Britax KING II manual

Britax KING II
9.4 · 1
PDF manual
 · 2 pages
English
manualBritax KING II
01
10
18
19
04
Adjustment leverHeadrest adjuster (KING II ATS/LS)Lower belt guide Release buttons Seat shellUpper belt guideSeat base
01
02
03
04
05
06
07
Indicator light (KING II LS)Shoulder pads HeadrestHeadrest adjuster (KING II)Adjusting button
08
09
10
Shoulder straps
11
Harness buckle
12
13
14
Adjustment strapIndicator light (KING II ATS)
15
16
Adjustment handle
17
User guide compartment
18
Harness retainer
19
02
03
05
06
07
08
09
11
12
13
14
15
17
16

KING II / ATS / LS

User instructions
www.britax.eu
2000021398 11/14
GB

9 kg - 18 kg

9 M
~
4 Y

2. INTRODUCTION

We are delighted that our
KING II / ATS / LS
can safely accompany your child
through a new stage in its life.
In order to protect your child correctly, the
KING II / ATS / LS
must al-
ways be used and installed as described in these instructions.
If you have any further questions regarding its use, please feel free to contact us:
BRITAX RÖMER
Kindersicherheit GmbH
Blaubeurer Straße 71
D-89077 Ulm
Germany
T.: +49 (0) 731 9345-199
F.: +49 (0) 731 9345-210
E.: service.de@britax.com
www.roemer.eu
BRITAX EXCELSIOR
LIMITED
1 Churchill Way West
Andover
Hampshire SP10 3UW
United Kingdom
T.: +44 (0) 1264 333343
F.: +44 (0) 1264 334146
E.: service.uk@britax.com
www.britax.eu
These instructions use the following symbols stated below:
Symbol Keyword Explanation
DANGER! Risk of severe personal injury
WARNING! Risk of minor personal injury
CAUTION! Risk of material damage
TIP: Useful notes
Instructions that follow a set sequence are numbered.
Example:
1. Press the button...
21
22
Belt guide colours
For better differentiation, the two vehicle seat
belts are highlighted in different colours. The di-
agonal seat belt
21
in dark red and the lap belt
22
in bright red. The colour of the belt guides
on the child safety seat follows the same colour
scheme.

4. CARE AND MAINTENANCE

3. CERTIFICATION

/ USAGE

PAGE I

5. DISASSEMBLY AND DISPOSAL

1. PRODUCT OVERVIEW

DISPOSAL:Please observe the waste disposal regulations in your country..
Disposal of packaging Container for cardboard boxes
Seat cover Residual waste, thermal utilisation
Plastic parts According to the labelling in the
corresponding container
Metal parts Container for metals
Belt straps Container for polyester
Buckle and tongue Residual waste
Batteries Container for batteries
REMOVAL:UNFASTENING YOUR CHILD:
1. To unfasten your child, press the red release button of the 5-Point harness
buckle
12
.
1. Unbuckle the vehicle belt buckle
20
and loosen the harness straps.
2. Unhook the diagonal belt section
21
from the upper belt guide
01
.
3. To open the shell: push one of the grey release buttons
03
and at the
same time pull the seat shell
02
as far forward as possible.
4. Remove the diagonal
21
and the lap belt sections
22
from the light red
lower belt guides
04
.
5. Hold the seat shell
02
with one hand while pulling the grey adjustment
lever
05
forward with the other hand.
6. To close the shell: tip the seat shell
02
against the seat base
06
over both
engagement positions.
WARNING! To avoid injuries take your hand away from the grey adjust-
ment lever
05
, as soon as getting over the two engagement positions.
7. Push the seat shell
02
with both hands against the seat base
06
until it is
fully engaged.
BRITAX RÖMER Child safety seat
Testing and certication
In accordance with ECE* R 44/04
*ECE = European Standard for Child Safety Equipment
Group Body weight
KING II / ATS / LS
I 9 to 18 kg
The child safety seat has been designed, tested and certied according to the re-
quirements of the European Standard for Child Safety Equipment (ECE R 44/04).
The seal of approval E (in a circle) and the approval number are located on the
orange approval label (sticker on the child safety seat)
.
DANGER! This approval will be invalidated if you make any modications to
the child safety seat. Only the manufacturer is permitted to make
modications to the child safety seat.
DANGER! Never secure your child or the child safety seat with a 2-point belt.
If you secure your child in the child seat with only a 2-point belt,
then in the event of an accident this may cause serious injuries to
your child, possibly resulting in death.
Please observe the instructions for using children’s restraining systems in the operating
instructions of your vehicle. The seat can only be used in vehicles with 3-point retractor safety-
belts
2)
.
Please nd the information on the seats approved for child safety seats of the weight classes 9 to
18 kg in the operating instructions of your vehicle.
You can use your child safety seat as follows:
In the direction of travel yes
Against the direction of travel no
1)
with 2-point belt no
with 3-point reractor safety belt
2)
yes
on front passenger seat yes
3)
on outer rear seat yes
on centre rear seat (with 3-point
belt
2)
)
yes
4)
1) Use is permitted on a rearward-facing vehicle seat (e.g. in a van or minibus) only
if the vehicle seat is also approved for use by adults. The seat may not be in the area of effect
of an airbag.
2) The seat is only compatible with 3-point retractor type safety-belts, approved to ECE Reg
No. 16 or other equivalent standards.
3) If there is a front airbag: Slide the vehicle seat a long way back and refer to any instructions
in vehicle owners manual.
4) Cannot be used if the vehicle seat is equipped with only a 2-point belt.
9 - 18 kg
Removing the cover
Loosen the harness straps as far as possible.
1. Open the harness buckle
12
(press red button).
2. Remove the cover of the headrest
09
.
3. Open the poppers
29
on the left and right side of the
rear part of the cover.
4. Unhook the elastic seam of the cover under the edge of
the seat shell.
TIP: Start at the sides of the seat shell.
5. Pull the cover up and over the bezel of the strap adjuster.
6. Feed out the harness buckle
12
and the end of the strap
from the cover.
7. Pull the cover upwards and remove it over the headrest
09
.
The cover can now be washed. Please observe the
instructions on the washing label of the cover:
Re-tting the cover
Proceed in reverse order to put on the cover.
09
29
12
Please ensure that you only use the original BRITAX RÖMER replacement seat
covers, as the seat cover is an integral part of the child safety seat and fulls im-
portant functions to ensure the smooth operation of the system. Replacement seat
covers are available from your dealer.
• The cover can be removed and washed using the delicates programme of the
washing machine (30°C). Please observe the instructions on the washing label
of the cover.
• The plastic parts can be cleaned with a damp cloth. Do not use any caustic
cleaning agents (such as solvents).
DANGER! The child seat must not be used without the seat cover.
Care for the harness buckle
It is vital for the safety of your child that the harness buckle works correctly. Malfunctions
of the harness buckle are usually caused by accumulations of dirt or foreign bodies.
Malfunctions include the following:
• The buckle latches are ejected only slowly when the red release button is pressed.
• The buckle latches will no longer lock home (i.e. they are ejected again if you try to push
them in).
• The buckle latches engage without an audible “click“.
• The buckle latches are difcult to insert (you feel resistance).
• The buckle only opens if extreme force is applied.
Remedy:
wash out the harness buckle so that it functions properly once again.
25
12
12
27
26
Cleaning the harness buckle
1. Open the harness buckle
12
(press the red button).
2. Adjust the seat shell
02
to the upright seating
position.
3. Open the Velcro fastener on the crotch pad
25
and
remove it and retain it.
4. Grasp below the seating area the metal plate
26
which keeps the buckle
12
at the seat base and
turn it into a vertical position.
5. Slide the metal plate
26
through the slot
27
.
6. Soak the harness buckle
12
in warm water with
dishwashing liquid for at least an hour.
7. Rinse and dry the harness buckle
12
thoroughly.
8. Slide the metal plate
26
edgewise through the slot
27
in the cover and the seat base.
9. Rotate the metal plate
26
90°
DANGER! Pull the harness buckle
12
rmly to ensure
that it is securely fastened.
10. Insert the crotch pad
25
through the slot
27
and
secure the Velcro fastener.
Cleaning the occupant sensor
1.
Fold the lower part of the cover updwards.
2. Remove dirt and dust in the area of the occupant sensor
28
with a vacuum cleaner.
DANGER! The occupant sensor
28
must not come in
contact with water.
28
141106_KING_II_ATS_LS_GB.indd 1 06.11.2014 09:34:59

Manual

View the manual for the Britax KING II here, for free. This manual comes under the category Car seats and has been rated by 1 people with an average of a 9.4. This manual is available in the following languages: English. Do you have a question about the Britax KING II or do you need help? Ask your question here

Need help?

Do you have a question about the Britax KING II and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Britax KING II owners to provide you with a good answer.

Number of questions: 0

Britax KING II specifications

Below you will find the product specifications and the manual specifications of the Britax KING II.

General
Brand Britax
Model KING II | 4000984132939
Product Car seat
EAN 4000984132939
Language English
Filetype Usermanual (PDF)
Features
Car seat group 1 (9 - 18 kg; 9 months - 4 years)
Belt fastening type 3-point
Mounting type Seat belt
Adjustable headrest
Product colour Purple
Weight & dimensions
Depth 540 mm
Width 450 mm
Weight 10300 g
Height 670 mm
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Britax KING II below.

Is your question not listed? Ask your question here

No results