Bosch Logixx 7 WVH28421GB manual

Bosch Logixx 7 WVH28421GB
8.4 · 30
PDF manual
 · 8 pages
English
manualBosch Logixx 7 WVH28421GB
1

Safety instructions

The washer dryer is heavy  take care when lifting it.
Warning: frozen hoses may tear/burst. Do not install the washer dryer outdoors or in areas
where there is a risk of frost.
The washer dryer may be damaged. Do not lift by projecting components (e.g. washer dryer
door).
In addition to the instructions mentioned here, special regulations of the relevant water and
power supply companies may apply.
If in doubt, have the appliance connected by a technician.
Lay hoses and cables in such a way that there is no risk that they can be tripped over.

Environmental disposal

Dispose of packaging in an environmentally friendly manner.
This appliance has been identified in accordance with the European Directive
2002/96/EEC on Waste Electrical and Electronic Equipment (WEEE). The Directive
specifies aâframework for the return and recycling of waste appliances and is valid
throughout Europe.

Scope of delivery according to model

Humidity in the drum is caused
byâthe final inspection.
Depending on the connection
Aâ2440 mm dia. hose clip may also be required for connecting the siphon (available from
specialist retailers). aPageâ4: Water connection
Useful tool
Spirit level for aligning the washer dryer.
Wrench for adjusting the machine feet.
Water drainage
Power cord
Water supply
Covers
Hose holder
Aqua-Stop Aqua-Secure Standard
2

Installation area

Stability is important to prevent the machine from wandering.
The installation area must be firm and level.
Soft floors/floor coverings are not suitable.
Ensure the area is well ventilated to achieve good drying performance.
If installing the appliance on a pedestal
It is essential to secure the washer dryer feet with holding bracketsâ*.
If installing the appliance on a wooden joist floor
If possible, install the washer dryer in a corner.
Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
It is essential to secure the washer dryer feet with holding bracketsâ*.
*âorder no. WMZ 2200, WX 9756

Hose and cable lengths


Connection on left side or Connection on right side
Note: if hose holders are used, the hose lengths may be reduced.
Available from dealer/customer service:
Aqua-Stop extension hoseâ**, approx. 2.50 m.
Longer supply hose, approx. 2.20 m, for standard model.
**âorder no. WMZ 2380, WZ 10130

Built-under/Built-in appliance

Build-under/build-in before connection to the power supply.Installed in between kitchen units (built-under or built-in)
Dimension requirement of kitchen unit:
aâ=â650âmm, bâ=â620âmm, câ=â850âmm
Install washer dryer only under a continuous worktop that
is connected firmly to the adjacent cupboards.
The installation area must be well ventilated, otherwise the
washer dryer will operate below optimum performance.
Dimension of ventilation cross-section:
d x e = 200 mm x 100 mm, f = 365âmm
Distance between wall and machine: 50âmm
~140 cm
~160 cm
~140 cm
~90 cm
~165 cm
~95 cm
max. 100 cm
min. 60 cm
f
e
3

Removing transport bolts

Before using the appliance for the first time, always remove and retain
all 4 transport bolts.
If transporting the appliance subsequently, always re-install the
transport bolts  this prevents damage to the machine. aPageâ6
Retain the screw and sleeve.
1. Take the hoses out of the holder and the elbow.
2. Undo and remove all 4 transport bolts.
3. Take the power cord out of the holders. Remove the sleeves.
4. Insert the covers and lock them in place by pressing on the locking hook. Insert the hose
holders.
5. Fix the hoses in the hose holders.
4

Water connection

Risk of electric shock! Do not immerse the Aqua-Stop safety device in water
(containsâanâelectric valve).
To prevent leakage or water damage, follow the instructions in this chapter.
Attention: operate the washer dryer with cold drinking water only.
Do not connect to the mixer tap of a pressureless hot-water heater.
Do not use a used inlet hose. Only use the inlet hose supplied or one which
was purchased from an authorised specialist dealer.
If in doubt, have the appliance connected by a technician.
Water supply
Water inlet hose:
Attention: do not kink, crush, modify or cut through (strength is no longer guaranteed).
Optimum water pressure in the mains: 1001000 kPa (110 bar)
When the tap is turned on, the water flow is at least 8 l/min.
If the water pressure is higher, install a pressure reducing valve.
Model: Aqua-Stop
Aqua-Secure
Standard
1. Connect the water supply hose to the tap.
Tighten plastic screw fittings by hand only.
2. Carefully turn on the tap and check that the
connection points are not leaking.
Attention: the screw connection is under
water mains pressure.
Water drainage
Water drainage hose:
Attention: do not kink or stretch.
Height difference between installation area and outlet: 60100 cm
Drainage into a sink/bath tub:
Attention: secure the drainage hose to prevent it from slipping out
ofâtheâsink.
Attention: the plug must not be in the plug hole. When the water is being
pumped out of the washer dryer, check that the water drains away quickly
enough. Do not immerse the end of the drainage hose in the water that has
been pumped out. There is a risk that water will be drawn back into the
washer dryer.
Drainage into a siphon:
Attention: secure the connection with a 2440 mm dia. hose clip (available
from a specialist retailer).
Drainage into a plastic pipe with rubber sleeve:
Attention: Secure the drainage hose to prevent it from slipping out
ofâtheâdrain.
3/4

min. 10 mm
max.
9
max.
9
3/4

min 10 mm
5
Manufacturer (see Operating instructions) 0312 / 9000 479252

Alignment

High levels of noise, intense vibrations and wandering may be due to incorrect alignment.
Alignment will be carried out by customer service or authorised technicians, if you want
toâalign the machine by yourself please use a spirit level.
Aligning the washer dryer with a spirit level.
1. Undo the lock nut in a clockwise direction using a wrench.
2. Adjust the height by turning the appliance foot.
All four appliance feet must be placed firmly on the floor.
The washer dryer must not be able to wobble.
Check the alignment of the washer dryer with a spirit level andâ
correct if necessary.
3. Tighten the lock nut against the housing.
Hold the foot in place and make sure that the height is not adjusted.
The lock nuts on all four appliance feet must be screwed tightly against
the housing.

Electrical connection

ʑ
Connect the washer dryer to an alternating current via a correctly installed earthed socket
only.
ʑ
The mains voltage and specifications on the washer dryer must match.
aPageâ6: Technical specifications
ʑ
For information about the connected load and required fuse.
aPageâ6: Technical specifications
ʑ
Ensure that:
the mains plug and socket are compatible,
the cable cross-section is adequate,
the earthing system has been installed correctly.
ʑ
A damaged power cord may be replaced by an electrician only.
A replacement power cord is available from customer service.
ʑ
Do not use multiple plugs/connectors or extension cables.
ʑ
If a residual current operated circuit-breaker is used, use only a type which guarantees
compliance with the currently valid regulations.
ʑ
Mains plug:
do not insert into/pull out of the socket with damp hands.
do not pull the plug out of the socket by pulling on the power cord.
never pull out the plug while the appliance is in operation.

View the manual for the Bosch Logixx 7 WVH28421GB here, for free. This manual comes under the category washing machines and has been rated by 30 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the Bosch Logixx 7 WVH28421GB or do you need help? Ask your question here

Need help?

Do you have a question about the Bosch and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 41
A
AmarSeptember 22, 2020

Just put a wash on and within minutes it’s beeping and lights are flashing on start spin and end button. Model Bosch logixx7

3 comments
E
Emma of manua.lsDecember 25, 2023

When the Bosch Logixx 7 WVH28421GB washing machine starts beeping and the lights are flashing on the start spin and end buttons, you can try the following steps: 1. Check the alignment of the washer dryer. High levels of noise, intense vibrations, and "wandering" may be due to incorrect alignment. You can align the machine yourself using a level. Undo the lock nut in a clockwise direction using a wrench, adjust the height by turning the appliance foot, and make sure all four appliance feet are firmly placed on the floor. Check the alignment with a level and correct if necessary. Tighten the lock nut against the housing. 2. Ensure the electrical connection is correct. Connect the washer dryer to a properly installed grounded socket. Make sure the power voltage and specifications on the washer dryer match. Check that the power plug and socket are compatible, the cable size is sufficient, and the grounding system has been installed correctly. If the power cord is damaged, it should be replaced by an electrician. Do not use multiple plugs/connectors or extension cables. If a residual current device circuit breaker is used, make sure it complies with the regulations.

This answer is automatically generated
L
Lorraine May 9, 2021

Flashing on start spin and end unable to open door.

O
Olive TalbotAugust 16, 2021

Flashing and beeping on spin wont finish cycle door wont open

I
Ivan October 10, 2020

I have set the drying program. Everything started working normally. It came to 17 minutes and the time stood still, the pump and the air inhalation could be heard but the drum did not rotate. It did not show any error but it could not be turned off. I turned it off through the program menu, but after that, whenever I turn on any program, the dryer fan turns on immediately and the power button does not respond. Thank you for your help.

This message has been automatically translated
I
Ivan October 11, 2020

Hello! Which program I choose, the fan starts blowing warm air and runs constantly and the machine cannot be turned off. Could you please help me? Thank you.

This message has been automatically translated
E
Emine Pericie February 16, 2021

I accidentally interrupted the running program and now it won't start again. What can I do to resume the washing process from where it left off? Thank you very much and kind regards, Emine Pericie

This message has been automatically translated
B
BarbaraMay 26, 2023

Obviously my machine doesn’t work with the lights flashing there is a beeping alarm as well could you tell me what’s wrong and can I fix it myself, if I can, how? As you can see, the machine is integrated.

Obviously my machine doesn’t work with the lights flashing there is a beeping alarm as well could you tell me what’s wrong an...
zoom-in
View photo
This message has been automatically translated
M
Monika RotherFebruary 14, 2021

The aqua stop is locked, how can I unlock it?

This message has been automatically translated
I
IanApril 30, 2020

When the dishwasher has finished there are small pieces of food stuck to the back of plates etc in the bottom tier of the dishwasher. I clean out the filter regularly but it doesn't seem to help. I was using eco but now use the auto programme which has improved slightly. Any ideas? There is salt in the machine.

J
Jackie June 14, 2020

I dont have the instrucción book and on the screen It says F-23 dont know how to solve the problem

1 comment
T
T S AujlaJune 26, 2020

How to finish spinning and drain

R
Robert FergusonJuly 7, 2021

Bosch logixx 7 showing the following error code. F18 Can then only be reset by turning off the power at the socket point. Please advise. Kind regards Robert

1 comment
J
JackieAugust 6, 2021

What does F 18 mean?

General
BrandBosch
ModelLogixx 7 WVH28421GB | WVH28421GB
Productwashing machine
EAN4242002709918
LanguageEnglish
FiletypeUser manual (PDF)
Design
Appliance placementFreestanding
Loading typeFront-load
Product colorWhite
Door hingeLeft
Control typeButtons, Rotary
Drum volume57 L
Built-in displayYes
CertificationCE, VDE
Water fillCold
Display type-
Drum materialStainless steel
Tub materialPlastic
Performance
Spin-drying class-
Drying capacity4 kg
Maximum spin speed1400 RPM
Washing capacity7 kg
Cycle time washing418 min
No
AquaStop function-
Delayed start timerYes
Delay start (max)24 h
Anti-Crease functionYes
Adjustable spin speed-
Minimum spin speed400 RPM
Noise level (wash)54 dB
Noise level (spin)73 dB
Foam control systemYes
Load balancing systemYes
Noise level (drying)62 dB
Self-cleaningYes
Hand/wool, Mix, Quick, Delicate/silk
Ergonomics
Cord length2.1 m
Door opening angle165 °
Remaining time indicationYes
LED program stage indicatorYes
BuzzerYes
Child lockYes
Other features
B
Washing classA
Annual energy consumption washing238 kWh
Annual water consumption washing10200 L
Annual water consumption washing & drying11400 L
Annual energy consumption washing & drying1134 kWh
Weight & dimensions
Width600 mm
Depth590 mm
Height842 mm
Weight84000 g
Package weight88000 g
Door opening diameter320 mm
Power
Energy consumption washing per cycle1.19 kWh
Energy consumption washing & drying per cycle5.67 kWh
Water consumption washing & drying per cycle57 L
AC input voltage220 - 240 V
AC input frequency50 Hz
Current10 A
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Bosch Logixx 7 WVH28421GB below.

What temperature should I use for my laundry?

The washing label of your garment shows the recommended washing temperature.

Do I need to use an anti-scaling agent for my washing machine?

It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash.

How do I prevent my washing machine from smelling?

Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash.

What is the weight of the Bosch Logixx 7 WVH28421GB?

The Bosch Logixx 7 WVH28421GB has a weight of 84000 g.

What certifications does the Bosch Logixx 7 WVH28421GB have?

The Bosch Logixx 7 WVH28421GB has the following certifications: CE, VDE.

What is the height of the Bosch Logixx 7 WVH28421GB?

The Bosch Logixx 7 WVH28421GB has a height of 842 mm.

What is the width of the Bosch Logixx 7 WVH28421GB?

The Bosch Logixx 7 WVH28421GB has a width of 600 mm.

What is the depth of the Bosch Logixx 7 WVH28421GB?

The Bosch Logixx 7 WVH28421GB has a depth of 590 mm.

Is the Bosch Logixx 7 WVH28421GB a freestanding washing machine?

Yes, the Bosch Logixx 7 WVH28421GB is a freestanding washing machine. This means that it can be placed anywhere in your home without the need for installation.

Does the Bosch Logixx 7 WVH28421GB have a built-in display?

Yes, the Bosch Logixx 7 WVH28421GB has a built-in display. This allows you to easily see and control the settings and progress of your washing cycle.

What is the maximum spin speed of the Bosch Logixx 7 WVH28421GB?

The maximum spin speed of the Bosch Logixx 7 WVH28421GB is 1400 RPM. This high spin speed helps to remove more water from the clothes, reducing the drying time and potentially saving energy.

What is the energy efficiency class of the Bosch Logixx 7 WVH28421GB?

The energy efficiency class of the Bosch Logixx 7 WVH28421GB is B. While this is not the highest rating available, it is still considered to be relatively efficient and will result in cost savings compared to lower-rated models.

What is the annual water consumption for washing with the Bosch Logixx 7 WVH28421GB?

The annual water consumption for washing with the Bosch Logixx 7 WVH28421GB is 10,200 L. This is a relatively low amount of water compared to other washing machines, making it an eco-friendly choice for water-conscious users.

How do I properly transport the Bosch Logixx 7 WVH28421GB washing machine?

To properly transport the Bosch Logixx 7 WVH28421GB washing machine, follow these steps: 1. Turn off the tap to stop the water supply. 2. Release the water pressure in the supply hose. You can refer to page 8 of the manual for instructions on how to check and clean the filter in the water inlet hose. 3. Drain any residual detergent solution from the machine. You can find instructions on how to drain the pump on page 8 of the manual. 4. Isolate the washer dryer from the power supply by disconnecting it. 5. Remove the hoses connected to the machine. 6. If you are transporting the machine, it is recommended to install transport bolts. Remove the covers and, if necessary, the retainer according to the instructions provided. Insert all 4 sleeves and clamp the power cord into the holders. Insert the screws and tighten them. Remember to remove the transport bolts after transportation. 7. To prevent unused detergent from flowing into the outlet during the next wash, pour 1 litre of water into dispenser II and start the Empty (Drain) or Spin program. These steps will ensure that the Bosch Logixx 7 WVH28421GB washing machine is properly prepared for transportation.

What are the technical specifications of the Bosch Logixx 7 WVH28421GB washing machine?

The Bosch Logixx 7 WVH28421GB washing machine has the following technical specifications: - Installation area: The machine should be installed in a firm and level area with good ventilation for optimal drying performance. Soft floors or floor coverings are not suitable. - Hose and cable lengths: The length of the hoses may vary depending on the connection side. Additional accessories like Aqua-Stop extension hoses or longer supply hoses are available from the dealer or customer service. - Built-under/Built-in appliance: If installing the machine between kitchen units, the dimension requirements of the kitchen unit should be followed. The washer dryer should be installed under a continuous worktop that is firmly connected to the adjacent cupboards. The installation area must be well ventilated to ensure optimal performance. - Technical specifications: For detailed technical specifications, please refer to the manual. Please note that these specifications are specific to the Bosch Logixx 7 WVH28421GB washing machine and may vary for other models.

How do I clean the machine housing, control panel, and detergent drawer of the Bosch Logixx 7 WVH28421GB washing machine?

To clean the machine housing, control panel, and detergent drawer of the Bosch Logixx 7 WVH28421GB washing machine, follow these steps: 1. Machine housing and control panel: - Wipe the machine housing and control panel with a soft, damp cloth. - Avoid using abrasive cloths, scourers, or cleaning agents such as stainless steel cleaners. - Immediately remove any laundry or cleaning agent residues. - Do not clean the appliance with a water jet. 2. Detergent drawer: - Pull out the detergent drawer up to the stop position and press down the latch on the insert. - Remove the drawer completely. - Pull the insert upwards with your finger to remove it. - Clean the detergent dispenser and the insert with water and a brush. - Refit the insert and secure it in place, ensuring that the cylinder fits over the guide pin. - Insert the detergent drawer back into its place. - Leave the detergent drawer open to allow residual water to evaporate. 3. Drum: - After washing, leave the washer dryer door open to allow the drum to dry. For removing rust stains, use a chlorine-free cleaning agent and avoid using steel wool. Remember to follow these cleaning steps regularly to maintain the cleanliness and performance of your Bosch Logixx 7 WVH28421GB washing machine.

How do I descale the Bosch Logixx 7 WVH28421GB washing machine if needed?

To descale the Bosch Logixx 7 WVH28421GB washing machine, follow these steps: 1. Ensure that there is no laundry in the machine. 2. Check if descaling is necessary. If the detergent is dosed correctly, descaling may not be required. 3. If descaling is needed, follow the instructions provided by the descaler manufacturer. 4. Suitable descaling products can be purchased from the Bosch website or after-sales service. 5. Disconnect the mains plug and set the programme selector to Off. 6. Open and remove the service flap. 7. Release the drainage hose from the clip and remove the sealing plug. 8. Allow the detergent solution to flow out and then push the sealing cap back in. 9. Remove the pump cap and clean any foreign objects, loose debris, or fluff from inside the pump. Ensure that the impeller in the pump can rotate freely. 10. Clean any residual lye or fluff from the thread of the pump cap and pump housing. 11. Attach the pump cap tightly until it stops, with the handle upright. 12. Place the drainage hose back in the retainer. 13. Close the service flap. Following these steps will help you descale the Bosch Logixx 7 WVH28421GB washing machine effectively.

What should I do if I encounter a fault with the Bosch Logixx 7 WVH28421GB washing machine?

If you encounter a fault with the Bosch Logixx 7 WVH28421GB washing machine, follow these steps: 1. Check the alignment: High levels of noise, intense vibrations, or "wandering" may be due to incorrect alignment. Use a spirit level to align the machine. Adjust the height of the appliance feet and ensure all four feet are firmly placed on the floor. 2. Electrical connection: Ensure that the washer dryer is connected to a correctly installed earthed socket. Check that the mains voltage and specifications match. Avoid using multiple plugs, connectors, or extension cables. If the power cord is damaged, it should be replaced by an electrician. 3. Removing transport bolts: Before using the appliance for the first time, remove and retain all four transport bolts. If transporting the appliance subsequently, re-install the transport bolts to prevent damage. 4. Water connection: Connect the water supply hose to the tap, ensuring it is not kinked or crushed. Check for leaks at the connection points. Use cold drinking water only and avoid connecting to a pressureless hot-water heater. 5. Water drainage: Ensure the water drainage hose is not kinked or stretched. If draining into a sink or bath tub, secure the hose to prevent slipping. If draining into a siphon or plastic pipe, use appropriate connections and secure them properly. If the fault persists or you require further assistance, contact customer service or an authorized technician for support.

Is the manual of the Bosch Logixx 7 WVH28421GB available in English?

Yes, the manual of the Bosch Logixx 7 WVH28421GB is available in English .

Is your question not listed? Ask your question here

No results