the snooze alarm, display the
SNZ screen.
The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
This operation turns on the alarm automatically.
3. Press C to move the flashing in the sequence shown below to select other settings.
Hour Minutes Month Day
4. While a setting is flashing, use D and B to change it as described below.
Screen To do this:
Change the hour
and minutes
Change the
month and day
Do this:
Use D (+) and B ().
With the 12-hour format, set the time correctly as a.m.
or p.m. (P indicator).
To set an alarm that does not include a month and/or
day, set for each setting.
Snooze alarm
indicator
Hourly time signal
on indicator
Auto-repeat
When auto-repeat is turned on, the countdown restarts automatically from the
countdown start time when it reaches zero.
When auto-repeat is turned off, the countdown stops when it reaches zero and the
display shows the original countdown start time.
Pressing D while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing D, or you can
press A to reset to the countdown time starting value.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
When the progress beeper is turned off, the countdown end beeper sounds for
about 10 seconds, or until you press any button to stop it.
When the progress beeper is turned on, the countdown end beeper sounds for
about one second.
Progress Beeper
When the progress beeper is turned on, the watch uses beeps to signal countdown
progress as described below.
Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
30 seconds before the end of the countdown, the watch emits four short beeps.
The watch emits a short beep for each of the last 10 seconds of the countdown.
If the countdown start time is six minutes or greater, the watch emits a short beep for
each second of the final 10 seconds before the five-minute point is reached. Four
short beeps are emitted to signal when the five-minute point is reached.
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
If the countdown start time is not displayed, use the
procedure under To use the countdown timer to
display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Hours
Progress Beeper
Minutes
Auto-repeat
3. When the setting you want to change is flashing, use B and D to change it as
described below.

Manual

View the manual for the Casio 3031 here, for free. This manual comes under the category watches and has been rated by 1 people with an average of a 9.2. This manual is available in the following languages: English. Do you have a question about the Casio 3031 or do you need help? Ask your question here

Need help?

Do you have a question about the Casio and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Casio 3031 specifications

Below you will find the product specifications and the manual specifications of the Casio 3031.

The Casio 3031 is a wristwatch that offers a range of features and functions. With its durable and rugged design, it is suitable for various activities and environments. The watch features a digital display that shows the time, date, and day of the week. It also includes an alarm function, allowing users to set reminders and wake up on time. The Casio 3031 is water-resistant, protecting it from damage caused by splashes or brief immersion in water. Additionally, the watch offers a stopwatch function, allowing users to time themselves during various activities. The Casio 3031 also includes a countdown timer, useful for tracking intervals or countdowns. With its clear and easy-to-read display, the watch ensures that information is easily accessible at a glance. The Casio 3031 operates on battery power, providing long-lasting usage before requiring a replacement. It features a lightweight design, making it comfortable to wear for extended periods. The watch also comes with a durable strap that securely fastens to the wrist. In conclusion, the Casio 3031 offers a range of practical features in a durable and reliable package. Its water-resistant design, along with its stopwatch and alarm functions, make it suitable for various outdoor activities and everyday use.

General
BrandCasio
Model3031
Productwatch
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Casio 3031 below.

A battery in my watch has started to corrode. Is the device still safe to use?

The product can still be used safely after proper cleaning. Remove the battery with gloves and clean the battery compartment with a toothbrush and vinegar. After drying, new batteries can be inserted into the device.

How can I turn off the button operation tone on my Casio 3031 watch?

To turn off the button operation tone on your Casio 3031 watch, follow these steps: 1. Make sure you are not on a setting screen. If you are, exit the setting screen. 2. Press and hold the C button. This will toggle the button operation tone on or off. 3. When the button operation tone is turned off, the MUTE indicator will be displayed in all modes. 4. Release the C button. Please note that even if you turn off the button operation tone, the alarms, hourly time signal, countdown alarm, and stopwatch auto start will still operate normally. By following these steps, you can easily turn off the button operation tone on your Casio 3031 watch.

Why are the alarms, hourly time signal, countdown alarm, and stopwatch auto start affected by the button operation tone on my Casio 3031 watch?

The alarms, hourly time signal, countdown alarm, and stopwatch auto start on your Casio 3031 watch are affected by the button operation tone for the following reasons: 1. The button operation tone is a sound that is produced whenever you press one of the watch's buttons. It serves as an audible feedback for button presses. 2. When you turn off the button operation tone, it also affects the alarms, hourly time signal, countdown alarm, and stopwatch auto start. However, these functions will still operate normally even with the button operation tone turned off. 3. The purpose of this design is to provide a silent operation for the watch, especially in situations where the button operation tone may be disruptive or unwanted, such as during meetings or in quiet environments. By turning off the button operation tone, you can ensure that the alarms, hourly time signal, countdown alarm, and stopwatch auto start functions on your Casio 3031 watch operate silently.

How does the automatic return feature work on my Casio 3031 watch?

The automatic return feature on your Casio 3031 watch works as follows: 1. If you leave the watch in the Alarm Mode for two or three minutes without performing any operation, it automatically changes to the Timekeeping Mode. 2. Similarly, if you leave a screen with flashing digits on the display for two or three minutes without performing any operation, the watch automatically exits the setting screen. The purpose of the automatic return feature is to ensure that the watch returns to the Timekeeping Mode or exits the setting screen when left idle for a certain period of time. This helps conserve battery life and prevents accidental changes to settings. By understanding how the automatic return feature works, you can use your Casio 3031 watch more efficiently and avoid unintended mode changes or settings adjustments.

Why does my Casio 3031 watch automatically change to the Timekeeping Mode when left in the Alarm Mode for a certain period of time?

Your Casio 3031 watch automatically changes to the Timekeeping Mode when left in the Alarm Mode for a certain period of time due to the following reasons: 1. The Alarm Mode is designed for setting and managing alarms on your watch. 2. When you enter the Alarm Mode and perform the desired alarm settings, the watch expects you to complete the necessary operations and exit the mode. 3. However, if you leave the watch in the Alarm Mode without performing any further operations for a specific duration (usually around two or three minutes), the watch assumes that you have finished setting the alarms and automatically switches back to the Timekeeping Mode. This automatic change to the Timekeeping Mode helps ensure that the watch returns to its default mode after a period of inactivity, preventing accidental changes to alarm settings and conserving battery life. By understanding this functionality, you can effectively manage your Casio 3031 watch's modes and ensure that it operates as intended.

How do I scroll through data on the display of my Casio 3031 watch using the B and D buttons?

To scroll through data on the display of your Casio 3031 watch using the B and D buttons, follow these steps: 1. In various modes and setting screens, the B and D buttons are used to scroll through data on the display. 2. Press the B button to scroll through the data in one direction, such as moving from one option to the next or scrolling through a list. 3. Press the D button to scroll through the data in the opposite direction, allowing you to navigate back or move to the previous option. 4. In most cases, holding down the B or D button during a scroll operation will increase the scrolling speed, allowing you to quickly move through the data. By using the B and D buttons, you can easily navigate and scroll through the data displayed on your Casio 3031 watch, whether it's selecting options, viewing lists, or moving between different screens.

How can I scroll at high speed through data on my Casio 3031 watch?

To scroll at high speed through data on your Casio 3031 watch, follow these steps: 1. Use the B and D buttons to navigate through various modes and setting screens. 2. When you need to scroll through data on the display, press and hold either the B or D button. 3. Holding down the B or D button during a scroll operation will increase the scrolling speed, allowing you to quickly move through the data. 4. Continue holding the button until you reach the desired position or data on the display. By holding down the B or D button, you can scroll at high speed through the data on your Casio 3031 watch. This feature enables efficient navigation and saves time when accessing information or adjusting settings.

Why does my Casio 3031 watch display the last viewed data when entering the World Time or Alarm Mode?

Your Casio 3031 watch displays the last viewed data when entering the World Time or Alarm Mode for the following reasons: 1. The watch is designed to remember the last viewed data in these modes to provide convenience and ease of use. 2. When you exit the World Time or Alarm Mode, the watch stores the information you were viewing, such as the time in different cities or the set alarm times. 3. When you re-enter the World Time or Alarm Mode, the watch automatically displays the last viewed data, allowing you to quickly access the information without having to re-enter it. 4. This feature saves time and effort, especially if you frequently need to refer to the same world time or alarm settings. By displaying the last viewed data, your Casio 3031 watch ensures that you can easily access and reference the information you were previously viewing in the World Time or Alarm Mode, enhancing the user experience and convenience.

How do I reset the seconds on my Casio 3031 watch?

To reset the seconds on your Casio 3031 watch, follow these steps: 1. In the Timekeeping Mode, hold down the A button until the seconds start to flash, indicating that you are in the setting screen. 2. Press the D button to reset the seconds to 00. 3. Press the A button to exit the setting screen and save the changes. By following these steps, you can easily reset the seconds on your Casio 3031 watch. This feature allows you to synchronize the time accurately and ensure that the seconds display starts from zero.

How do I set the year on my Casio 3031 watch?

To set the year on your Casio 3031 watch, follow these steps: 1. In the Timekeeping Mode, hold down the A button until the seconds start to flash, indicating that you are in the setting screen. 2. Press the D button repeatedly to navigate to the year setting. 3. Use the B button to decrease the year or the D button to increase the year until you reach the desired value. 4. After setting the year, press the A button to exit the setting screen and save the changes. By following these steps, you can easily set the year on your Casio 3031 watch. This allows you to keep the watch's date and time accurate and up to date.

How does the built-in full automatic calendar on my Casio 3031 watch work?

The built-in full automatic calendar on your Casio 3031 watch works as follows: 1. The watch automatically adjusts the date, including the day, month, and year, based on the current time and date information. 2. The watch uses the information you set, such as the time, to calculate and display the correct date. 3. The full automatic calendar takes into account the number of days in each month, including leap years, to ensure accurate date display. 4. The watch also considers daylight saving time (DST) adjustments, if applicable, to accurately reflect the current date and time. By relying on the built-in full automatic calendar, you can trust that your Casio 3031 watch will always display the correct date without the need for manual adjustments. This feature provides convenience and ensures that you stay on track with the current date and time.

Is the manual of the Casio 3031 available in English?

Yes, the manual of the Casio 3031 is available in English .

Is your question not listed? Ask your question here

No results