Canon imageFORMULA CR-190i II manual

Canon imageFORMULA CR-190i II
7.9 · 1
PDF manual
 · 63 pages
English
manualCanon imageFORMULA CR-190i II
41
If there is a problem with the scanned image (the image is not sharp or
stripes appear), one of the following conditions may be a probable
cause. Check the following conditions, and take the appropriate action.

The scanning glass or rollers are dirty.

If the scanning glass or rollers are dirty, the dirt will appear on the
scanned image.
Clean the scanning glass and rollers. For details, see “Cleaning
the Scanning Glass and Rollers,” on p. 44.

The scan conditions are inappropriate.

If the scan conditions are inappropriate, the scanned image will not
be sharp or will appear as dark.
Check the brightness and other scanner settings.
If the scanned image is blurry or the document has not been
scanned at all, the brightness may be set too high.
If the scanned image appears dark, the brightness may be set too
low.
Also, check the settings on the driver and the software application.

The driver or application does not run correctly.

If the document cannot be scanned correctly even if the scan
conditions are adjusted, the driver or the application may not be
functioning correctly.
Reinstall the driver or application.
For details on how to install the driver, see “Installing the Software,”
on p. 18.
For details on how to install the application, see the applications
instruction manual.

The CR-135i II/CR-190i II is not recognized by your

computer.

Try the following:
Restart your computer.
If your computer has multiple USB ports, try using a different USB
port.
Disconnect the USB cable, make sure the computer and scanner
are turned ON, and then reconnect the cable.

Memory becomes insufficient and scanning stops.

If you configure scanning conditions that use a large amount of the
computer’s memory, scanning may stop because of insufficient
memory. Although this depends on the computer’s memory size, the
possibility of insufficient memory increases if any of the following
scanning conditions overlap.
The page size is set to [Scanner’s Maximum].
A high resolution (300dpi etc.) is specified for [Dots per inch].
If an error message appears due to insufficient memory while scanning
is in progress, exit the application, change the scanning conditions
(e.g. reduce the resolution or page size) and then try scanning again.

The CR-135i II/CR-190i II turns OFF automatically.

Check whether the Auto Power OFF function of the CR-135i II/CR-190i II
is enabled. If it is enabled, disable it.

Other Causes

Even if the computer may be recognizing the scanner correctly, and
the driver and the application is installed correctly, scanning may
not be performed correctly. If this happens, the interface card is not
compatible. Use the recommended interface card.
If the above remedies do not rectify the problem, contact your local
authorized Canon dealer or service representative to have the scanner
serviced.

When the Scanned Image Is Not

Normal

View the manual for the Canon imageFORMULA CR-190i II here, for free. This manual comes under the category scanners and has been rated by 1 people with an average of a 7.9. This manual is available in the following languages: English. Do you have a question about the Canon imageFORMULA CR-190i II or do you need help? Ask your question here

Need help?

Do you have a question about the Canon and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

General
BrandCanon
ModelimageFORMULA CR-190i II
Productscanner
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Canon imageFORMULA CR-190i II below.

Is the manual of the Canon imageFORMULA CR-190i II available in English?

Yes, the manual of the Canon imageFORMULA CR-190i II is available in English .

Is your question not listed? Ask your question here

No results