Canon Speedlite EL-1 manual

Canon Speedlite EL-1
7.5 · 1
PDF manual
 · 232 pages
English
manualCanon Speedlite EL-1

Modeling Flash

When you press the aperture button on the camera, the flash fires continuously for about 1
second. This function is called "modeling flash". This is useful for checking shadows cast on
the subject by the flash light and the lighting balance during wireless flash shooting ( , ).
1.
Press the depth-of-field preview button on the camera.
The flash fires continuously for approx. 1 sec.
Caution
To avoid degrading and damaging the flash head due to overheating, set the
number of modeling flashes to 55 or less. After firing the modeling flash for the
above listed number of times, allow a rest time of at least 50 minutes.
If you fire the modeling flash for the above listed number of times, and then fire the
flash again repeatedly at short intervals, the safety function will activate and flash
firing restriction will be carried out. When the flash firing restriction level is 1, the
firing interval is automatically set to about 8 seconds. If this happens, allow a rest
time of at least 50 min.
During Live View shooting, firing the modeling flash (by operating the camera) is
not possible.
Modeling flash cannot be fired (by an operation on the camera side) when the flash
is used in combination with the EOS R6, EOS R5, EOS RP, EOS R,
EOS M6 Mark II, EOS M50, EOS M6, EOS M5, EOS M3, EOS M2, EOS M,
EOS Elan II/Elan II E/50/50E, EOS REBEL 2000/300, EOS REBEL G/500N,
EOS REBEL K2/3000V, EOS REBEL XS N/REBEL G II/3000N/66, EOS IX, or
EOS IX Lite/IX7. Set C.Fn-02 to 1 or 2 ( ) and use the test flash button to perform
modeling flash.
Note
During normal flash shooting or when using the flash as the sender unit in radio
transmission / optical transmission wireless shooting, you can fire the modeling
flash with the test flash button (C.Fn-02).
89

View the manual for the Canon Speedlite EL-1 here, for free. This manual comes under the category flash units and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Canon Speedlite EL-1 or do you need help? Ask your question here

Need help?

Do you have a question about the Canon and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

General
BrandCanon
ModelSpeedlite EL-1 | 4571C010
Productflash unit
EAN8714574667881
LanguageEnglish
FiletypeUser manual (PDF)
Weight & dimensions
Width84.4 mm
Depth136.4 mm
Height149 mm
Weight572 g
Features
TypeCompact flash
Product colorBlack
Approximate recycling time- s
Approximate recycling time (min)0.1 s
Approximate recycling time (max)0.9 s
Approx. number of flashes335
DustproofYes
Water-resistantYes
Camera brands compatibilityUniversal
Flash exposure compensationYes
CompatibilityEOS-1D X Mark III\nEOS R5\nEOS 5DS\nEOS 5DS R\nEOS 5D Mark IV\nEOS R6\nEOS R\nEOS Ra\nEOS RP\nEOS 6D Mark II\nEOS 7D II\nEOS 90D\nEOS 850D\nEOS 250D\nEOS 2000D⁶\nEOS 1300D⁶\nEOS 4000D⁶\nEOS M5⁶\nEOS M6 Mark II⁶\nEOS M50⁶\nEOS-1D X Mark II\nPowerShot G1 X Mark III\nPowerShot G3 X\nPowerShot G5 X\nEOS R3
Zoom reflectorYes
Auto Focus (AF) assist beamYes
Focal length range24 - 200 mm
Flash modesHigh-speed synchronization, Manual, Stroboscopic
Power
Number of batteries supported1
Battery typeBuilt-in
Battery technologyLithium-Ion (Li-Ion)
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Canon Speedlite EL-1 below.

What is the weight of the Canon Speedlite EL-1?

The Canon Speedlite EL-1 has a weight of 572 g.

What is the height of the Canon Speedlite EL-1?

The Canon Speedlite EL-1 has a height of 149 mm.

What is the width of the Canon Speedlite EL-1?

The Canon Speedlite EL-1 has a width of 84.4 mm.

What is the depth of the Canon Speedlite EL-1?

The Canon Speedlite EL-1 has a depth of 136.4 mm.

Can the Canon Speedlite EL-1 be used with any camera brand?

Yes, the Canon Speedlite EL-1 is compatible with all camera brands.

Is the Canon Speedlite EL-1 dustproof?

Yes, the Canon Speedlite EL-1 is dustproof, ensuring that it can withstand various environments and maintain optimal performance.

How long does it take for the Canon Speedlite EL-1 to recycle for the next flash?

The Canon Speedlite EL-1 has a minimum recycling time of 0.1 seconds and a maximum recycling time of 0.9 seconds. This fast recycling time allows users to capture multiple shots in quick succession.

Does the Canon Speedlite EL-1 have an Auto Focus (AF) assist beam?

Yes, the Canon Speedlite EL-1 features an Auto Focus (AF) assist beam, providing improved focus accuracy in low light conditions.

How many flashes can the Canon Speedlite EL-1 approximately produce?

The Canon Speedlite EL-1 can produce approximately 335 flashes on a single battery. This high number of flashes allows photographers to continuously shoot without worrying about frequent battery replacements.

How do I properly attach the Canon Speedlite EL-1 flash unit to my EOS camera?

To properly attach the Canon Speedlite EL-1 flash unit to your EOS camera, follow these steps: 1. Ensure that both the flash unit and the camera are powered off before attaching the flash unit. 2. Locate the hot shoe on top of your EOS camera. The hot shoe is a metal bracket with electrical contacts. 3. Align the metal contacts on the bottom of the Canon Speedlite EL-1 flash unit with the contacts on the hot shoe of the camera. 4. Gently slide the flash unit into the hot shoe, making sure it is securely attached. You should feel a click or locking mechanism when it is properly inserted. 5. Once the flash unit is attached, turn on both the camera and the flash unit. 6. Check the camera settings to ensure that the flash is enabled and set to the desired mode (e.g., TTL, Manual, etc.). 7. Test the flash by taking a photo. If the flash fires and provides the desired lighting, it is properly attached and ready to use. Remember to consult the Canon Speedlite EL-1 flash unit manual for more detailed instructions and information on specific camera models.

Why is the Canon Speedlite EL-1 flash unit not turning on when I press the power button?

If the Canon Speedlite EL-1 flash unit is not turning on when you press the power button, you can try the following troubleshooting steps: 1. Check if the battery compartment cover is closed properly. Make sure it is securely closed. 2. Replace the batteries with new ones. Ensure that the batteries are inserted correctly and have enough charge. 3. Insert the mounting foot of the flash unit into the camera's hot shoe fully. Slide the lock lever to the right to secure the Speedlite to the camera. 4. If the "< >" indication remains displayed for approximately 15 seconds or longer, replace the batteries. 5. Check if the electrical contacts of the Speedlite or camera are dirty. Use a dry cloth to wipe the contacts and ensure they are clean. 6. If you have been using continuous firing repeatedly over a short period of time, the flash head's temperature may have risen, causing flash firing to be restricted. In this case, the firing interval increases. 7. If the Speedlite's auto power off feature has been activated, press the shutter button halfway or press the test flash button to reactivate the power. If the issue persists, it is recommended to refer to the Canon Speedlite EL-1 flash unit manual or contact your nearest Canon Service Center for further assistance.

What should I do if the Canon Speedlite EL-1 flash unit is not firing when I take a photo?

If the Canon Speedlite EL-1 flash unit is not firing when you take a photo, you can try the following troubleshooting steps: 1. Check if the battery compartment cover is closed properly. Ensure that it is securely closed. 2. Replace the batteries with new ones to ensure they have enough charge. 3. Insert the mounting foot of the flash unit into the camera's hot shoe fully. Slide the lock lever to the right to secure the Speedlite to the camera. 4. If the "< >" indication remains displayed for approximately 15 seconds or longer, replace the batteries. 5. Check if the electrical contacts of the Speedlite or camera are dirty. Use a dry cloth to wipe the contacts and ensure they are clean. 6. If you have been using continuous firing repeatedly over a short period of time, the temperature of the flash head may have risen, causing flash firing to be restricted. In this case, the firing interval increases. 7. If the internal temperature of the battery attached to the charger is high, the charger will not charge the battery for safety reasons. Charging will stop automatically. When the battery temperature goes down, charging will resume automatically. If the issue persists, it is recommended to refer to the Canon Speedlite EL-1 flash unit manual or contact your nearest Canon Service Center for further assistance.

How can I troubleshoot if the Canon Speedlite EL-1 flash unit is not communicating wirelessly with my camera or other devices?

To troubleshoot if the Canon Speedlite EL-1 flash unit is not communicating wirelessly with your camera or other devices, follow these steps: 1. Check the wireless settings on both the flash unit and the camera. Ensure that the radio transmission or optical transmission wireless settings are properly configured. 2. Verify that the sender and receiver settings are correctly set. Use the joystick or navigation buttons to access the settings menu and select the appropriate options for the sender and receiver units. 3. Set the transmission channel or wireless radio ID. This helps ensure that the flash unit and the camera are using the same channel or ID for wireless communication. 4. Check the flash firing settings on the sender unit. Make sure that the flash firing is enabled and not turned off. 5. Utilize the memory function if available. This allows you to save and recall specific wireless settings for future use. 6. Ensure that the E-TTL II or E-TTL mode is selected for autoflash photography during wireless shooting. If the issue persists, refer to the Canon Speedlite EL-1 flash unit manual for more detailed troubleshooting steps or contact Canon customer support for further assistance.

Why is the Canon Speedlite EL-1 flash unit not providing the desired lighting or exposure in my photos?

If the Canon Speedlite EL-1 flash unit is not providing the desired lighting or exposure in your photos, you can try the following troubleshooting steps: 1. Check the flash mode settings on the flash unit. Ensure that the appropriate mode is selected for your shooting conditions, such as E-TTL II, Manual, or Multi-flash mode. 2. Adjust the flash output level. Increase or decrease the flash output to achieve the desired lighting. Use the flash exposure compensation function if available to fine-tune the exposure. 3. Verify the flash coverage. Ensure that the flash head is properly positioned and adjusted for the desired coverage. Consider using a diffuser or bounce adapter to modify the light spread. 4. Check the camera settings. Ensure that the camera's exposure settings, such as aperture, shutter speed, and ISO, are properly configured to work with the flash unit. 5. Consider using additional accessories. Attach color filters, bounce cards, or diffusers to modify the light and achieve the desired lighting effects. 6. Test different shooting distances. Experiment with different distances between the subject and the flash unit to find the optimal lighting and exposure. If the issue persists, refer to the Canon Speedlite EL-1 flash unit manual for more detailed troubleshooting steps or contact Canon customer support for further assistance.

Is the manual of the Canon Speedlite EL-1 available in English?

Yes, the manual of the Canon Speedlite EL-1 is available in English .

Is your question not listed? Ask your question here

No results