Dryer housing, control panel– Wipe clean with a soft, damp cloth.– Do not clean with a water jet.– Remove detergent and cleaning agent residue immediately.– During drying, water may occasionally accumulate between the window and the seal. This does not affect the proper operation of your dryer.Heat exchangerThe heat exchanger requires cleaning once a month, however this varies depending on how frequently the dryer is used.Allow the dryer to cool down and place an absorbent cloth under the maintenance flap.Residual water may escape.1. Unlock the maintenance flap and open completely.2. Turn both locking levers towards each another.3. Pull out the cap.4. Remove the heat exchanger.Take care not to damage the heat exchanger.When cleaning, use water only. Do not use hard or sharp-edged objects.5. Rinse the heat exchanger and the cap on all sides with a jet of water to completely remove all of the fluff.6. Remove any fluff from the seals on the dryer and heat exchanger.7. Allow to drip dry fully.8. First insert the heat exchanger, then the cap.
9.
Turn back both locking levers and close the maintenance flap until it locks closed.Moisture sensorsThe dryer is equipped with stainless steel moisture sensors.Moisture sensors measure the moisture level of the laundry.After sustained, repeated operation, a fine layer of limescale may form on the moisture sensors.1. Open the door.2. Clean the moisture sensors with a damp sponge which has a rough surface.Do not use steel wool or abrasive agents!Only when switched off!
9
Installation
–Scope of delivery: dryer, operating and installation instructions, basket for woollens (depending on
the model).
–Check the dryer for transport damage.
–The dryer is very heavy. Do not attempt to lift it on your own.
–Be careful to avoid sharp edges.
–Do not lift the dryer by protruding parts (e.g. the door) - risk of breakage.
–Do not set up in a room that is susceptible to frost. Freezing water may cause damage.
–If in doubt, have the appliance connected by a specialist.
Setting up the dryer
–The mains plug must always be accessible.
–Ensure that the appliance is placed on a clean, level and
firm surface.
–Do not obstruct the air inlet on the dryer.
–Keep the area around the dryer clean.
–Level the dryer using the threaded feet
and a spirit level.
Never remove the threaded feet!
For mains connection, see Safety instructions a page 13.
–Connect to an AC earthed socket. If in doubt have the socket checked by a specialist.
–The mains voltage and the voltage shown on the rating plate (apage 10) must be the same.
–The connected load and necessary fuse protection are specified on the rating plate.
Converting the installed loadNote the fuse protection of the socket (16/10 Amps.).
1.Turn the programme selector to Off.
2.Press and hold the yAjuste secado(Fine adjust) button.
3.Turn the programme selector to Algodón (Cotton) Extra seco para guardar
(Cupboard Dry Extra);wait until the recent setting appears in the display:
¥¯=10A or ³=16A.
4.Press the yAjuste secado(Fine adjust) button to change the settings.
5.Turn the programme selector to Off.
The values for the energy label are determined using a circuit breaker/fuse rating of 16 A. If the circuit
breaker/fuse rating is changed to 10 A, the drying time and energy consumption will be higher. You
can find details on this in the consumption values table. a page 10.
Frost protection/transport
Preparation
1.Empty the condensate container apage 4/11.
2. Select any programme using the programme selector.
3.Press the Inicio/Stop(Start/Pause) button a condensation is pumped into the container.
4.Wait several minutes or until the dryer stops, and then empty the condensate container again.
5.Turn the programme selector to Off.
1.
Take all accessory parts out of
the drum.
The drum must be empty.
Make sure that the air inlet
remains unobstructed
Clean and level
Do not install the dryer behind a door
or sliding door which could prevent or obstruct
the dryer door from opening.
This will prevent children from locking
themselves in and risking their lives.
If you wish, you can operate the appliance with the
drain hose connected. a Separate Condensation
drain instructions (for the model you have).
2.
3.
Do not operate the dryer if
there is a risk of frost.
10
Optional accessories(order from the after-sales service using the order number, depending on the model)
Washer-dryer stack connection set
The dryer can be placed on top of a suitable washing machine with the same width and depth to save space. The dryer must be fastened
to the washing machine using this connection set. WTZ 11400: with pull-out worktop.
Platform
For easier loading and unloading. The basket contained in the drawer can be used to carry the laundry.
Woollens basket
For drying individual wollen fabrics, sports shoes and soft toys (see separate instructions for “Woollens basket”).
Technical data
ʠ
Dimensions (DxWxH)60 x 60 x 85 cm (height adjustable)
Weightapprox. 45 kg
Max. capacity7 kg
Condensate container4.2 l
Connection voltage220-240 V
Connected load2800 / 2100 W
Fuse protection16 A / 10 A
Ambient temperature5-35°C
Product number
Production number
Inside of door
The rating plate can be found on the back of the dryer.
Power consumption when switched off0.10 W
Power consumption when ready for use (left-on mode)1.00 W
ʠ
Drum interior light (depending on model): The drum lights up after the door is opened and after the programme starts, and switches off
*Programme setting for testing in accordance with the applicable EN61121 standard.
**The values may differ from those specified, depending on the type of fabric, composition of laundry to be dried, residual moisture in the laundry,
the degree of dryness that has been set, the amount of laundry being loaded, the environmental conditions, and any additional functions that
have been activated.
Most efficient programme for cotton fabrics
The following "standard cottons programme" (identified with ) is suitable for drying normal, wet cotton laundry and is most efficient in terms of
its combined energy consumption for drying wet cotton laundry.
Programas estándar para algodón según el Reglamento Europeo 932/2012 vigente
ProgrammeLoadEnergy consumptionProgramme duration
Cottons
Cupboard Dry
7 kg/3.5 kg
16 A16 A
4.08 kWh/2,33 kWh111 min/69 min
Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU.
The consumption values are determined using a circuit breaker/fuse rating of 16 A.
WTZ
20410
WMZ
20500
WMZ
20600
10
11
What to do if ...
Turn the programme selector to Off and remove the mains plug from the socket.
ʠ
The Inicio/Stop(Start/Pause) indicator light does not light up.Mains plug plugged in?Programme selected?Check the socket fuse.
ʠ
The display panel light and indicator lights (depending on
model) go out and the Inicio/Stop
(Start/Pause)indicator light flashes.Energy-saving mode is activated a see the separate Energy-saving mode instructions.
ʠ
The display panel switches off.The appliance goes into the sleep mode after activating
Terminado en/em(Finished in) option apage 5.
ʠ
The Í(Condensate container) indicator light flashes.
Empty the condensate container apage 4.
Press the Inicio/Stop(Start/Pause) button to reset the
displayed indication and then press the Inicio/Stop(Start/Pause) button again to restart the appliance if necessary.If the condensation drain hose is connected, check it and, if necessary, clean it.
Press the Inicio/Stop(Start/Pause) button to reset the
displayed indication and then press the Inicio/Stop(Start/Pause) button again to restart the appliance if necessary.
Clean the heat exchangera page 8.
ʠ
Dryer does not start.Inicio/Stop(Start/Pause) button selected?
Door closed?Ambient temperature greater than 5°C? The optimum ambient temperature for drying is between 5 °C and 35 °C.
After-sales service
If you cannot rectify the fault yourself (e.g. switching off/on) aWhat to do if..., page 11/12,
please contact our after-sales service. We will always find an appropriate solution and avoid unnecessary visits by engineers.
The contact details of your local after-sales service can be found in the enclosed after-sales
service directory.– GB 0344 892 8979 (Calls charged at local or mobile rate.)
–IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.)
Please provide the after-sales service the product number (E no.) and the production number (FD) of the appliance.Product number Production numberYou can find this information:inside the door* / in the opened service flap* and on the rear of the appliance.*depending on the modelTrust the expertise of the manufacturer. Contact us for assistance. In this way, you can rest assured that the repair will be carried out by trained service technicians using original spare parts.
12
What to do if ...
ʠ
Programme terminates shortly after starting.Is the appliance loaded with the laundry?Load too small for selected programme?/Use timed programme apage 6/7.Loaded laundry dry?
ʠ
Water is leaking out.Make sure the dryer is level.Clean the heat exchanger seal.
ʠ
The door opens by itself.Push the door closed until you hear it engage.
ʠ
Creasing.Laundry load exceeded?Remove articles of clothing immediately after the end of the programme, hang up and pull into shape.Unsuitable programme selected a page 7.
ʠ
Laundry is not dried correctly or is still too damp.After the end of the programme, warm laundry feels damper than it actually is. Spread the laundry out and allow the heat to disperse.Finely adjust the dryness level – this extends the drying time but does not increase the temperature. Your laundry will become drier.Select a programme with a longer drying time or increase the drying level. This does not increase the temperature.Select a time programme for extended drying of laundry that is still damp.If you have exceeded the maximum load for the programme, the laundry may not be dried correctly.Clean the moisture sensor in the drum. A fine layer of limescale may adversely affect the performance of the sensors and your washing will not dry properly.Drying has been interrupted as a result of a power cut, because the condensate container is full or because the maximum drying time has been exceeded.
ʠ
Drying time too long.Clean the fluff filter under running water a page 4/11.
Insufficient supply of air a Ensure that air can circulate.
Air inlet possibly blocked a Clear inlet apage 9.
Ambient temperature higher than 35°C a Ventilate the room. The optimum ambient temperature for drying is between 5 °C and 35 °C. Outside of this range, the drying time may increase.
ʠ
One or more indicator lights are flashing.
Clean the fluff filter and heat exchanger apage 4,8/11.
Check the installation conditions apage 9.
Switch off, allow to cool, switch back on and restart the programme.
ʠ
Power failure.Remove the laundry from the dryer immediately and spread out. This allows the heat to dissipate. Be careful as the door, the drum and the laundry may be hot.
13
Safety instructions
Emergency
–Pull the appliance plug out of the socket immediately or disconnect the fuse.
ONLY use the
dryer...
–in rooms inside the house.
–to dry fabrics.
The dryer
must
NEVER...
–be used for purposes other than those described above.
–be modified in terms of its technology or properties.
Hazards
–The dryer must not be used by children or persons who have not been instructed in
its use.
–Do not leave children unsupervised near the dryer.
–Keep pets away from the dryer.
–Remove all objects from pockets, and lighters in particular a Risk of explosion.
–Do not lean or sit on the door a Risk of tipping.
Installation
–Secure loose cables a Risk of tripping.
–Do not operate a dryer if there is a risk of frost.
Mains
connection
–Connect the dryer to an AC earthed socket according to specifications, otherwise it
cannot be guaranteed that the appliance is completely safe.
–The cable cross-section must be sufficient.
–Only use earth-leakage circuit breakers with the following symbol:
–The appliance plug and socket must be compatible.
–Do not use multiple plugs/connectors and/or extension cables.
–Do not touch or hold the appliance plug with wet hands a Risk of electric shock.
–Never pull the appliance plug out of the socket by its cable.
–Do not damage the mains lead a Risk of electric shock.
Operation
–Only load the drum with laundry. Check the contents before you switch the dryer on.
–Do not use the dryer if the laundry has been in contact with solvents, oil, wax, grease
or paint (e.g. hair setting spray, nail polish remover, stain remover, cleaning solvent,
etc.) a fire/explosion hazard.
–The tumble dryer is not to be used if industrial chemicals have been used for
cleaning.
–Dust (e.g. coal dust, flour) poses a danger: do not use the dryer aexplosion
hazard.
–Do not turn off the dryer until the drying process ends, unless the laundry will be
removed quickly and spread out, so that the heat can dissipate.
–Do not put laundry containing foamed material/rubber in the dryer a elastic
material may be destroyed and the dryer may be damaged due to possible
deformation of the foamed material.
–When cleaning the fluff filter, make sure that no foreign material (down or filling
material) gets into the air duct opening. If necessary, clean the drum beforehand with
a vacuum cleaner. If foreign material should still get into the air duct a call the after-
sales service a Risk of fire/explosion.
–Light things, such as long hair, may be sucked into the air inlet of the dryer aRisk
of injury.
–Final part of a tumble dryer cycle occurs without heat (cool down cycle), to ensure
that the items are left at a temperature that ensures that the items will not be
damaged.
–Switch off the dryer once the programme has ended.
–The exterior of the appliance's rear panel becomes very hot during
operation. Never touch the hot surface of the appliance's rear panel. Keep
children away from the appliance a Risk of burns!
–The water from condensation is not drinking water and may be
contaminated with fluff.
Defect
–Do not use the dryer if it is defective or if you suspect that it is. Repairs must only be
carried out by the after-sales service.
–Do not use the dryer if the mains cable is defective. To avoid danger, only have the
defective mains cable replaced by the after-sales service.
Spare parts
–For safety reasons, you must only use genuine spare parts and accessories.
Disposal
–Pull out the appliance plug, then cut off the mains cable from the appliance. Dispose
of the appliance at a municipal waste disposal site.
–Packaging: Keep all packaging out of reach of babies and children a Risk
of suffocation.
–All materials are environmentally sound and can be reused. Dispose of them in an
environmentally-responsible manner.
enInstruction manualDryerWTB86238EE
View the manual for the Bosch Serie | 4 WTB86238EE here, for free. This manual comes under the category dryers and has been rated by 31 people with an average of a 7.9. This manual is available in the following languages: English. Do you have a question about the Bosch Serie | 4 WTB86238EE or do you need help? Ask your question here
Need help?
Do you have a question about the Bosch and is the answer not in the manual?
Receive updates on solutions
Get answers to your question
Question and answer
Number of questions: 36
J
JustynaAugust 10, 2020
Hello, I have a problem with the dryer. I can't start it, there is a key, a feather, and a star displayed on the screen. When I try to turn it on, it beeps. I have no idea what is going on, it has never done this before. Please help.
This message has been automatically translated
M
Martha RodríguezJanuary 8, 2021
Why does my Bosch Serie 4 dryer, when it is drying, reduce the drying time from one hour to minutes and doesn't dry my clothes properly? This happens in all programs.
This message has been automatically translated
R
Rosario Montilla Córdoba January 26, 2021
My dryer stops and the clothes are not dry, the tank light comes on and the tank is empty, what is happening to it?
This message has been automatically translated
R
RosaApril 18, 2021
For four years the dryer has worked great, but for a month now it doesn't completely dry the clothes, which come out damp.
View photoThis message has been automatically translated
C
Claus IversenNovember 15, 2021
We have had our Condenser for a couple of years. Now it keeps saying that it is filled with water although it is not. After runing for a short period, it shows the symbol for 'filled with water'.
How do I fix this?
To fix the issue of your Bosch Serie | 4 WTB86238EE dryer displaying the symbol for 'filled with water' even though it is not actually filled with water, you can try the following steps:
1. Turn off the dryer and unplug it from the power source.
2. Check the condensate container located inside the dryer. If it is full, empty the container and ensure it is properly inserted back into place.
3. Clean the fluff filter after each drying cycle to prevent any blockages. Open the door of the dryer, remove any fluff from around the door and pull out the fluff filter. Remove the fluff from the shaft of the filter and sweep your hand over the filter to remove any remaining fluff. If the filter is very dirty, you can rinse it with warm water and dry it thoroughly before reinserting it.
4. Check the display panel for any error codes or flashing lights. If the Í (Condensate container) indicator light is flashing, it means the condensate container needs to be emptied. Empty the container and press the Start/Pause button to reset the indication.
5. Once you have completed these steps, plug the dryer back in and turn it on. Run a short drying cycle to see if the issue persists.
This answer is automatically generated
M
Me ProsApril 4, 2023
Hope this help
C
Claudia February 23, 2020
If a drawing of a flashing key is turned on and it doesn't start, could you tell me what's wrong?
This message has been automatically translated
M
Marianne ErlbacherJune 26, 2019
On my Bosch Serie | 4 WTB86238EE dryer, the key on the display lights up and beeps. Can someone please help me?
This message has been automatically translated
A
AntoinetteApril 15, 2021
What does this symbol mean?
View photoThis message has been automatically translated
T
Theresa Morck March 9, 2023
My Bosch series 4 tumble dry has two warning lights on …. The key and the sun . It is not switching on .
The Bosch Serie | 4 WTB86238EE is a freestanding dryer with a condensation drying system. It meets the CE and VDE certification standards, ensuring its compliance with safety and quality regulations. The appliance features a built-in display and is controlled using a rotary control type.
With a maximum delay start time of 24 hours, this dryer offers flexibility in managing laundry cycles. It has a rated capacity of 7 kg, providing ample space for drying clothes. The drying class is B, indicating its energy efficiency.
The cycle time for this dryer is 111 minutes, which may vary depending on the selected program and load size. The noise level of the machine during operation is 65 dB, enabling a relatively quiet drying experience.
The adjustable drying level feature allows users to customize the drying process according to their preferences. Additionally, the delayed start timer enables users to schedule the drying cycle to start at a later time.
This dryer also includes an LED program stage indicator, providing clear feedback on the ongoing drying process. It helps users keep track of the current stage, ensuring efficient usage.
Overall, the Bosch Serie | 4 WTB86238EE offers a reliable and durable drying solution. With its advanced features and user-friendly design, it provides effective drying performance.
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Bosch Serie | 4 WTB86238EE below.
What is a condenser dryer?
A condenser dryer is a dryer in which condensation ends up in a reservoir.
What is a drain dryer?
A drain dryer is a dryer in which the warm air and condensation are drained through a hose.
What is the best thing to do about a smelly dryer?
It is best to wipe the dryer drum with a damp cloth and some lemon cleaner.
There is a burning smell from my dryer, now what?
Check the following: - That the fluff filter is clean. - That the bottom of the dryer is free of dust. - That the drain hose is clean. If the above does not help, a mechanic should be called in.
What is the weight of the Bosch Serie | 4 WTB86238EE?
The Bosch Serie | 4 WTB86238EE has a weight of 42000 g.
What certifications does the Bosch Serie | 4 WTB86238EE have?
The Bosch Serie | 4 WTB86238EE has the following certifications: CE, VDE.
What is the height of the Bosch Serie | 4 WTB86238EE?
The Bosch Serie | 4 WTB86238EE has a height of 842 mm.
What is the width of the Bosch Serie | 4 WTB86238EE?
The Bosch Serie | 4 WTB86238EE has a width of 598 mm.
What is the depth of the Bosch Serie | 4 WTB86238EE?
The Bosch Serie | 4 WTB86238EE has a depth of 599 mm.
What energy label does the Bosch Serie | 4 WTB86238EE have?
The Bosch Serie | 4 WTB86238EE has energy label B.
How do I adjust the drying time on my Bosch Serie | 4 WTB86238EE dryer?
To adjust the drying time, simply turn the program selector to the desired drying cycle and then use the time selector knob to increase or decrease the drying time as needed.
What should I do if my dryer is not heating up?
If your dryer is not heating up, make sure that the power cord is securely plugged into a working outlet. Additionally, check if the dryer's circuit breaker or fuse has tripped. If all is well, there may be an issue with the heating element or thermostat, and it is recommended to contact a professional for further assistance.
How can I clean the lint filter in my Bosch Serie | 4 WTB86238EE dryer?
To clean the lint filter, simply open the dryer door and locate the filter near the bottom of the opening. Pull the filter out and remove any lint or debris accumulated on it. Once clean, slide the filter back into its place, ensuring it is properly seated.
Can I override the automatic sensor drying feature on my dryer?
Yes, the automatic sensor drying feature can be overridden if needed. You can select the desired drying cycle manually and then adjust the drying time using the time selector knob. This allows you to tailor the drying process according to your preferences.
How can I check if my dryer's exhaust vent is blocked?
To check for a blocked exhaust vent, start by disconnecting the dryer from the power source. Then, locate the exhaust vent on the back of the dryer and carefully detach the vent hose. Inspect the vent and remove any lint or debris that may be blocking it. Additionally, ensure that the vent hose is not kinked or crushed when reattaching it to the dryer.
Does the Bosch Serie | 4 WTB86238EE have a freestanding placement?
Yes, the Bosch Serie | 4 WTB86238EE has a freestanding placement. This means that it is not built into a wall or cabinet and can be placed anywhere in the room.
What is the drying system of the Bosch Serie | 4 WTB86238EE?
The drying system of the Bosch Serie | 4 WTB86238EE is condensation. This means that it collects moisture from the clothes and turns it into water, which can then be emptied manually or through a connected drain.
Does the Bosch Serie | 4 WTB86238EE have a built-in display?
Yes, the Bosch Serie | 4 WTB86238EE has a built-in display. This allows the user to easily see and control the settings and progress of the drying cycle.
What is the control type of the Bosch Serie | 4 WTB86238EE?
The control type of the Bosch Serie | 4 WTB86238EE is rotary. This means that it has a dial or knob that can be turned to select different settings and programs.
Can the Bosch Serie | 4 WTB86238EE be delayed to start later?
Yes, the Bosch Serie | 4 WTB86238EE can be delayed to start later. It has a delay start feature, allowing the user to set a time for the drying cycle to begin up to 24 hours in advance.
Is the manual of the Bosch Serie | 4 WTB86238EE available in English?
Yes, the manual of the Bosch Serie | 4 WTB86238EE is available in English .
Need help?
Do you have a question about the Bosch and is the answer not in the manual?
Question and answer
Number of questions: 36Hello, I have a problem with the dryer. I can't start it, there is a key, a feather, and a star displayed on the screen. When I try to turn it on, it beeps. I have no idea what is going on, it has never done this before. Please help.
This message has been automatically translatedWhy does my Bosch Serie 4 dryer, when it is drying, reduce the drying time from one hour to minutes and doesn't dry my clothes properly? This happens in all programs.
This message has been automatically translatedMy dryer stops and the clothes are not dry, the tank light comes on and the tank is empty, what is happening to it?
This message has been automatically translatedFor four years the dryer has worked great, but for a month now it doesn't completely dry the clothes, which come out damp.
We have had our Condenser for a couple of years. Now it keeps saying that it is filled with water although it is not. After runing for a short period, it shows the symbol for 'filled with water'. How do I fix this?
2 comments
To fix the issue of your Bosch Serie | 4 WTB86238EE dryer displaying the symbol for 'filled with water' even though it is not actually filled with water, you can try the following steps: 1. Turn off the dryer and unplug it from the power source. 2. Check the condensate container located inside the dryer. If it is full, empty the container and ensure it is properly inserted back into place. 3. Clean the fluff filter after each drying cycle to prevent any blockages. Open the door of the dryer, remove any fluff from around the door and pull out the fluff filter. Remove the fluff from the shaft of the filter and sweep your hand over the filter to remove any remaining fluff. If the filter is very dirty, you can rinse it with warm water and dry it thoroughly before reinserting it. 4. Check the display panel for any error codes or flashing lights. If the Í (Condensate container) indicator light is flashing, it means the condensate container needs to be emptied. Empty the container and press the Start/Pause button to reset the indication. 5. Once you have completed these steps, plug the dryer back in and turn it on. Run a short drying cycle to see if the issue persists.
This answer is automatically generatedHope this help
If a drawing of a flashing key is turned on and it doesn't start, could you tell me what's wrong?
This message has been automatically translatedOn my Bosch Serie | 4 WTB86238EE dryer, the key on the display lights up and beeps. Can someone please help me?
This message has been automatically translatedWhat does this symbol mean?
My Bosch series 4 tumble dry has two warning lights on …. The key and the sun . It is not switching on .