View the manual for the Bosch UniversalSaw 18V-100 here, for free. This manual comes under the category batteries and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Bosch UniversalSaw 18V-100 or do you need help? Ask your question here
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Bosch UniversalSaw 18V-100 below.
To determine when the battery of the Bosch UniversalSaw 18V-100 is fully charged, follow these steps: 1. Before using your power tool for the first time, fully charge the battery in the charger. The battery is supplied partially charged, so this step ensures maximum battery capacity. 2. The Bosch UniversalSaw 18V-100 uses a lithium-ion battery, which can be charged at any time without reducing its service life. Interrupting the charging process does not damage the battery. 3. When the power tool is switched on, the battery charge indicator will show the charge condition of the battery. The indicator consists of three green LEDs: - Three continuous green lights indicate a battery charge of 66-100%. - Two continuous green lights indicate a battery charge of 33-66%. - One continuous green light indicates a battery charge of 11-33%. - One slowly flashing green light indicates a battery charge of 0-10%. 4. If the three LEDs in the battery charge indicator are flashing quickly, it means that the battery temperature is outside the operating range of -20 to +50°C and/or the overload protection has been triggered. By following these steps and monitoring the battery charge indicator, you can easily determine when the battery of the Bosch UniversalSaw 18V-100 is fully charged.
To insert and remove the saw blade on the Bosch UniversalSaw 18V-100, follow these steps: 1. Ensure that the power tool is switched off and the battery is removed for safety. 2. Locate the saw blade release lever or button on the power tool. It is usually located near the blade area. 3. Press and hold the saw blade release lever or button to unlock the blade. 4. While holding the release lever or button, carefully insert the saw blade into the blade holder or clamp. Make sure the blade is properly aligned with the guide marks. 5. Release the saw blade release lever or button to secure the blade in place. Give it a gentle tug to ensure it is securely locked. 6. To remove the saw blade, repeat steps 2 and 3 to unlock the blade. 7. While holding the release lever or button, gently pull the saw blade out of the blade holder or clamp. 8. Store the saw blade in a safe place or replace it with a new one if necessary. By following these steps, you can easily insert and remove the saw blade on the Bosch UniversalSaw 18V-100 for your woodworking tasks.
If the saw blade on the Bosch UniversalSaw 18V-100 is not cutting properly, you can try the following steps to troubleshoot the issue: 1. Check the condition of the saw blade. Ensure that it is not dull, damaged, or worn out. If necessary, replace the saw blade with a new one. 2. Verify that the saw blade is properly inserted and securely locked in place. Follow the steps mentioned earlier to insert and remove the saw blade correctly. 3. Clean the saw blade and remove any debris or buildup that may be affecting its cutting performance. Use a brush or compressed air to remove dust, wood chips, or other particles. 4. Adjust the cutting depth of the saw blade. Make sure it is set to the appropriate depth for the material you are cutting. Refer to the depth adjustment instructions in the manual. 5. Ensure that the battery is fully charged. A low battery charge can affect the power and performance of the saw blade. Charge the battery as needed. 6. If the issue persists, consult the troubleshooting section of the manual for further guidance or contact Bosch customer support for assistance. By following these steps, you can address common issues related to the saw blade not cutting properly on the Bosch UniversalSaw 18V-100.
To properly use the glide shoe on the Bosch UniversalSaw 18V-100 to protect sensitive surfaces, follow these steps: 1. Ensure that the power tool is switched off and the battery is removed for safety. 2. Locate the glide shoe, which is a protective accessory that prevents scratching or damaging sensitive surfaces during cutting. 3. Position the glide shoe by hooking it to the front of the base plate of the power tool. 4. Push the glide shoe up at the back and allow it to click into place securely. 5. When using the glide shoe, do not use the saw blade storage compartment or the Cut Control feature. By following these steps, you can properly attach and use the glide shoe on the Bosch UniversalSaw 18V-100 to protect sensitive surfaces during cutting. This accessory helps prevent scratches and damage, ensuring a clean and smooth cutting experience.
To attach and use the anti-splinter guard accessory on the Bosch UniversalSaw 18V-100, follow these steps: 1. Ensure that the power tool is switched off and the battery is removed for safety. 2. Locate the anti-splinter guard, which is a protective accessory that helps prevent splintering of the surface while sawing. 3. Insert the anti-splinter guard into the base plate of the power tool from below, with the groove facing upwards. 4. Push the anti-splinter guard firmly into place until it is securely attached to the base plate. 5. When using the power tool, position the anti-splinter guard in such a way that it covers the area where the saw blade will make contact with the surface. 6. The anti-splinter guard should be aligned with the cutting line to ensure accurate and clean cuts. By following these steps, you can properly attach and use the anti-splinter guard accessory on the Bosch UniversalSaw 18V-100. This accessory helps prevent splintering and ensures clean and precise cuts on sensitive surfaces.
Yes, the manual of the Bosch UniversalSaw 18V-100 is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Bosch and is the answer not in the manual?
Question and answer
Number of questions: 0