Canon P1-DTSC II manual

Canon P1-DTSC II
8.5 · 2
PDF manual
 · 2 pages
English
manualCanon P1-DTSC II

CÁLCULO CON DECIMALES

Tecla Decimal Point Selector – permite designar la posición del punto
decimal (F, 0, 2, 3, 4, A) para los resultados calculados.
A (Add-Mode) – las funciones de suma y resta se realizan con un decimal
automático de 2 dígitos. Esto es práctico para los cálculos de conversión.
F (Floating Decimal point) – se imprimen o se muestran todos los números
efectivos con un máximo de 12 dígitos. (no se muestra el icono "F")
Tecla Rounding – permite redondear al alza [ ], redondear al entero más
próximo [5/4], o redondear a la baja [ ] a los dígitos decimales
preseleccionados en el resultado.

FUNCIONES IMPORTANTES A RECORDAR

Tecla On/Clear / Off permite encender la calculadora.
Al realizar un cálculo, púlsela una vez para borrar el último valor introducido.
Púlsela de nuevo para borrar todos los valores introducidos, excepto la
memoria. Esta tecla también se utiliza para borrar el error de desbordamiento.
Manténgala pulsada durante 2 segundos para apagar la calculadora.
Tecla Print On/Off

permite activar y desactivar la impresora.

Cuando aparece la marca "PRINT" en la pantalla, las entradas y los
resultados aparecerán en la pantalla y se imprimirán.
Cuando no aparece la marca "PRINT" en la pantalla, las entradas y los
resultados aparecerán en la pantalla, pero no se imprimirán.
Tecla Business / Tax Function

permite alternar entre el cálculo financiero

o de impuestos.
Tecla Paper Feed

permite que avance el papel.

Tecla Rate Set

permite establecer la tasa de impuesto o la tasa de cambio

de divisas.
Tecla Memory / Currency Function

permite alternar entre el cálculo de

conversión de divisas o memoria.
Tecla Non-Add

permite imprimir información que no afecta al cálculo, como

fechas y números de serie. Las figuras se imprimen en la parte izquierda del
papel.
Tecla Equal

permite obtener resultados de suma, resta, multiplicación y

división.

FUNCIÓN DE CÁLCULO DE TIEMPO

Permite calcular la cantidad de tiempo o la duración de actividades, como
la estimación de costes, horas y salarios.
Permite alternar entre AM (se muestra "AM" y se imprime ""),
PM (se muestra "PM" y se imprime " •• ") o 24 horas (no se muestra ni se
imprime ningún icono) en el modo de cálculo de tiempo.
** Valor de entrada de minutos: de 0 a 59. Los valores superiores a 59 se ajustan
automáticamente mediante la adición de hora(s).
**
Rango de cálculo: de –99 horas y 59 minutes a 99 horas y 59 minutos. Si el valor de
entrada/salida se encuentra fuera del rango permitido, el cálculo de tiempo se desbordará.

CÁLCULO DE CONVERSIÓN DE DIVISAS

Pulse para convertir la cantidad de dinero mostrada de a o
.
Pulse o para convertir la cantidad mostrada de o a .
Para tasas de 1 o superiores, puede introducir hasta 6 dígitos. Para tasas inferiores a 1,
puede introducir hasta 8 dígitos (p.ej., 0,1234567), incluyendo 0 para el dígito entero y
ceros iniciales (aunque solo se pueden especificar 7 dígitos significativos, contados
desde la izquierda y comenzando con el primer dígito distinto de cero).

FUNCIÓN DE CÁLCULO DE IMPUESTOS

Tecla Add tax – permite añadir el importe del impuesto a la cantidad
mostrada.
Tecla Deduct Tax – permite deducir el importe del impuesto a la cantidad
mostrada.
Nota: La tasa de impuesto introducida quedará almacenada incluso cuando se apague la
calculadora. Sin embargo, la tasa introducida se eliminará una vez se desconecte el
enchufe. En este caso, vuelva a introducir la tasa.

CÁLCULO DE COSTE-VENTA-MARGEN

Permite calcular la cantidad del coste, precio de venta, margen de beneficio y
valor del margen. Introduzca el valor de cualesquiera 2 elementos para obtener
el elemento de valor de equilibrio. (p.ej., introduzca el valor del coste y el precio
de venta para obtener el porcentaje del margen de beneficio).

FUNCIÓN DE DOBLE VERIFICACIÓN

Permite iniciar el proceso de verificación de registro. "CHE" aparecerá en la
pantalla.
Permite iniciar un proceso de verificación. El proceso de verificación compara la
entrada del usuario con la anterior cola de operaciones registrada. "CHE StArt"
aparecerá en la pantalla.
El ajuste de los interruptores debe coincidir con la primera y segunda entrada de
operaciones. Si los interruptores no coinciden, se imprimirá el siguiente mensaje.
* ••001•• – El valor del punto decimal es diferente
* ••002•• – El valor del redondeo es diferente
Esta calculadora cuenta con una cola de operaciones de 100 pasos, que resulta útil para
el proceso de verificación. Si se encuentra fuera de la cola de operaciones, no se le
permitirá acceder a la función de doble verificación y el mensaje "E CHE St FULL"
aparecerá en la pantalla.
En la primera entrada, pulse la tecla para finalizar el cálculo que se desea
verificar. Se imprimirá ",,.,.,,".
En la segunda entrada, pulse la tecla para cancelar el proceso de verificación. Se
imprimirá "••000••".

FUNCIÓN DE DESBORDAMIENTO

En los siguientes casos, cuando aparece una “E”, se imprime una línea de puntos, el
teclado se bloquea electrónicamente y es imposible realizar más operaciones. Pulse
para borrar el desbordamiento. El desbordamiento ocurre en los siguientes casos:
1) El resultado o el contenido de memoria supera los 12 dígitos a la izquierda del punto
decimal.
2) División por "0".
3) La velocidad de operación secuencial es superior a la de procesamiento del cálculo.
(Desbordamiento del registro del búfer)

ESPECIFICACIONES

Temperatura de funcionamiento: de 0 ºC a 40 ºC
Apagado automático: aprox. 7 minutos
Dimensiones: 196mm (L) x 99mm (An.) x 40mm (Al.)
Peso: 304 g con baterías / 234 g sin baterías
(Sujeto a cambios sin previo aviso)

ESPOL

CALCOLI CON I NUMERI DECIMALI

Tasto di selezione della virgola decimale – consente di definire la
posizione della virgola decimale (F, 0, 2, 3, 4, A) per i risultati dei calcoli.
A (Add-Mode) – consente di eseguire addizioni e sottrazioni con 2 cifre
decimali impostate in maniera automatica. Si tratta di una modalità utile per i
calcoli legati alle valute.
F (floating point) – vengono visualizzati i numeri composti da fino a 12 cifre
(non viene visualizzata l'icona "F").
Tasto di arrotondamento – consente di eseguire arrotondamento per
eccesso [ ], approssimazione [5/4] o arrotondamento per difetto [ ]
utilizzando le cifre decimali preselezionate nel risultato.

FUNZIONI IMPORTANTI DA RICORDARE

Tasto On/Clear / Off – consente di accendere la calcolatrice.
Durante l'esecuzione di un calcolo, la singola pressione di questo tasto
consente di cancellare l'ultimo valore inserito. Premendo di nuovo il tasto sarà
possibile cancellare tutti i valori inseriti, con l'esclusione di quelli in memoria. Il
tasto consente anche di cancellare l'errore di overflow. Tenere premuto il tasto
per 2 secondi per spegnere la calcolatrice.
Tasto Print On/Off – consente di accendere e spegnere la stampante.
Se sul display è presente l'indicazione "PRINT", le voci e i risultati verranno
visualizzati sullo schermo e sulla carta.
Se sul display non è presente l'indicazione "PRINT", le voci e i risultati
verranno visualizzati sullo schermo ma non sulla carta.
Tasto Business / Tax Function – consente di alternare il calcolo delle
imposte e funzioni aziendali.
Tasto Paper Feed – fa avanzare la carta.
Tasto Rate Set – consente di definire il tasso delle imposte o del cambio
valuta.
Tasto Memory / Currency Function – consente di alternare il calcolo delle
conversioni di valuta e della memoria.
Tasto Non-Add – consente di stampare informazioni estranee al calcolo,
come ad esempio date e serie numeriche. Le cifre vengono stampate sul lato
sinistro della carta.
Tasto "uguale" – consente di ottenere i risultati delle operazioni di addizione,
sottrazione, moltiplicazione e divisione.

FUNZIONE DI CALCOLO DEL TEMPO

Consente di calcolare il quantitativo di tempo (o la durata) delle attività, come
ad esempio per la stima dei costi e delle retribuzioni orarie.
Consente di alternare l'orario antimeridiano o AM (viene visualizzato "AM" e
stampato "•"), postmeridiano o PM (viene visualizzato "PM" e stampato "••") e
24 ore (non vengono visualizzate e stampate icone) in modalità di calcolo
dell'ora.
** Valore dei minuti che è possibile immettere: da 0 a 59. I valori superiori a 59 vengono
automaticamente arrotondati aggiungendoli al conteggio delle ore.
** Intervallo di calcolo: da -99 ore e 59 minuti a 99 ore e 59 minuti. Se il valore di immissione o
uscita dovesse cadere fuori dall'intervallo consentito, il calcolo del tempo produrrà un
overflow.

CALCOLO DELLA CONVERSIONE DELLA VALUTA

Premere per convertire la valuta visualizzata da a o .
Premere o per convertire i valori visualizzati da o a .
Per tassi pari a 1 o superiori è possibile inserire fino a 6 cifre. Per tassi inferiori a 1 è
possibile inserire fino a 8 cifre (es. 0,1234567), compreso lo 0 per le cifre intere e gli zeri
iniziali, anche se è possibile specificare solo 7 cifre significative, iniziando a contare da
sinistra e partendo dalla prima cifra diversa da zero.

FUNZIONE DI CALCOLO DELLE IMPOSTE

Tasto Add Tax – consente di aggiungere l'importo dell'imposta alla cifra
visualizzata.
Tasto Deduct Tax
consente di dedurre l'importo dell'imposta dalla cifra
visualizzata.
Nota: il tasso delle imposte immesso resterà memorizzato anche dopo lo spegnimento
della calcolatrice. Il tasso immesso verrà eliminato scollegando l'alimentazione
elettrica, caso in cui occorrerà immetterlo di nuovo.

CALCOLO COSTO/VENDITA/MARGINE

Consente di calcolare il costo, il prezzo di vendita, il margine di profitto e l'importo
del margine. Inserire il valore di 2 elementi qualsiasi per ottenere l'elemento del
valore di saldo (es. inserire il valore del costo e del prezzo di vendita per ottenere
il margine percentuale del profitto).

FUNZIONE DI CONTROLLO DOPPIO

Consente di avviare il processo di controllo dati. Sullo schermo verrà visualizzata
la scritta "CHE".
Consente di avviare il processo di controllo, che confronta i dati inseriti dall'utente
con la coda delle operazioni registrate in precedenza. Sullo schermo verrà
visualizzata la scritta "CHE StArt".
L'impostazione dei commutatori nella prima e seconda immissione dell'operazione deve
essere uguale. In caso di mancata corrispondenza degli interruttori verrà stampato il seguente
messaggio.
* ••001••: impostazione differente della virgola decimale
* ••002••: impostazione differente dell'arrotondamento
La calcolatrice è dotata di una coda di 100 operazioni, funzione utile per il processo di
controllo. Una volta esaurita la coda delle operazioni sarà impossibile attivare la funzione
di controllo doppio e sullo schermo verrà visualizzato il messaggio "E CHE St FULL".
Al momento della prima immissione, premere il tasto per terminare il calcolo di
controllo. Verrà stampata la stringa ",,.,.,,".
Al momento della seconda immissione, premere il tasto per annullare il processo di
controllo. Verrà stampata la stringa "••000••".
FUNZIONE DI OVERFLOW
Nei seguenti casi, in presenza della lettera "E" su schermo, viene stampata una linea
tratteggiata, bloccata la tastiera a livello elettronico e impedita qualsiasi operazione.
Premere per cancellare l'overflow, una condizione che si verifica nei seguenti casi:
1) Il risultato o il contenuto della memoria superano 12 cifre a sinistra della virgola
decimale.
2) Viene eseguita una divisione per 0.
3) La velocità delle operazioni sequenziali è superiore a quella dell'elaborazione dei calcoli
(overflow del registro del buffer).

SPECIFICHE

Temperatura operativa: da 0 ºC a 40 ºC
Spegnimento automatico: dopo circa 7 minuti
Dimensioni: 196 mm (L) x 99 mm (A) x 40 mm (P)
Peso: 304 g con le batterie / 234 g senza batterie
(soggetto a cambiamento senza alcun avvertimento)

ITALIANO

REKENEN MET DECIMALEN

Selectietoets voor decimaalteken – wordt gebruikt om de positie van het
decimaalteken toe te wijzen (F, 0, 2, 3, 4, A) voor de resultaten van een
berekening.
A (optelmodus) – optel- en aftrekfuncties worden uitgevoerd met een
automatisch decimaal getal van 2 cijfers. Dit is handig voor
valutaberekeningen.
F (zwevendekommagetal) – alle effectieve nummers van maximaal 12 cijfers
worden afgedrukt of weergegeven. (er wordt geen 'F'-pictogram
weergegeven)
Afrondingstoets – wordt gebruikt voor omhoog afronden [ ], omlaag
afronden [5/4] of omlaag afronden [ ] tot het vooraf geselecteerde aantal
decimalen in het resultaat.

BELANGRIJKE FUNCTIES

Toets On/Clear / Off – wordt gebruikt om de rekenmachine in te schakelen.
Wanneer u een berekening uitvoert, drukt u eenmaal op deze toets om de
laatst ingevoerde waarde te wissen. Druk nogmaals op deze toets om alle
ingevoerde waarden te wissen, met uitzondering van de waarden in het
geheugen. Deze toets wordt ook gebruikt om de overloopfout te wissen. Houd
de toets twee seconden ingedrukt om de rekenmachine uit te schakelen.
Toets Print On/Off – wordt gebruikt om de printer in en uit te schakelen.
Wanneer op het scherm de markering 'PRINT' wordt weergegeven, worden
invoer en resultaten op het scherm weergegeven en afgedrukt.
Wanneer de markering 'PRINT' niet op het scherm wordt weergegeven,
worden invoer en resultaten wel op het scherm weergegeven, maar niet
afgedrukt.
Toets Business / Tax Function – wordt gebruikt om te wisselen tussen
zakelijke berekeningen en belastingberekeningen.
Toets Paper Feed – wordt gebruikt om het papier in te voeren.
Toets Rate Set – wordt gebruikt om het belastingtarief of de valutakoers in te
stellen.
Toets Memory / Currency Function – wordt gebruikt om te wisselen tussen
een berekening met waarden in het geheugen en een valutaconversie.
Toets Non-Add – wordt gebruikt om informatie af te drukken die geen invloed
heeft op de berekening, zoals datums en serienummers. Afbeeldingen worden
op de linkerzijde van het papier afgedrukt.
Toets Equal: wordt gebruikt voor het verkrijgen van de resultaten van
optellen, aftrekken, vermenigvuldigen en delen.

TIJDBEREKENING

Wordt gebruikt om de tijd of duur van activiteiten te berekenen, zoals
loonuren en kostenberamingen.
Wordt gebruikt om bij de berekening van de tijd te wisselen tussen AM
('AM' wordt weergegeven en '•' wordt afgedrukt), PM ('PM' wordt
weergegeven en '••' wordt afgedrukt) of 24 uur (er wordt geen
pictogram weergegeven of afgedrukt).
** nvoerwaarde in minuten: 0 tot 59. Waarden boven 59 worden automatisch aangepast en
aan de uren toegevoegd.
** Rekenbereik: van -99 uur en 59 minuten tot 99 uur en 59 minuten. Als de
invoer-/uitvoerwaarde buiten het toegestane bereik valt, loopt de tijdberekening over.

BEREKENING VALUTACONVERSIE

Druk op om het valutagetal dat wordt weergegeven van te
converteren naar of .
Druk op of om het weergegeven getal van of naar te
converteren.
Voor koersen van 1 of hoger kunt u maximaal 6 cijfers invoeren. Voor koersen die
lager zijn dan 1 kunt u maximaal 8 cijfers invoeren (bijv. 0,1234567), inclusief 0 voor het
gehele getal en voorloopnullen (u kunt echter maximaal 7 significante cijfers opgeven,
geteld vanaf links en beginnend met het eerst cijfer dat geen nul is).

FUNCTIE VOOR BELASTINGBEREKENING

Toets Add Tax – wordt gebruikt om het belastingbedrag bij het weergegeven
getal op te tellen.
Toets Deduct Tax –wordt gebruikt om het belastingbedrag van het
weergegeven getal af te trekken.
Pmerking:
het ingevoerde belastingtarief blijft opgeslagen, zelfs als de rekenmachine
wordt uitgeschakeld. Het ingevoerde tarief wordt echter wel verwijderd als u de
stekker uit het stopcontact haalt. In dit geval moet u het tarief opnieuw invoeren.

BEREKENING KOSTEN/VERKOOP/MARGE

Wordt gebruikt om de kosten, verkoopprijs, winstmarge en waarde van de marge
te berekenen. Voer de waarde in van twee willekeurige items om de
balanswaarde te verkrijgen. (bijv.: voer de waarde van de kosten en de
verkoopprijs in om de winstmarge in procenten te verkrijgen.)

FUNCTIE VOOR DUBBEL CONTROLEREN

Wordt gebruikt om het controleproces voor vastgelegde items te starten. Op het
scherm wordt 'CHE' weergegeven.
Wordt gebruikt om een controleproces te starten. Bij een controleproces wordt
de invoer van de gebruiker vergeleken met de eerder vastgelegde
bewerkingswachtrij. Op het scherm wordt 'CHE StArt' weergegeven.
De instelling van de schakelaars moet overeenkomen met de invoer bij de eerste en
tweede bewerking. Als de schakelaars niet overeenkomen, wordt het onderstaande
bericht afgedrukt.
* ••001•• – Instelling voor decimaalteken is niet gelijk
* ••002•• – Instelling voor afronden is niet gelijk
Deze rekenmachine heeft een bewerkingswachtrij van 100 stappen; dit is handig voor het
controleproces. Als de bewerkingswachtrij vol is, kan de functie Dubbel controleren niet
worden gebruikt en wordt het bericht 'E CHE St Full' op het scherm weergegeven.
Druk bij de eerste invoer op de toets om de berekening voor de controle te
beëindigen. ' ,,.,.,,' wordt afgedrukt.
Druk bij de twaeede invoer op de toets om het controleproces af te breken. '••000••'
wordt afgedrukt.

OVERLOOPFUNCTIE

In de volgende gevallen, wanneer 'E' wordt weergegeven, wordt een stippellijn afgedrukt en
het toetsenbord elektronisch vergrendeld. De rekenmachine werkt niet meer. Druk op
om de overloop te wissen. De overloop treedt op als:
1) het resultaat of de inhoud van het geheugen langer is dan 12 cijfers links van het
decimaalteken;
2) u deelt door '0';
3) de snelheid waarmee bewerkingen worden ingevoerd hoger is dan de snelheid waarmee
de berekening wordt verwerkt. (Overloop bufferregister)

SPECIFICATIES

Bedrijfstemperatuur: 0 tot 40 ºC
Automatisch uitschakelen: na circa 7 minuten
Afmetingen: 196 mm (L) x 99 mm (B) x 40 mm (H)
Gewicht: 304 g met batterijen / 234 g zonder batterijen
(Deze informatie kan zonder voorafgaande kennisgeving worden gewijzigd)

NEDERLANDS

BEREGNINGER MED DECIMALER

Decimalvælgertast – bruges til at angive placeringen af decimalpunktet
(F, 0, 2, 3, 4, A) for beregnede resultater.
A (Tilføj-tilstand) – funktionerne for addition og subtraktion udføres
automatisk med to decimaler. Dette er praktisk til valutaberegninger.
F (Flydende decimalpunkt) – alle faktiske tal op til 12 cifre udskrives eller
vises i displayeet. (der vises ikke noget "F"-ikon)
Afrundingstast – bruges til at runde op [ ] , afrunde [5/4] eller runde ned
[ ] til de forudvalgte decimalcifre for resultatet.

VIGTIGE FUNKTIONER

Tasten On/Clear/Off – bruges til at tænde regnemaskinen.
Når du laver en beregning, kan du nulstille den sidst indtastede værdi ved at
trykke én gang. Tryk igen for at nulstille alle indtastede værdier med
undtagelse af hukommelsen. Denne tast bruges også til at nulstille
overløbsfejl. Tryk på tasten, og hold den inde i to sekunder for at slukke
regnemaskinen.
Tasten Print On/Off – bruges til at tænde og slukke printeren.
Når mærket for "PRINT" vises på displayet, vises indtastninger og resultater
på displayet og udskrives.
Når mærket for "PRINT" ikke vises på displayet, vises indtastninger og
resultater på displayet, men udskrives ikke.
Tasten Business/Tax – bruges til at skifte mellem handelsberegning og
momsberegning.
Tasten Paper feed – bruges til at fremføre papiret.
Tasten Rate Set – bruges til at angive momsats eller valutakurs.
Tasten Memory/Currency – bruges til at skifte mellem hukommelse og
valutaberegning.
Tasten Non-Add – bruges til at udskrive oplysninger, der ikke berører
beregningen, f.eks. datoer og serienumre. Tallene udskrives i venstre side af
papiret.
Tasten Equal – bruges til at addere, subtrahere, multiplicere og dividere.

BEREGNING AF TID

Bruges til at beregne tid eller varighed af aktiviteter, f.eks. løntimer og
omkostningsberegninger.
Bruges til at skifte mellem AM ("AM" vises, og " • " udskrives), PM
("PM" vises, og " •• " udskrives) eller 24-timers format (intet ikon vises
eller udskrives) i tidsberegningstilstand.
** Inputværdi i minutter: 0 til 59. Værdier, der er højere end 59, justeres automatisk ved at
tilføje time/timer.
** Beregningsområde: –99 timer og 59 minutter til 99 timer og 59 minutter. Hvis
input-/outputværdien er uden for det tilladte område, sker der et overløb af
tidsberegningen.

BEREGNING AF VALUTAKONVERTERING

Tryk på for at konvertere det viste valutatal fra til eller .
Tryk på eller for at konvertere det viste tal fra eller
til .
Ved kurser på 1 eller højere kan du indtaste op til 6 cifre. Ved kurser på mindre end 1
kan du indtaste op til 8 cifre (f.eks. 0,1234567), inklusive 0 for heltal og indledende nuller
(selvom der kun kan angives 7 betydende cifre talt fra venstre og med start fra det første
ciffer, der ikke er nul).

FUNKTION TIL MOMSBEREGNING

Tasten Add Tax – bruges til at tilføjes momsbeløbet til det viste tal.
Tasten Deduct Tax– bruges til at fratrække momsbeløbet fra det viste tal.
Bemærk: Den indtastede momssats gemmes, også selvom regnemaskinen slukkes. Den
indtastede sats slettes dog, hvis stikket tages ud af stikkontakten. Hvis dette
sker, skal du indtaste satsen igen.

BEREGNING AF OMKOSTNINGS-/SALGSMARGIN

Bruges til beregning af omkostning, salgspris, avance og beløb for marginværdi.
Indtast værdien af to vilkårlige elementer for at få saldoværdien. (Indtast f.eks.
værdien af omkostningen og salgsprisen for at få overskudsmargin i procent).

FUNKTION TIL DOBBELTKONTROL

Bruges til at starte proces for kontrol af registreringer. "CHE" vises på displayet.
Bruges til at starte en kontrolproces. Kontrolprocessen sammenligner brugerens
input med den tidligere registrerede betjeningskø. "CHE StArt" vises på
displayet.
Indstillingen af knapperne skal stemme overens med det første og andet input. Hvis
knapperne ikke stemmer overens, udskrives følgende meddelelse.
* ••001•• – Decimal point setting is different (Indstilling af decimalpunkt er ikke ens)
* ••002•• – Rounding setting is different (Indstilling af afrunding er ikke ens)
Denne regnemaskine har en betjeningskø på 100 trin, hvilket er nyttigt i forbindelse med
kontrolprocessen. Hvis det ligger uden for betjeningskøen, kan det ikke medtages i
dobbeltkontrolfunktionen, og meddelelsen "E CHE St FULL" vises på displayet.
Ved det første input skal du trykke på tasten for at afslutte kontrol af beregningen.
",,.,.,," udskrives.
Ved det andet input skal du trykke på tasten for at afbryde kontrolprocessen.
"••000••" udskrives.

OVERLØBSFUNKTION

I følgende tilfælde vil der, når der vises et "E" i displayet, udskrives en punkteret linje,
tastaturet låses elektronisk, og det er ikke muligt at udføre yderligere handlinger. Tryk på
for at fjerne overløbet. Overløb forekommer i følgende tilfælde:
1) Resultatet eller indholdet af hukommelsen overstiger 12 cifre til venstre for
decimaltegnet.
2) Der divideres med "0".
3) Hastigheden for sekventielle handlinger overstiger hastigheden for beregningen.
(Overløb i bufferregister)

SPECIFIKATIONER

Driftstemperatur: 0 ºC to 40 ºC
Automatisk slukning: ca. syv minutter
Mål: 196 mm (L) x 99 mm (B) x 40 mm (H)
Vægt: 304 g med batterier/ 234 g uden batterier
(Kan ændres uden varsel)

DANSK

DESIMAALIEN KÄYTTÖ LASKUTOIMITUKSISSA

Decimal Point Selector -näppäin – käytetään desimaalipaikan
määrittämiseen (F, 0, 2, 3, 4, A) laskutoimituksen tuloksissa.
A (Add-Mode) – yhteenlasku- ja vähennystoiminnot tehdään automaattisesti
kahdella desimaalilla. Tästä on hyötyä valuuttalaskutoimituksissa.
F (Floating Decimal point) – kaikki vaikuttavat numerot 12 merkkiin saakka
tulostetaan tai näytetään. (näytössä ei ole F-kuvaketta)
Rounding-näppäin – käytetään pyöristämiseen ylöspäin [ ],
pyöristämiseen [5/4] tai pyöristämiseen alaspäin [ ] tuloksessa valmiiksi
valittuihin desimaaleihin.

TÄRKEITÄ MUISTETTAVIA TOIMINTOJA

On/Clear/Off-näppäin – Käytetään laskimen kytkemiseen päälle.
Tyhjennä viimeksi annettu arvo painamalla kerran laskutoimitusta tehdessäsi.
Tyhjennä kaikki annetut arvot muistia lukuun ottamatta painamalla uudelleen.
Tällä näppäimellä tyhjennetään myös ylivuotovirhe. Kytke laskin pois päältä
painamalla näppäintä 2 sekuntia.
Print On/Off -näppäin – Käytetään tulostimen kytkemiseen päälle ja pois
päältä.
Kun PRINT-merkintä näkyy näytössä, syötteet ja tulokset näkyvät näytössä ja
ne tulostuvat.
Kun PRINT-merkintää ei näy näytössä, syötteet ja tulokset näkyvät näytössä,
mutta ne eivät tulostu.
Business / Tax Function -näppäin – käytetään vaihtamaan Business- tai
Tax-laskennan välillä.
Paper Feed -näppäin – käytetään paperin liikuttamiseen.
Rate Set -näppäin – käytetään veroprosentin tai valuuttakurssin
asettamiseen.
Memory / Currency Function -näppäin – käytetään vaihtamaan Memory- tai
Currency Conversion -laskennan välillä.
Non-Add-näppäin – Käytetään tulostamaan tietoja, jotka eivät vaikuta
laskutoimitukseen, kuten päivämäärät ja sarjanumerot. Arvot tulostuvat
paperin vasempaan reunaan.
Equal-näppäin – käytetään yhteenlaskun, vähennyslaskun, kertolaskun tai
jakolaskun tulosten saamiseen.

KELLONAIKALASKU

Käytetään laskemaan ajan määrä tai toimintojen kesto, kuten
palkanmaksun tunnit ja kustannusarvio.
käytetään vaihtamaan AM-asennon (AM näkyy näytössä ja • tulostuu),
PM-asennon (PM näkyy näytössä ja •• tulostuu) tai 24 tunnin (kuvaketta ei
näy eikä se tulostu) välillä kellonajan laskutoimitustilassa.
** Minuuttien syöttöarvo: 0–59. Arvot, jotka ovat suurempia kuin 59, muutetaan
automaattisesti lisäämällä tunteja.
** Laskualue: –99 tuntia 59 minuuttia … 99 tuntia 59 minuuttia. Jos annettu tai tuloksena
saatava arvo ei ole sallitulla alueella, kellonajan laskutoimitus saa aikaan
ylivuotovirheen.

VALUUTTAMUUNNOSLASKENTA

Paina -näppäintä, jos haluat muuntaa näkyvän valuutta-arvon
-arvosta - tai -arvoksi.
Paina - tai -näppäintä, kun haluat muuttaa näkyvän luvun - tai
-arvosta -arvoksi.
Yhdelle (1) ja suuremmille arvoille voi antaa enintään kuusi (6) numeroa. Yhtä (1)
pienemmille arvoille voi antaa enintään kahdeksan (8) numeroa (esim. 0,1234567)
sisältäen nollan kokonaisluvulle ja alussa olevat nollat (vaikka vain seitsemän (7)
merkityksellistä numeroa voidaan määrittää laskettuna vasemmalta ja aloittaen
ensimmäisestä luvusta, joka ei ole nolla).

VEROLASKENTATOIMINTO

Add Tax -näppäin – verosumman lisääminen näkyvään arvoon.
Deduct Tax -näppäin – verosumman vähentäminen näkyvästä arvosta.
Huom. Annettu veroprosentti pysyy tallennettuna, vaikka laskin kytketään pois päältä.
Annettu veroprosentti poistetaan, kun pistoke irrotetaan. Anna tässä tilanteessa prosentti
uudelleen.

KUSTANNUS-MYYNTI-KATE-LASKENTA

Käytetään kustannuksen, myyntihinnan, kateprosentin ja katesumman
laskentaan. Saat tuloksen tahansa kahden kohteen arvon. (esim. anna
kustannus ja myyntihinta, jotta saat kateprosentin %.)

VARMISTUSTOIMINTO

Käytetään tietueen tarkistusprosessin (Check record) käynnistämiseen. CHE
tulee näyttöön.
Käytetään tarkistusprosessin (Check) käynnistämiseen. Tarkistusprosessissa
käyttäjän antamia arvoja verrataan aiemmin kirjattuun käyttöjonoon.
CHE StArt tulee näyttöön.
Kytkinten asetuksen on vastattava ensimmäistä ja toista toimintosyötettä. Jos kytkimet
eivät vastaa toisiaan, alla oleva viesti tulostuu.
* ••001•• – desimaaliasetuksessa on eroa
* ••002•• – pyöristysasetuksessa on eroa
Laskimessa on 100 vaiheen toimintojono, josta on hyötyä tarkistusprosessissa. Jos
laskin on toimintojonon ulkopuolella, se ei salli siirtymistä Double Check -toimintoon.
Viesti E CHE St FULL tulee näyttöön.
Paina ensimmäisessä syötteessä -näppäintä laskutoimituksen lopettamiseksi
tarkistusta varten. ,,.,.,, tulostuu.
Paina toisessa syötteessä -näppäintä ja keskeytä tarkistusprosessi. ••000••
tulostuu.

YLIVUOTOTOIMINTO

Seuraavissa tapauksissa, kun E tulee näkyviin, pisteviiva tulostuu, näppäimistö lukkiutuu
sähköisesti ja jatkokäyttö on mahdotonta. Tyhjennä ylivuoto painamalla -näppäintä.
Ylivuotoa ilmenee, kun
1) tulos tai muistin sisältö ylittää 12 merkkiä desimaalipilkun vasemmalla puolella
2) yritetään jakaa nollalla
3) peräkkäinen käyttönopeus on suurempi kuin laskimen käsittelynopeus. (puskurimuistin
ylivuoto)

TEKNISET TIEDOT

Käyttölämpötila: 0–40 ºC
Automaattinen virrankatkaisu: n. 7 minuuttia
Mitat: 196 mm (pituus) x 99 mm (leveys) x 40 mm (korkeus)
Paino: 304 g paristojen kanssa / 234 g ilman paristoja
(Voi muuttua ilman erillistä ilmoitusta)

SUOMI

RÄKNA MED DECIMALER

Knappen Decimal Point Selector – Används för att utse decimaltecknets
läge (F, 0, 2, 3, 4, A) i framräknade resultat.
A (Add-Mode) – Funktionerna för addition och subtraktion utförs automatiskt
med två decimaler. Det är praktiskt vid valutaberäkningar.
F (Flytande decimaltecken) – Alla effektiva nummer på upp till 12 siffror
skrivs ut eller visas. (ikonen "F" visas inte)
Knappen Rounding – Används för avrundning uppåt [ ], avrundning [5/4]
och avrundning nedåt [ ] till det förvalda antalet decimaler i resultatet.

FUNKTIONER SOM ÄR VIKTIGA ATT KOMMA IHÅG

Knappen On/Clear/Off – Används för att slå på kalkylatorn.
När du räknar trycker du på knappen en gång för att ta bort det senast
inmatade värdet. Tryck på knappen igen om du vill radera alla inmatade
värden, förutom minnet. Med den här knappen kan du även radera spillfel.
Tryck ned knappen i två sekunder när du vill stänga av kalkylatorn.
Knappen Print On/Off – Används för att slå på och stänga av skrivaren.
När "PRINT"-märket visas på skärmen visas inmatningar och resultat på
skärmen och skrivs ut.
När "PRINT"-märket inte visas på skärmen visas inmatningar och resultat på
skärmen, men skrivs inte ut.
Knappen Business/Tax Function – Används för att växla mellan
verksamhets- och skatteberäkningar.
Knappen Paper Feed – Används för att mata fram papperet.
Knappen Rate Set – Används för att ställa in skattesats eller
valutaomvandlingskurs.
Knappen Memory/Currency Function – Används för att växla mellan
minnes- eller valutaomvandlingsberäkning.
Knappen Non-Add – Används för att skriva ut information som inte påverkar
beräkningen, till exempel datum och serienummer. Siffror skrivs ut på vänster
sida av papperet.
Knappen Equal – Används för att få fram resultat av addition, subtraktion,
multiplikation och division.

TIDSBERÄKNING

Används för att beräkna tiden eller hur lång tid aktiviteter tar, till exempel
lönetimmar och kostnadsuppskattning.
Används för att växla mellan förmiddag ("AM" visas och " • " skrivs ut),
eftermiddag ("PM" visas och " •• " skrivs ut) och 24 timmar (ingen ikon
visas och skrivs ut) i beräkningsläget för tid.
** Inmatningsvärde för minuter: 0 till 59. Värden som överstiger 59 justeras automatiskt
genom att antalet timmar läggs till.
** Beräkningsintervall: –99 timmar 59 minuter till 99 timmar 59 minuter. Om
indata-/utdatavärdet ligger utanför det tillåtna intervallet orsakar tidsberäkningen ett spill.

BERÄKNING AV VALUTAOMVANDLING

Tryck på för att omvandla den valutasymbol som visas från till
eller .
Tryck på eller för att omvandla den symbol som visas från
eller till .
För kurser på 1 eller högre kan du mata in upp till 6 siffror. För kurser på mindre än 1
kan du mata in upp till 8 siffror (t.ex. 0,1234567), inklusive 0 för heltalet och inledande
nollor (men endast 7 siffror av betydelse, räknat från vänster från den första siffran
som inte är en nolla, kan anges).

FUNKTION FÖR SKATTEBERÄKNING

Knappen Add Tax – Används för att lägga till ett skattebelopp i summan
som visas.
Knappen Deduct Tax – Används för att dra av skattebeloppet från
summan som visas.
Obs! Den angivna skattesatsen sparas även när kalkylatorn är avslagen. Men den angivna
satsen raderas när stickkontakten dras ut. I så fall anger du satsen på nytt.

BERÄKNING AV MARGINALEN FÖR KOSTNAD/FÖRSÄLJNING

Används för att beräkna kostnad, försäljningspris, vinstmarginal och
marginalvärdesbelopp. Mata in värdet för 2 olika saker för att få ett balansvärde.
(ange t.ex. värdet för kostnad och försäljningspris för att få fram vinstmarginal i
procent.)

FUNKTIONEN FÖR DUBBELKONTROLL

Används för att starta processen för att kontrollera poster. "CHE" visas på
skärmen.
Används för att starta en kontrollprocess. Under kontrollen jämförs
användarens indata med den tidigare registrerade åtgärdskön. "CHE StArt"
visas på skärmen.
Inställningen i omkopplarna måste stämma överens med den första och andra
åtgärdsinmatningen. Om omkopplarna inte stämmer skrivs meddelandet nedan ut.
* ••001•• – Decimal point setting is different
* ••002•• – Rounding setting is different
Den här kalkylatorn har en åtgärdskö på 100 steg, vilket är praktiskt vid kontrollproces
sen. Utanför åtgärdskön är det inte tillåtet att använda dubbelkontrollsfunktionen och
meddelandet "E CHE St FULL" visas på skärmen.
Vid den första inmatningen trycker du på knappen för att avsluta beräkningen för
kontroll. ",,.,.,," skrivs ut.
Vid den andra inmatningen trycker du på knappen för att avbryta kontroll
processen. "••000••" skrivs ut.

SPILLFUNKTIONEN

I följande fall sker följande när "E" visas: en prickad linje skrivs ut, tangentbordet låses
elektroniskt och inga fler åtgärder kan vidtas. Tryck på för att radera spillet. Spillet
sker när:
1) resultatet eller minnesinnehållet överskrider 12 siffror till vänster om decimaltecknet.
2) du delar med "0".
3) hastigheten på sekventiella åtgärder är snabbare än hastigheten på
beräkningsbehandling. (Buffertregisterspill)

TEKNISKA DATA

Drifttemperatur: 0 ºC till 40 ºC
Automatisk avstängning: cirka 7 minuter
Mått: 196 mm (L) x 99 mm (B) x 40 mm (H)
Vikt: 304 g med batterier/234 g utan batterier
(kan komma att ändras utan föregående meddelande)

SVENSKA

E-IM-3031
© CANON ELECTRONIC BUSINESS MACHINES CO., LTD 2017
/
$
C1
C2
$
C1
C2
$
C1
C2
C1
C2
$
CHECK
/
/
$
C1
C2
$
C1
C2
$
C1
C2
C1
C2
$
CHECK
/
/
$
C1
C2
$
C1
C2
$
C1
C2
C1
C2
$
CHECK
/
/
$
C1
C2
$
C1
C2
$
C1
C2
C1
C2
$
CHECK
/
/
$
C1
C2
$
C1
C2
$
C1
C2
C1
C2
$
CHECK
/
/
$
C1
C2
$
C1
C2
$
C1
C2
C1
C2
$
CHECK
/

Decimal point selection / Dezimalstellen-schalter /

Sélecteur de virgule décimale / Conmutador Selector

de Punto Decimal / Selettore del punto decimale /

Selectietoets voor aantal decimalen /

Valgtast for decimalpunkt / Desimaalipisteen valintanäppäin /

Decimalpunktsväljaren

View the manual for the Canon P1-DTSC II here, for free. This manual comes under the category calculators and has been rated by 2 people with an average of a 8.5. This manual is available in the following languages: English. Do you have a question about the Canon P1-DTSC II or do you need help? Ask your question here

Need help?

Do you have a question about the Canon and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

General
BrandCanon
ModelP1-DTSC II | P1-DTSC II
Productcalculator
EAN4549292105988
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Canon P1-DTSC II below.

What is an Overflow error?

An Overflow error usually occurs when the sum result is longer than the calculator can show.

A battery in my calculator has started to corrode. Is the device still safe to use?

The product can still be used safely after proper cleaning. Remove the battery with gloves and clean the battery compartment with a toothbrush and vinegar. After drying, new batteries can be inserted into the device.

What does AC stand for on my calculator?

AC stands for 'all clear'. You clear the entire memory of the calculator with this button.

How do I troubleshoot if the calculation range of the Canon P1-DTSC II calculator is not working properly?

To troubleshoot if the calculation range of the Canon P1-DTSC II calculator is not working properly, you can follow these steps: 1. Check the input: Ensure that you are entering the correct values within the allowable range. The calculation range of the calculator is -99 hours 59 minutes to 99 hours 59 minutes. If the input value is outside this range, the time calculation will overflow. 2. Verify the output: Double-check the displayed result to see if it falls within the expected range. If the output value is not within the allowable range, it may indicate an issue with the calculator. 3. Reset the calculator: If you encounter any errors or unexpected behavior, try resetting the calculator. Press the On/Clear/Off key to clear all entered values and reset the calculator to its default state. 4. Replace batteries: In some cases, a low battery level can affect the performance of the calculator. If the calculation range issue persists, try replacing the batteries with fresh ones. 5. Contact customer support: If the troubleshooting steps above do not resolve the problem, it is recommended to reach out to Canon customer support for further assistance. They can provide specific guidance based on the issue you are experiencing. Remember to refer to the user manual for detailed instructions on using the calculator and troubleshooting common issues.

What should I do if the currency conversion function of the Canon P1-DTSC II calculator is not giving accurate results?

If the currency conversion function of the Canon P1-DTSC II calculator is not giving accurate results, you can try the following steps to troubleshoot the issue: 1. Verify the currency rates: Ensure that you have entered the correct currency exchange rates. Check if the rates are up to date and accurately inputted into the calculator. 2. Check decimal point settings: Make sure that the decimal point setting is appropriate for the currency conversion calculation. The calculator offers different decimal point options (F, 0, 2, 3, 4, A). Select the correct setting based on your calculation requirements. 3. Confirm input values: Double-check the values you are entering for currency conversion. Ensure that you are inputting the correct amounts for both the source and target currencies. 4. Reset the calculator: If you are still experiencing inaccuracies, try resetting the calculator by pressing the On/Clear/Off key. This will clear any previous calculations and restore the calculator to its default state. 5. Contact customer support: If the issue persists, it is recommended to reach out to Canon customer support for further assistance. They can provide specific guidance and troubleshooting steps based on the currency conversion function of the Canon P1-DTSC II calculator. Remember to refer to the user manual for detailed instructions on using the currency conversion function and troubleshooting common issues.

How can I troubleshoot if the tax function of the Canon P1-DTSC II calculator is not adding or deducting the tax amount correctly?

To troubleshoot if the tax function of the Canon P1-DTSC II calculator is not adding or deducting the tax amount correctly, you can follow these steps: 1. Verify the tax rate: Check if the entered tax rate is accurate. Ensure that you have inputted the correct percentage or decimal value for the tax rate. 2. Confirm the tax calculation method: Ensure that you are using the correct tax calculation method based on your local tax regulations. Different regions may have different tax calculation methods, such as inclusive or exclusive tax. 3. Check the tax keys: Make sure you are using the correct tax keys on the calculator. The "Add Tax" key is used to add the tax amount to the displayed figure, while the "Deduct Tax" key is used to subtract the tax amount. 4. Reset the calculator: If you are still experiencing issues, try resetting the calculator by pressing the On/Clear/Off key. This will clear any previous calculations and restore the calculator to its default state. 5. Contact customer support: If the problem persists, it is recommended to contact Canon customer support for further assistance. They can provide specific guidance and troubleshooting steps based on the tax function of the Canon P1-DTSC II calculator. Remember to refer to the user manual for detailed instructions on using the tax function and troubleshooting common issues.

What should I do if the business function of the Canon P1-DTSC II calculator is not calculating the cost, selling price, or profit margin accurately?

If the business function of the Canon P1-DTSC II calculator is not calculating the cost, selling price, or profit margin accurately, you can try the following steps to troubleshoot the issue: 1. Verify input values: Double-check the values you are entering for cost, selling price, and profit margin calculations. Ensure that you have inputted the correct amounts for each item. 2. Check calculation method: Confirm that you are using the correct calculation method for the business function. The calculator may have different options for calculating the cost, selling price, and profit margin. Select the appropriate method based on your calculation requirements. 3. Review decimal point settings: Make sure that the decimal point setting is appropriate for the calculations. The calculator offers different decimal point options (F, 0, 2, 3, 4, A). Select the correct setting to ensure accurate calculations. 4. Reset the calculator: If you are still experiencing inaccuracies, try resetting the calculator by pressing the On/Clear/Off key. This will clear any previous calculations and restore the calculator to its default state. 5. Contact customer support: If the issue persists, it is recommended to reach out to Canon customer support for further assistance. They can provide specific guidance and troubleshooting steps based on the business function of the Canon P1-DTSC II calculator. Remember to refer to the user manual for detailed instructions on using the business function and troubleshooting common issues.

How do I troubleshoot if the battery replacement process of the Canon P1-DTSC II calculator is not working as described in the manual?

To troubleshoot if the battery replacement process of the Canon P1-DTSC II calculator is not working as described in the manual, you can follow these steps: 1. Lift up the paper arm: Raise the paper arm of the calculator to access the battery compartment. 2. Place the new battery: Insert the new battery into the designated slot in the battery compartment. Ensure that the positive (+) and negative (-) ends of the battery align correctly with the markings inside the compartment. 3. Verify battery type: Make sure you are using the correct type of battery recommended for the Canon P1-DTSC II calculator. Refer to the manual or the markings inside the battery compartment for the specific battery type. 4. Check battery polarity: Double-check the polarity of the battery. The positive (+) end should be facing in the correct direction as indicated inside the battery compartment. 5. Close the battery compartment: Once the new battery is properly inserted, close the battery compartment securely. 6. Test the calculator: Turn on the calculator and check if it is functioning correctly. If the battery replacement process was successful, the calculator should power on and operate as expected. If the issue persists after following these steps, it is recommended to contact Canon customer support for further assistance. Please note that the battery replacement process may vary slightly depending on the specific model of the Canon P1-DTSC II calculator.

How do I troubleshoot if the calculation range of the Canon P1-DTSC II calculator is not displaying the correct results?

To troubleshoot if the calculation range of the Canon P1-DTSC II calculator is not displaying the correct results, you can follow these steps: 1. Check the input values: Ensure that you are entering the correct numbers or calculations into the calculator. Double-check for any errors or typos in the input. 2. Verify the calculation range: The Canon P1-DTSC II calculator has a calculation range of -99 hours 59 minutes to 99 hours 59 minutes. Make sure that the values you are trying to calculate fall within this range. 3. Reset the calculator: If you are experiencing issues with the calculation range, try resetting the calculator. Press the "On/Clear/Off" key to clear any previous calculations and start fresh. 4. Check for overflow: If the input or output value exceeds the allowable range, the calculator may display an overflow error. If this happens, try reducing the values or breaking down the calculation into smaller steps. 5. Consult the user manual: If the issue persists, refer to the user manual for further troubleshooting steps or contact Canon customer support for assistance. By following these steps, you can troubleshoot and resolve any issues related to the calculation range of the Canon P1-DTSC II calculator.

What should I do if the currency conversion function of the Canon P1-DTSC II calculator is not converting the figures accurately?

If the currency conversion function of the Canon P1-DTSC II calculator is not converting the figures accurately, you can try the following steps to troubleshoot the issue: 1. Verify the input values: Double-check the currency figures you are entering into the calculator. Ensure that you are inputting the correct values for both the source currency and the target currency. 2. Check the decimal point setting: Make sure that the decimal point setting is appropriate for the currency conversion. The Canon P1-DTSC II calculator allows you to designate the decimal point position for calculated results. Ensure that the decimal point setting is aligned with the desired precision for the conversion. 3. Confirm the exchange rate: Ensure that you have entered the correct exchange rate for the currency conversion. Use the rate set key to input the accurate exchange rate between the source and target currencies. 4. Reset the calculator: If the issue persists, try resetting the calculator by pressing the "On/Clear/Off" key. This will clear any previous calculations and settings, allowing you to start fresh. 5. Consult the user manual: If the problem continues, refer to the user manual for further troubleshooting steps or contact Canon customer support for assistance. By following these steps, you can troubleshoot and resolve any inaccuracies in the currency conversion function of the Canon P1-DTSC II calculator.

How can I troubleshoot if the tax function of the Canon P1-DTSC II calculator is not adding or deducting tax amounts correctly?

To troubleshoot if the tax function of the Canon P1-DTSC II calculator is not adding or deducting tax amounts correctly, you can follow these steps: 1. Verify the tax rate: Check that you have entered the correct tax rate into the calculator. Use the rate set key to input the accurate tax rate. 2. Confirm the tax calculation method: Ensure that you are using the correct tax calculation method for your region or jurisdiction. The Canon P1-DTSC II calculator offers different tax calculation options, such as adding or deducting tax amounts. 3. Check the decimal point setting: Make sure that the decimal point setting is appropriate for the tax calculation. The Canon P1-DTSC II calculator allows you to designate the decimal point position for calculated results. Ensure that the decimal point setting is aligned with the desired precision for the tax calculation. 4. Reset the calculator: If the issue persists, try resetting the calculator by pressing the "On/Clear/Off" key. This will clear any previous calculations and settings, allowing you to start fresh. 5. Consult the user manual: If the problem continues, refer to the user manual for further troubleshooting steps or contact Canon customer support for assistance. By following these steps, you can troubleshoot and resolve any issues related to the tax function of the Canon P1-DTSC II calculator.

What steps should I take if the business function of the Canon P1-DTSC II calculator is not calculating costs, selling prices, or profit margins accurately?

To troubleshoot if the business function of the Canon P1-DTSC II calculator is not calculating costs, selling prices, or profit margins accurately, you can follow these steps: 1. Verify the input values: Double-check the values you are entering into the calculator for cost, selling price, and profit margin. Ensure that you are inputting the correct figures for each item. 2. Check the decimal point setting: Make sure that the decimal point setting is appropriate for the calculation. The Canon P1-DTSC II calculator allows you to designate the decimal point position for calculated results. Ensure that the decimal point setting is aligned with the desired precision for the business calculations. 3. Confirm the calculation method: Ensure that you are using the correct calculation method for the specific business calculation you are performing. The Canon P1-DTSC II calculator offers different calculation options for cost, selling price, and profit margin. 4. Reset the calculator: If the issue persists, try resetting the calculator by pressing the "On/Clear/Off" key. This will clear any previous calculations and settings, allowing you to start fresh. 5. Consult the user manual: If the problem continues, refer to the user manual for further troubleshooting steps or contact Canon customer support for assistance. By following these steps, you can troubleshoot and resolve any inaccuracies in the business function of the Canon P1-DTSC II calculator.

What should I do if I encounter difficulties while installing printing paper in the Canon P1-DTSC II calculator's printer mechanism?

To install printing paper in the Canon P1-DTSC II calculator's printer mechanism, follow these steps: 1. Lift up the paper arm to access the printer mechanism. 2. Cut the edge of the paper to ensure a clean and straight edge. 3. Place the new paper roll on the paper arm, aligning the edge of the paper as shown in the manual. 4. Insert the paper into the slit at the top of the calculator, following the indicated direction. 5. Turn on the calculator and press the paper feed key to advance the paper and ensure it is properly aligned. If you encounter difficulties during the installation process, consider the following troubleshooting steps: 1. Check that you are using the correct paper size and type specified for the Canon P1-DTSC II calculator. 2. Ensure that the paper roll is inserted securely onto the paper arm. 3. Verify that the paper is inserted into the slit at the top of the calculator correctly, following the indicated direction. 4. If the paper does not feed properly, check for any obstructions or jams in the printer mechanism. 5. If the issue persists, consult the user manual for further troubleshooting steps or contact Canon customer support for assistance. By following these steps and troubleshooting tips, you can successfully install printing paper in the Canon P1-DTSC II calculator's printer mechanism.

Is the manual of the Canon P1-DTSC II available in English?

Yes, the manual of the Canon P1-DTSC II is available in English .

Is your question not listed? Ask your question here

No results