Canon XJ27x6.5B AF Digisuper manual

Canon XJ27x6.5B AF Digisuper
6.2 · 1
PDF manual
 · 136 pages
English
manualCanon XJ27x6.5B AF Digisuper
C2 C3
1 安装与连接

1-2 安装全程伺服配套件

伺服电动控制器的安装和连接方法,如下图所示。安装各种
电动控制器时,请参阅电动控制器的使用说明书。
伺服模块
变焦伺服电动控制器
聚焦伺服电动控制器
电动控制器电缆线

在镜头上安装伺服模块

必须将伺服模块固定于镜头底仓内的变焦和聚焦耦合器上。
※ (须知)
变焦和聚焦耦合器所使用的伺服模块完全相同。因此,伺服模块既可
安装于变焦耦合器上,也可以安装于聚焦耦合器上。
1
在镜头上安装一个模块之前,首先沿着逆时针方向,旋
转模块上的锁定螺钉,直至旋出锁定螺杆的一半为止。
2
沿着箭头 A 所示方向,压按该模块,使镜头上的键全部
插入到模块上的键槽内。
耦合器 B
刻度线
(白线)
箭头 A
键槽
镜头底仓
锁定螺杆
锁定螺钉
伺服模块
耦合器 A
3
吻合地装配模块上的耦合器 A 与镜头的耦合器 B然后,
用全力朝着箭头 B 所示方向推压,直至推不动为止。
4
最后,沿着顺时针方向,旋转和紧固模块上的锁定螺钉。
使用硬币,拧紧锁定钮。
箭头 B
锁定螺钉
锁定
然后,按照相同操作步骤,将伺服模块安装于另一个耦合器上。
变焦或聚焦耦合器,可任意选择先安装其中的某一个。
※ (须知)
连接耦合器 A B 时,应将伺服模块完全推入,从而将耦合器 B
围的刻度线(白线)完全遮蔽。
如果未完全遮蔽刻度线,则将会使伺服模块不能正常运行,并将可能
导致产生异常噪音。

安装开关盒

1
使用连接于开关盒上的箝位器,将其安装于三脚架的摇
摄手柄上。
2
使用附属件中的电缆,连接镜头与开关盒。

Manual

View the manual for the Canon XJ27x6.5B AF Digisuper here, for free. This manual comes under the category lenses and has been rated by 1 people with an average of a 6.2. This manual is available in the following languages: English. Do you have a question about the Canon XJ27x6.5B AF Digisuper or do you need help? Ask your question here

Need help?

Do you have a question about the Canon and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Canon XJ27x6.5B AF Digisuper specifications

Below you will find the product specifications and the manual specifications of the Canon XJ27x6.5B AF Digisuper.

General
BrandCanon
ModelXJ27x6.5B AF Digisuper
Productlens
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Canon XJ27x6.5B AF Digisuper below.

Is the manual of the Canon XJ27x6.5B AF Digisuper available in English?

Yes, the manual of the Canon XJ27x6.5B AF Digisuper is available in English .

Is your question not listed? Ask your question here

No results