Bosch GSB 13 RE Professional manual

Bosch GSB 13 RE Professional
8.6 · 12
PDF manual
 · 71 pages
English
manualBosch GSB 13 RE Professional
36 | 中文
冲击钻
GSB ... 10 10 RE 13 13 RE 16 16 RE
毫米 8 8 10 10 12 12
木材
毫米 20 20 25 25 30 30
夹头的夹紧范围
毫米 1.5–10 1.5–10 1.5–13 1.5–13 1.5–13 1.5–13
重量符合EPTA-Procedure
01:2014
千克 1.5 1.5 1.8 1.8 1.9 1.9
保护等级
/ II / II / II / II / II / II
所有参数适用于230伏的额定电压[U],对于其他不同的电压和国际规格,数据有可能不同。
安装
u 在电动工具上进行所有操作之前都必须从插座上
拔出电源插头。

辅助手柄(见图片A)

u 操作电动工具时务必使用辅助手柄(11)
u 在所有操作前确认翼形螺栓已拧紧。失控可能会
造成人身伤害。
可以任意翻动辅助手柄(11),以便在工作时毫无疲
劳地牢牢抓紧。
逆时针旋转辅助手柄调节翼形螺栓(10),并将辅助
手柄(11)转到需要的位置。然后再次顺时针拧紧翼
形螺栓(10)
调整钻孔深度(参见插图A)
利用限深器(12)可以确定所需的钻深X
按压限深器调节键(9),并将限深器装入辅助手柄
(11)
限深器(12)的槽纹必须朝下。
尽可能地拉出限深器(12),使钻尖与限深器(12)
端之间的距离等于所需的钻孔深度X
更换刀具
u 更换刀具时,请佩戴保护手套。长时间工作之后
夹头会变得十分炽热。
快速夹头(见插图B)
电源开关(6)未按下时可锁定钻轴。这样就能快速便
捷地更换钻夹头中的工具刀头。
沿着方向转动,打开快速夹头(1),直至可以插入
刀具。安装好刀具。
沿着旋转方向用手使劲转动快速夹头(1)的衬套,
直至不再听到过于卡紧的声音为止。由此钻夹头会
被自动锁止。
反向转动前套筒来移除刀具时,锁止件再次自动松
开。
齿环夹头(参见插图C)
旋转打开齿环夹头(15),直至可以装入刀具。安装
好工具。
将夹头扳手(14)插入齿环夹头(15)相应的孔中,然
后均匀拧紧工具。
起子机的工具(见插图D)
使用螺丝批嘴(17)时,应当使用通用批嘴架(16)
必须使用与螺丝头大小相符的螺丝批嘴。
旋螺栓时,应将“钻孔/冲击钻”(4)转换按钮调
到“钻孔”图标上。

更换钻夹头

u 在电动工具上进行所有操作之前都必须从插座上
拔出电源插头。
拆卸钻夹头(见图片E)
为了拆卸快速夹头(1),将内六角扳手(18)夹到快速
夹头(1)中并将开口扳手(19)(SW 12)放在驱动轴
的扳手着力面上。
将电动工具放到一个稳固的底板上,例如工作台。
固定开口扳手(19),朝方向转动六内角扳手(18)
松开快速夹头(1)。通过轻轻敲击内六角扳手(18)
长柄来松开卡住的快速夹头。
将内六角扳手从快速夹头中拆下,然后完全拧下快
速夹头。
请按照与拆卸快速夹头相同的方式拆卸齿环夹头
(15)
安装钻夹头(参见插图F)
以相反的顺序安装快速夹头。
必须以30–35牛米的拧紧力矩拧紧钻夹头。

抽吸粉尘/切屑

含铅的颜料以及某些木材、矿物和金属的加工废尘
有害健康。机器操作者或者工地附近的人如果接
触、吸入这些废尘,可能会有过敏反应或者感染呼
吸道疾病。
某些尘埃(例如加工橡木或山毛榉的废尘)可能致
癌,特别是和处理木材的添加剂(例如木材的防腐
剂等)结合之后。只有经过专业训练的人才能够加
工含石棉的物料。
工作场所要保持空气流通。
最好佩戴P2滤网等级的口罩。
请留心并遵守贵国和加工物料有关的法规。
u 避免让工作场所堆积过多的尘垢。尘埃容易被点
燃。
运行
投入使用
u 注意电源电压!电源的电压必须和电动工具铭牌
上标示的电压一致。标记为230伏电动工具用220
伏的电压可以驱动。
1 609 92A 5BU | (06.11.2020) Bosch Power Tools

View the manual for the Bosch GSB 13 RE Professional here, for free. This manual comes under the category drill machines and has been rated by 12 people with an average of a 8.6. This manual is available in the following languages: English. Do you have a question about the Bosch GSB 13 RE Professional or do you need help? Ask your question here

Need help?

Do you have a question about the Bosch and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 5
J
Juan Manuel MassiniJuly 11, 2021

Hello, the button that changes the direction of the drill is stuck and the drill is stuck in reverse. I don't know how to fix it.

Hello, the button that changes the direction of the drill is stuck and the drill is stuck in reverse. I don't know how to fix...
zoom-in
View photo
This message has been automatically translated
K
KatiDecember 26, 2017

Hello, something curious happened to us, we cannot remove the drill bit in any way. Has this happened to anyone else? Do you know how to remove it if it gets stuck? Thank you.

This message has been automatically translated
B
brianDecember 7, 2023

THE DRILL BIT IN MY BOSCH GSB 13 RE DRILL KEEPS LOOSENING ITSELF?

T
TGMarch 23, 2015

Do you have the bosch gsb 13 re switch manual?I want to repair the switch,because some part on the switch was broken.tq

P
Philip Peter WilsonMarch 15, 2024

changing motor brushes

The Bosch GSB 13 RE Professional is a drill machine designed for professionals in various industries. With its keyless chuck type, it offers convenience in changing drill bits. The drill machine has a maximum torque of 10.8 N⋅m, allowing for efficient drilling in different materials. Operating at a maximum idle speed of 2800 RPM, the drill machine can quickly and precisely penetrate surfaces. It also features adjustable speed settings, enabling users to adapt to different drilling requirements. The tool offers a reverse function, allowing users to remove screws or back out drill bits effortlessly. The Bosch GSB 13 RE Professional is equipped for hammer drilling, with an impact rate of 44800 bpm. This feature makes it suitable for both drilling and chiseling tasks in materials such as concrete. The drill machine has a maximum drilling diameter of 10 mm in steel, 13 mm in concrete, and 25 mm in wood, providing versatility for various applications. Designed with a soft grip handle, the drill machine ensures comfort and improved handling during prolonged use. Weighing 1800 g, it offers a balanced and manageable weight, reducing user fatigue. The Bosch GSB 13 RE Professional operates using an AC power source, providing a consistent and reliable power supply for uninterrupted work. With an output power of 301 W and an input power of 600 W, it delivers sufficient power for demanding drilling tasks. Crafted with the renowned Bosch quality, the GSB 13 RE Professional guarantees durability and longevity. Its sturdy construction and premium materials ensure that it can withstand challenging work environments. In conclusion, the Bosch GSB 13 RE Professional is a versatile and powerful drill machine that offers convenience, durability, and efficiency in various drilling applications.

General
BrandBosch
ModelGSB 13 RE Professional | 0 601 217 100
Productdrill machine
EAN3165140371902
LanguageEnglish
FiletypeUser manual (PDF)
Features
Chuck typeKeyless
Adjustable speedYes
ReverseYes
Hammer drillingYes
Soft gripYes
Performance
Torque (max)10.8 N⋅m
Idle speed (max)2800 RPM
Impact rate (high speed)44800 bpm
Drilling diameter in steel (max)10 mm
Drilling diameter in concrete (max)13 mm
Drilling diameter in wood (max)25 mm
Power
Output power301 W
Input power600 W
Power sourceAC
AC input voltage230 V
Weight & dimensions
Weight1800 g
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Bosch GSB 13 RE Professional below.

How do I remove rust from my Bosch drill machine?

1. Soak the rusty part in vinegar until completely soaked through. 2. Let the vinegar work on the rust for 24 hours. 3. Remove the rust with a wire brush or aluminium foil.

What does '16V' or '20V' mean?

The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.

Do I have to wear hearing protection when using a drill machine?

The amount of sound varies a lot per brand and type of drill machine, it is therefore wise to wear hearing protection to be sure.

What is the weight of the Bosch GSB 13 RE Professional?

The Bosch GSB 13 RE Professional has a weight of 1800 g.

How do I adjust the speed of the Bosch GSB 13 RE Professional drill machine?

The speed adjustment on the Bosch GSB 13 RE Professional is conveniently located near the trigger. Simply turn the speed control dial to increase or decrease the drilling speed according to your requirements.

How do I change the drill bit on the Bosch GSB 13 RE Professional?

Changing the drill bit on the Bosch GSB 13 RE Professional is a breeze. First, ensure the drill is switched off and unplugged. Then, using the chuck key provided, insert it into the chuck and turn it counterclockwise to loosen the jaws. Remove the previous drill bit and insert the new one, making sure it is securely in place. Finally, tighten the chuck by turning the chuck key clockwise until the drill bit is firmly held.

What is the maximum drilling capacity of the Bosch GSB 13 RE Professional?

The Bosch GSB 13 RE Professional has a maximum drilling capacity of 13 millimeters in concrete, 10 millimeters in steel, and 25 millimeters in wood. Ensure you select the appropriate drill bit and adjust the drilling speed accordingly for optimal results.

How do I switch the Bosch GSB 13 RE Professional from drilling to hammer drilling mode?

Switching between drilling and hammer drilling modes on the Bosch GSB 13 RE Professional is a simple process. Use the mode selector switch located on the top of the tool to choose between the different modes. For drilling, set the switch to the drill symbol, and for hammer drilling, set it to the hammer symbol. Always ensure the tool is switched off before changing the mode.

How do I operate the depth stop feature on the Bosch GSB 13 RE Professional?

The depth stop feature on the Bosch GSB 13 RE Professional allows you to control the drilling depth precisely. To use it, first, loosen the depth stop control ring located above the chuck. Then, adjust the desired drilling depth by moving the depth stop rod up or down. Once you have set the desired depth, tighten the control ring to secure the depth stop in place. This feature ensures consistent drilling depth for repeated tasks.

Does the Bosch GSB 13 RE Professional have a keyless chuck?

Yes, the Bosch GSB 13 RE Professional has a keyless chuck. This allows for quick and easy bit changes without the need for a key.

What is the maximum torque of the Bosch GSB 13 RE Professional?

The maximum torque of the Bosch GSB 13 RE Professional is 10.8 N⋅m. This means it can deliver a high level of force to drive screws and drill into tough materials.

Can the Bosch GSB 13 RE Professional's speed be adjusted?

Yes, the Bosch GSB 13 RE Professional has adjustable speed. This allows users to customize the drilling or driving speed to fit the task at hand.

Does the Bosch GSB 13 RE Professional have a reverse function?

Yes, the Bosch GSB 13 RE Professional has a reverse function. This enables users to easily remove screws or back out of holes without needing to manually turn the tool.

What is the maximum drilling diameter in concrete for the Bosch GSB 13 RE Professional?

The maximum drilling diameter in concrete for the Bosch GSB 13 RE Professional is 13 mm. This indicates that it is suited for drilling small to medium-sized holes in concrete surfaces.

Is the manual of the Bosch GSB 13 RE Professional available in English?

Yes, the manual of the Bosch GSB 13 RE Professional is available in English .

Is your question not listed? Ask your question here

No results