Bosch Serie 6 DWB97JP50 manual

Bosch Serie 6 DWB97JP50
8.9 · 1
PDF manual
 · 20 pages
English
manualBosch Serie 6 DWB97JP50

3FHJTUFS

\RXU
QHZGHYLFHRQ
0\%RVFKQRZDQG
JHWIUHHEHQHILWV

CPTDIIPNFDPN

XFMDPNF

[en] Instructions for installation and use Extractor hood

Extractor hood

View the manual for the Bosch Serie 6 DWB97JP50 here, for free. This manual comes under the category exhaust hoods and has been rated by 1 people with an average of a 8.9. This manual is available in the following languages: English. Do you have a question about the Bosch Serie 6 DWB97JP50 or do you need help? Ask your question here

Need help?

Do you have a question about the Bosch and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

General
BrandBosch
ModelSerie 6 DWB97JP50 | DWB97JP50
Productexhaust hood
EAN4242005086610
LanguageEnglish
FiletypeUser manual (PDF), Datasheet (PDF), Energy label (PDF)
Performance
Fluid dynamic efficiency classA
Lighting efficiency classA
Grease filtering efficiency classB
Number of speeds3
Intensive speedYes
Maximum extraction power702 m³/h
Type of extractionDucted/Recirculating
Noise level55 dB
Noise level (low speed)42 dB
Pressure (Pa)314
Noise level (medium speed)45 dB
Minimum distance from electric hob550 mm
Minimum distance from gas hob650 mm
Maximum recirculating power378 m³/h
Power
Energy efficiency classA
Annual energy consumption34 kWh
Connected load145 W
AC input frequency50 - 60 Hz
Motor power140 W
AC input voltage220 - 240 V
Design
TypeWall-mounted
Built-in displayYes
Control typeTouch
Check valveYes
Product colorStainless steel
Exhaust connection diameter150 mm
Housing materialMetal
Motor includedYes
Number of motors1
Cord length1.3 m
CertificationCE, VDE
Exhaust locationTop
Filtering
Grease filter typeStainless steel
Washable filterYes
Filter cleaning indicatorYes
Lighting
Dimmable lightingYes
Illuminance359 lx
Number of bulbs3 bulb(s)
Bulb power1.66 W
Bulb typeLED
Lighting positionFront
Weight & dimensions
Width900 mm
Depth500 mm
Height without chimney46 mm
Weight19663 g
Height (min)628 mm
Height (max)1044 mm
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Bosch Serie 6 DWB97JP50 below.

What is the weight of the Bosch Serie 6 DWB97JP50?

The Bosch Serie 6 DWB97JP50 has a weight of 19663 g.

What certifications does the Bosch Serie 6 DWB97JP50 have?

The Bosch Serie 6 DWB97JP50 has the following certifications: CE, VDE.

When should I replace the carbon filter on my extractor hood?

The carbon filter should be replaced every three to twelve months.

How often should I clean the metal hood grease filters?

The metal grease filters should be cleaned every eight to ten weeks.

Where can I find the model number of my cooker ectractor hood?

The model number of the hood is usually found on a white label inside the hood.

What is the width of the Bosch Serie 6 DWB97JP50?

The Bosch Serie 6 DWB97JP50 has a width of 900 mm.

What is the depth of the Bosch Serie 6 DWB97JP50?

The Bosch Serie 6 DWB97JP50 has a depth of 500 mm.

What energy label does the Bosch Serie 6 DWB97JP50 have?

The Bosch Serie 6 DWB97JP50 has energy label A.

Is the fluid dynamic efficiency class of the Bosch Serie 6 DWB97JP50 rated A?

Yes, the fluid dynamic efficiency class of the Bosch Serie 6 DWB97JP50 is rated A. This means that it has excellent fluid dynamic efficiency, resulting in better ventilation performance and energy savings for the user.

Does the Bosch Serie 6 DWB97JP50 have a washable filter?

Yes, the Bosch Serie 6 DWB97JP50 has a washable filter. This allows for easy maintenance and cost savings, as the user can clean and reuse the filter instead of constantly replacing it.

Is the lighting efficiency class of the Bosch Serie 6 DWB97JP50 rated A?

Yes, the lighting efficiency class of the Bosch Serie 6 DWB97JP50 is rated A. This indicates that it provides high-quality lighting while consuming less energy. The user will enjoy bright and efficient lighting in their kitchen.

Does the Bosch Serie 6 DWB97JP50 have a built-in display?

Yes, the Bosch Serie 6 DWB97JP50 has a built-in display. This feature allows for easy control and monitoring of the hood's settings, enhancing user convenience and customization options.

Is the noise level of the Bosch Serie 6 DWB97JP50 55 dB?

Yes, the noise level of the Bosch Serie 6 DWB97JP50 is 55 dB. This is considered relatively low, ensuring quieter operation and a more pleasant cooking experience for the user.

How can I adjust the fan speed of the Bosch Serie 6 DWB97JP50 exhaust hood?

To adjust the fan speed of the Bosch Serie 6 DWB97JP50 exhaust hood, follow these steps: 1. Locate the control panel of the exhaust hood. 2. To switch on the fan, touch the "#" symbol. The fan will start at fan setting 2. 3. To select a different fan setting, touch symbol 1, 2, or 3 on the control panel. 4. To switch off the fan, touch the "#" symbol again. Additionally, the exhaust hood has some additional features related to fan speed: - Intensive setting: If there is a large build-up of odors and fumes/vapors, you can use the intensive setting. To activate it, touch the "C" or "D" symbol. After approximately 6 minutes, the exhaust hood will automatically switch back to fan setting 3. - Fan run-on time: To activate the fan run-on time, touch the "y" symbol. The fan will run at fan setting 1. After approximately 10 minutes, the fan will switch itself off automatically. To stop the fan run-on immediately, touch the "y" symbol again. Remember to adjust the fan speed according to your needs for effective ventilation.

Why is the exhaust hood not switching off when not in use?

The exhaust hood may not be switching off when not in use due to the following reasons: 1. Timer settings: Check if the exhaust hood has a timer function enabled. If the timer is set, the hood will continue running until the set time expires. Disable the timer function if not needed. 2. Intensive mode: The exhaust hood may be in intensive mode, which keeps the fan running at a higher speed for a certain period. To switch off the intensive mode, touch the symbol for the required fan setting. 3. Fan run-on time: The exhaust hood may have the fan run-on time feature activated. This feature keeps the fan running for a set duration after cooking to remove residual odors. Wait for the fan run-on time to complete, or touch the symbol to stop the fan run-on immediately. 4. Faulty control panel: If none of the above steps resolve the issue, there may be a problem with the control panel. Contact customer support or a qualified technician for further assistance. Remember to always follow the safety precautions mentioned in the manual and consult a professional if you are unsure about any troubleshooting steps.

How do I clean and replace the filter of the exhaust hood?

To clean and replace the filter of the Bosch Serie 6 DWB97JP50 exhaust hood, follow these steps: 1. Removing the metal grease filter: a. Open the lock and swing down the metal grease filter. b. Take hold of the metal grease filter from underneath and remove it from the holder. 2. Cleaning the metal grease filter: a. Soak the metal grease filter in hot soapy water. b. Clean the filter with a brush and rinse it thoroughly. c. Leave the metal grease filter to drain on an absorbent material. 3. Cleaning the metal grease filter holder: a. Use a damp cloth to clean the metal grease filter holder inside the appliance. 4. Replacing the activated charcoal filter (if applicable): a. If the exhaust hood has an activated charcoal filter, it needs to be replaced. Refer to the manual for specific instructions on how to replace the activated charcoal filter. 5. Reinstalling the metal grease filter: a. Place the cleaned metal grease filter back into the holder. b. Swing the metal grease filter back up and lock it into place. Remember to clean the metal grease filter regularly, approximately every 2 months, to prevent the risk of fire. Do not operate the exhaust hood without a grease filter. If you have any doubts or questions, consult the manual or contact customer support for assistance.

How do I switch between the exhaust air mode and circulating-air mode?

To switch between the exhaust air mode and circulating-air mode on the Bosch Serie 6 DWB97JP50 exhaust hood, follow these steps: 1. Exhaust air mode: a. Ensure that the exhaust hood is properly installed and connected to an external exhaust duct. b. Set the fan speed to the desired level using the control panel. c. When cooking, the exhaust hood will extract the air and expel it outside through the exhaust duct. 2. Circulating-air mode: a. If you do not have an external exhaust duct or prefer to recirculate the air, you can use the circulating-air mode. b. Install an activated carbon filter in the exhaust hood. Refer to the manual for specific instructions on how to install the filter. c. Set the fan speed to the desired level using the control panel. d. When cooking, the exhaust hood will filter the air through the activated carbon filter and recirculate it back into the kitchen. Remember to regularly clean or replace the activated carbon filter in the circulating-air mode to maintain its effectiveness. Consult the manual for detailed instructions on filter maintenance and replacement.

Why is the fan not working when I try to operate the exhaust hood?

If the fan is not working when you try to operate the Bosch Serie 6 DWB97JP50 exhaust hood, there could be several reasons for this issue. Follow these steps to troubleshoot the problem: 1. Check the power supply: Ensure that the exhaust hood is properly connected to a power source. Check if the power cord is securely plugged into the outlet. 2. Check the control panel: Make sure that the control panel is functioning correctly. Check if any buttons or settings are stuck or unresponsive. If necessary, clean the control panel with a soft, damp cloth. 3. Check the circuit breaker: Verify if the circuit breaker or fuse for the exhaust hood is tripped or blown. Reset the circuit breaker or replace the fuse if needed. 4. Check the fan motor: If the above steps do not resolve the issue, there may be a problem with the fan motor. Contact customer support or a qualified technician for further assistance. Remember to always follow safety precautions when troubleshooting electrical appliances. If you are unsure or uncomfortable with any of the steps, it is recommended to seek professional help.

How do I install an activated carbon filter for odour binding in circulating-air mode?

To install an activated carbon filter for odor binding in circulating-air mode on the Bosch Serie 6 DWB97JP50 exhaust hood, follow these steps: 1. Ensure that the exhaust hood is switched off and unplugged from the power source. 2. Open the metal grease filter by releasing the lock and swinging it down. 3. Locate the filter compartment at the back of the exhaust hood. 4. Insert the activated carbon filter into the filter compartment, ensuring that it is securely in place. 5. Close the metal grease filter by swinging it back up and locking it into position. 6. Verify that the activated carbon filter is properly installed by checking if it is securely held in the filter compartment. 7. Plug the exhaust hood back into the power source. Remember to replace the activated carbon filter regularly, as recommended in the manual, to maintain its effectiveness in odor binding. Consult the manual for specific instructions on filter replacement and maintenance.

What does the symbol on the metal grease filter/activated charcoal filter saturation indicator mean?

The symbol on the metal grease filter/activated charcoal filter saturation indicator of the Bosch Serie 6 DWB97JP50 exhaust hood indicates the saturation level of the filters. Here is what the symbols mean: - Metal grease filters: The symbol "#" and the number "1" will flash if the metal grease filters are saturated and need cleaning. - Activated charcoal filter: The symbol "#" and the number "2" will flash if the activated charcoal filter is saturated and needs replacement. - Metal grease filters and activated charcoal filter: The symbols "#", "1", and "2" will flash together if both the metal grease filters and the activated charcoal filter are saturated and need cleaning/replacement. When the saturation indicators are flashing, it is recommended to clean the metal grease filters or replace the activated charcoal filter. The saturation indicators can be reset by touching the appropriate symbol. Note that the saturation indicator does not apply to non-renewable activated charcoal filters that are inserted downstream of the metal grease filter. These filters must be replaced twice a year. Refer to the "Cleaning and maintenance" section in the manual for detailed instructions on cleaning the filters and replacing the activated charcoal filter.

How do I switch on and off the lighting of the exhaust hood independently of the fan?

To switch on and off the lighting of the Bosch Serie 6 DWB97JP50 exhaust hood independently of the fan, follow these steps: 1. Locate the control panel of the exhaust hood. 2. To switch on the lighting, look for the symbol that represents the lighting function. It is usually depicted as a light bulb or a sun icon. Touch or press this symbol to switch on the lighting. 3. To adjust the brightness of the lighting, if applicable, look for the symbols that represent brightness levels. These symbols may be depicted as a sun icon with different intensity levels. Touch or press the symbol corresponding to the desired brightness level. 4. To switch off the lighting, touch or press the lighting symbol again. The lighting will turn off independently of the fan. Note: The specific location and appearance of the control panel symbols may vary slightly depending on the model. Refer to the manual for the exact symbols and their locations on the control panel. Remember to handle the lighting controls with care and avoid touching them with wet hands or when the exhaust hood is in use.

Why is the lighting not turning on/off when I try to control it?

If the lighting of the Bosch Serie 6 DWB97JP50 exhaust hood is not turning on/off when you try to control it, there could be a few possible reasons for this issue. Follow these steps to troubleshoot the problem: 1. Check the power supply: Ensure that the exhaust hood is properly connected to a power source. Check if the power cord is securely plugged into the outlet. 2. Check the control panel: Make sure that the control panel is functioning correctly. Check if any buttons or settings related to the lighting function are stuck or unresponsive. If necessary, clean the control panel with a soft, damp cloth. 3. Check the light bulb: Verify if the light bulb is properly installed and not burnt out. Turn off the exhaust hood and allow the bulb to cool down before checking. If the bulb is burnt out, replace it with a new one of the same type and wattage. 4. Check the wiring: If the above steps do not resolve the issue, there may be a problem with the wiring or electrical connections. Contact customer support or a qualified technician for further assistance. Remember to always follow safety precautions when troubleshooting electrical appliances. If you are unsure or uncomfortable with any of the steps, it is recommended to seek professional help.

How do I adjust the brightness of the lighting of the exhaust hood?

To adjust the brightness of the lighting on the Bosch Serie 6 DWB97JP50 exhaust hood, follow these steps: 1. Locate the control panel of the exhaust hood. 2. Look for the symbol that represents the lighting function. It is usually depicted as a light bulb or a sun icon. 3. Touch or press the lighting symbol to switch on the lighting. 4. Once the lighting is switched on, look for symbols that represent different brightness levels. These symbols may be depicted as a sun icon with different intensity levels. 5. Touch or press the symbol corresponding to the desired brightness level. The lighting will adjust accordingly. 6. If you want to change the brightness level again, simply touch or press the symbol for the new desired level. Note: The specific location and appearance of the control panel symbols may vary slightly depending on the model. Refer to the manual for the exact symbols and their locations on the control panel. Remember to handle the lighting controls with care and avoid touching them with wet hands or when the exhaust hood is in use.

Is the manual of the Bosch Serie 6 DWB97JP50 available in English?

Yes, the manual of the Bosch Serie 6 DWB97JP50 is available in English .

Is your question not listed? Ask your question here

No results