View the manual for the Bosch GCM 8 SJL here, for free. This manual comes under the category saws and has been rated by 13 people with an average of a 7.4. This manual is available in the following languages: English. Do you have a question about the Bosch GCM 8 SJL or do you need help? Ask your question here




The Bosch GCM 8 SJL is a saw with a blade diameter of 216 mm and a blade bore of 30 mm. It operates at an idle speed of up to 5500 RPM, making it capable of delivering efficient and precise cutting performance. With an input power of 1600 W, this saw provides the necessary strength to tackle various cutting tasks. In terms of its physical characteristics, the Bosch GCM 8 SJL weighs 17300 g, which may be considered relatively heavy compared to other saws on the market. It has dimensions of 910 mm in depth, 410 mm in height, and 460 mm in width, allowing for easy maneuverability and storage. The saw comes with a saw blade included, ensuring that the user has the appropriate blade for immediate use. This feature adds convenience and eliminates the need for separate purchases. When it comes to vibration emission, the Bosch GCM 8 SJL produces 2.5 m/s², which is within acceptable limits for most users. However, it is important to note that there is an uncertainty K factor of 1.5 m/s², which should be considered for more accurate assessments of vibration levels. Overall, the Bosch GCM 8 SJL provides a powerful cutting experience with its high idle speed, sturdy construction, and included saw blade. Its weight and dimensions may require some adjustment during operation, but its performance and reliability make it a suitable tool for various cutting applications.
| Brand | Bosch |
| Model | GCM 8 SJL | 0 615 990 FZ5 |
| Product | saw |
| EAN | 3165140654319 |
| Language | English |
| Filetype | User manual (PDF) |
| Idle speed (max) | 5500 RPM |
| Blade diameter | 216 mm |
| Blade bore | 30 mm |
| Cutting depth (90º) | - mm |
| Idle speed (max) | 5500 RPM |
| Compound cut capacity (45° x 45°) | 70 x 214 mm |
| Saw blade included | Yes |
| Saw blade included | Yes |
| Blade diameter | 216 mm |
| Input power | 1600 W |
| Input power | 1600 W |
| Power source | AC |
| Weight | 17300 g |
| Depth | 910 mm |
| Height | 410 mm |
| Width | 460 mm |
| Weight | 17300 g |
| Depth | 910 mm |
| Height | 410 mm |
| Width | 460 mm |
| Miter cut | 51 - 60 ° |
| Cross stop tilt angle range | 47 - 2 ° |
| Diamond disc | - |
| Vibration emission | 2.5 m/s² |
| Uncertainty K | 1.5 m/s² |
| Cutting width 45° x 45° | 70 x 214 mm |
| Dust extraction port | Yes |
| Dust extraction | Yes |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Bosch GCM 8 SJL below.
The Bosch GCM 8 SJL has a weight of 17300 g.
1. Wipe sawdust from the saw blade with a brush. 2. Spray the saw blade with oven cleaner and leave for 30 minutes. 3. Remove the oven cleaner and dirt with a dry cloth. 4. Grease saw blade with Vaseline.
If there is resin or other debris on the blade, it may look like the blade is blunt. If the saw blade has been thoroughly cleaned and is still blunt, it is recommended to have the saw blade sharpened.
1. Soak the rusty part in vinegar until completely soaked through. 2. Let the vinegar work on the rust for 24 hours. 3. Remove the rust with a wire brush or aluminium foil.
The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.
The amount of sound varies a lot per brand and type of saw, it is therefore wise to wear hearing protection to be sure.
The Bosch GCM 8 SJL has a height of 410 mm.
The Bosch GCM 8 SJL has a width of 460 mm.
The Bosch GCM 8 SJL has a depth of 910 mm.
Make sure the saw is properly plugged into a working power outlet and the power switch is turned on. Check if the power cord is not damaged. Also, ensure that the saw's safety features, such as the handle lock or trigger lock, are properly engaged or disengaged.
Ensure the blade is securely tightened onto the arbor and that it is sharp and not dull or damaged. Check if the material being cut is properly supported and stable. Also, verify if the saw's bevel and miter adjustments are properly set for the desired cut.
Locate the bevel adjustment knob or lever, usually located near the front of the saw's turntable. Loosen the knob or unlock the lever, adjust the desired bevel angle, and then tighten the knob or lock the lever again to secure the setting.
Check the alignment of the fence or guide system being used, ensuring it is properly adjusted and parallel to the blade. If necessary, refer to the saw's user manual for instructions on how to adjust the fence or guide system for accurate alignment.
Unplug the saw and ensure the blade guard is fully retracted. Loosen the arbor nut or bolt holding the blade in place, usually by turning it counterclockwise. Remove the old blade and replace it with a new one, ensuring the teeth are facing in the correct direction for the desired cut. Tighten the arbor nut or bolt securely, following the manufacturer's instructions for proper torque.
Yes, the Bosch GCM 8 SJL has an idle speed of 5500 RPM. This means that it can cut through materials quickly and efficiently.
Yes, the Bosch GCM 8 SJL comes with a saw blade included. This saves the user the hassle of purchasing a separate blade.
The blade diameter of the Bosch GCM 8 SJL is 216 mm. This size is suitable for cutting through a variety of materials.
The blade bore of the Bosch GCM 8 SJL is 30 mm. This means that it is compatible with a wide range of saw blades.
The input power of the Bosch GCM 8 SJL is 1600 W. This high power rating ensures that the saw has sufficient power to tackle demanding cutting tasks.
Yes, the manual of the Bosch GCM 8 SJL is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Bosch and is the answer not in the manual?
Question and answer
Number of questions: 2How do I adjust the laser when the blade and laser are not in agreement?
This message has been automatically translatedHow do I change the UV bulb. Mine stopped working after a few minutes