View the manual for the Bosch PSR 14,4 LI-2 here, for free. This manual comes under the category drill machines and has been rated by 7 people with an average of a 7.9. This manual is available in the following languages: English. Do you have a question about the Bosch PSR 14,4 LI-2 or do you need help? Ask your question here


| Brand | Bosch |
| Model | PSR 14,4 LI-2 | 0 603 973 408 |
| Product | drill machine |
| EAN | 3165140667401, 3165140785792 |
| Language | English |
| Filetype | User manual (PDF) |
| Maximum torque (soft applications) | 20 N⋅m |
| Idle speed (1st gear) | 390 RPM |
| Idle speed (2nd gear) | 1300 RPM |
| Screw diameter (max) | 8 mm |
| Drilling diameter in wood (max) | 30 mm |
| Drilling diameter in steel (max) | 10 mm |
| Maximum torque (hard applications) | 40 N⋅m |
| Vibration emission | 2.5 m/s² |
| Drilling, Screwdriving | |
| Product design | Pistol grip drill |
| Drilling | Yes |
| Screwdriving | Yes |
| Electronic Cell Protection (ECP) | Yes |
| Power source | Battery |
| Battery technology | Lithium-Ion (Li-Ion) |
| Battery voltage | 14.4 V |
| Weight | 1140 g |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Bosch PSR 14,4 LI-2 below.
1. Soak the rusty part in vinegar until completely soaked through. 2. Let the vinegar work on the rust for 24 hours. 3. Remove the rust with a wire brush or aluminium foil.
The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.
The amount of sound varies a lot per brand and type of drill machine, it is therefore wise to wear hearing protection to be sure.
The Bosch PSR 14,4 LI-2 has a weight of 1140 g.
Yes, this means that the drill machine has a built-in feature that protects the battery and extends its lifespan.
The maximum torque for soft applications is 20 N⋅m, which is relatively average compared to other drill machines.
Yes, the drill machine is capable of drilling in wood with a maximum diameter of 30 mm.
The idle speed in the 1st gear is 390 RPM, allowing for slower and more precise drilling or screwdriving.
The drill machine can handle a maximum screw diameter of 8 mm, which is suitable for most general screwdriving tasks.
To turn on the Bosch PSR 14,4 LI-2 drill machine, follow these steps: 1. Locate the on/off switch on the drill machine. It is labeled as the "på-/av-bryter" in the manual. 2. Press and hold the on/off switch to start the drill machine. The "Power Light" lamp, labeled as "lampen" in the manual, will illuminate when the switch is partially or fully pressed. 3. Release the on/off switch to turn off the drill machine. The "Power Light" lamp will turn off. Please note that the specific location and labeling of the on/off switch may vary slightly on the actual drill machine, but it should be similar to the description provided. Remember to always follow safety precautions and refer to the manual for detailed instructions and guidelines when using the Bosch PSR 14,4 LI-2 drill machine.
If the Bosch PSR 14,4 LI-2 drill machine does not start, you can try the following steps: 1. Check the battery: Ensure that the battery is properly inserted into the handle and fully charged. If the battery is low or not inserted correctly, the drill machine may not start. 2. Verify the on/off switch: Make sure that the on/off switch is in the "on" position. The switch should be pressed and held to start the drill machine. 3. Check for any obstructions: Inspect the drill chuck and ensure that there are no drill bits or other objects stuck in it. Remove any obstructions that may prevent the chuck from rotating. 4. Examine the power connection: Ensure that the power cord is securely connected to a power source. If using a cordless drill, make sure the battery is properly connected. 5. Contact customer support: If the drill machine still does not start after following these steps, it is recommended to contact Bosch customer support for further assistance. They can provide additional troubleshooting steps or arrange for repairs if necessary. Remember to always refer to the manual for specific instructions and safety guidelines when using the Bosch PSR 14,4 LI-2 drill machine.
To change the drill bit on the Bosch PSR 14,4 LI-2 drill machine, follow these steps: 1. Ensure that the drill machine is turned off and unplugged from the power source for safety. 2. Locate the securing screw on the drill chuck. It is usually located near the front of the chuck. 3. Use a screwdriver to loosen the securing screw by turning it counterclockwise. Apply some force if the screw is tightly seated. 4. Once the securing screw is loosened, hold the short end of an Allen key firmly and insert it into the keyless chuck. 5. Place the drill machine on a stable surface, such as a workbench, and hold it securely. 6. Rotate the Allen key in a counterclockwise direction to loosen the keyless chuck. If the chuck is tight, you can lightly tap the long end of the Allen key to help loosen it. 7. Remove the Allen key from the keyless chuck once it is fully loosened. 8. To install a new drill bit, insert the desired bit into the keyless chuck and tighten it by rotating the chuck in a clockwise direction. 9. Use the Allen key to tighten the securing screw by turning it clockwise. Ensure that the screw is securely tightened. 10. Your Bosch PSR 14,4 LI-2 drill machine is now ready for use with the new drill bit. Remember to always refer to the manual for specific instructions and safety guidelines when using the Bosch PSR 14,4 LI-2 drill machine.
If the drill bit gets stuck in the material while using the Bosch PSR 14,4 LI-2 drill machine, you can try the following steps: 1. Switch off the drill machine immediately to prevent any further damage or injury. 2. Ensure that the drill machine is unplugged from the power source for safety. 3. Examine the material and the drill bit to identify the cause of the jam. Look for any debris, obstructions, or irregularities that may be causing the drill bit to get stuck. 4. If there is any debris or dust around the drill bit, clean it using a brush or compressed air to remove any particles that may be causing the jam. 5. Gently try to reverse the drill direction by adjusting the rotational direction switch. Sometimes, changing the direction can help release the stuck drill bit. 6. If the drill bit is still stuck, carefully grip the chuck and rotate it manually in the opposite direction of drilling. This may help loosen the grip on the stuck drill bit. 7. If the above steps do not work, you may need to use pliers or a wrench to grip the drill bit and carefully twist it counterclockwise to remove it from the material. Remember to always prioritize safety and refer to the manual for specific instructions and safety guidelines when using the Bosch PSR 14,4 LI-2 drill machine.
To charge the battery of the Bosch PSR 14,4 LI-2 drill machine, follow these steps: 1. Ensure that the drill machine is turned off and unplugged from the power source. 2. Locate the battery on the drill machine. It is usually located at the bottom of the handle. 3. Remove the battery from the drill machine by pressing the battery unlocking button and pulling the battery out towards the rear. 4. Connect the battery to the appropriate battery charger. Refer to the accessories page in the manual for the recommended charger. 5. Plug the charger into a power outlet. 6. Wait for the battery to fully charge. The charging time may vary depending on the battery capacity and the charger used. Refer to the battery charge control indication section in the manual for information on how to check the charge condition of the battery. 7. Once the battery is fully charged, disconnect the charger from the power outlet. 8. Reinsert the charged battery into the drill machine by aligning it with the battery compartment and pushing it in until it clicks into place. 9. Your Bosch PSR 14,4 LI-2 drill machine is now ready to be used with the charged battery. Remember to always refer to the manual for specific instructions and safety guidelines when using the Bosch PSR 14,4 LI-2 drill machine.
Yes, the manual of the Bosch PSR 14,4 LI-2 is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Bosch and is the answer not in the manual?
Question and answer
Number of questions: 3I have a Bosch 14.4 autofeed drill and it won't turn on anymore. The lights turn on and flicker but it doesn't spin. What is the problem?
What batteries (by numbers) work with psr 14,4 LI-2 and the original charger?
1 comment
Sry ignore this question, wrong tab open. Have sent a direct mail instead.
How does the battery fit in the charger?