Bosch EcoLogixx 7S WTW8656ECO manual

Bosch EcoLogixx 7S WTW8656ECO
8.7 · 152
PDF manual
 · 10 pages
English
manualBosch EcoLogixx 7S WTW8656ECO
8

Installation

– Scope of delivery: dryer, installation and instruction manual, basket for woollens (depending on the model).– Check dryer for transport damage.– The dryer is very heavy. Do not lift without assistance.– Be careful to avoid sharp edges.– Do not install in a room which is susceptible to frost. Water may cause damage once it starts to freeze.– If in doubt, have the appliance connected by a specialist.– Do not lift the dryer by any of the protruding parts (e.g. the door) as they may break off.Setting up the dryer– The appliance plug must always be accessible.– Ensure that the appliance is installed on a clean, level and firm surface.– Do not obstruct the air inlet on the front of the dryer.– Keep the area around the dryer clean.– Level the dryer using the threaded feet.Use a spirit level.– Do not remove the threaded feet under any circumstances.Mains connection see safety information a Page 13.– Connect to an AC earthed socket. If in doubt, have the socket checked by a specialist.
The mains voltage and the voltage shown on the rating plate (a Page 10) must be the
same.– The connected load and necessary fuse protection are specified on the rating plate.

Frost protection

Preparation1. Empty the condensate container a page 4.2. Select any programme using the programme selector.
3. Press the Start/Stop button a condensation is pumped into the container.
4. Wait 5 minutes and then empty the condensate container again.5. Turn the programme selector to Off.

Transport

– Preparation of dryer a see Frost protection.– Transport the dryer in a vertical upright position.– Following transportation, leave the dryer to stand for two hours.There may be residual water in the dryer.This can leak out if the dryer is at an angle.
1.
Remove all accessories from the drum.The drum must be empty.Make sure that the air inlet remains unobstructedClean and levelDo not install the dryer behind a door or sliding door, which could prevent or restrict opening of the dryer door. This will prevent children from locking themselves in and putting their lives in danger.
2.
Do not operate the dryer i
f
there is a danger of frost.
9
Only when the appliance is switched off.

Care and cleaning

Heat exchangerThe heat exchanger of the dryer is cleaned automatically when drying is in progress, Clnappears in the display panel. Do not pull the condensate container out during the cleaning process.Dryer housing, control panel, air intakeWipe with a soft, damp cloth.Do not use harsh cleaning agents or solvents.Remove detergent and cleaning agent residue immediately.Water may occasionally accumulate between the window and the seal. This does not impair the functions of your dryer in any way.Filter in the condensation tankThe filter is cleaned automatically when the condensate container is emptied. However, the filter should still be cleaned regularly under running water. This prevents stubborn deposits/dirt from building up.
Cleaning is only required if the symbol ā flashes again in the display panel after the condensate
container has been emptied.1. Pull out the condensate container.2. Pull the filter out of its snap-in lock.3. Clean the filter under running water or in the dishwasher.4. Refit the filter.5. Insert the condensate container so that it locks into place.Only operate the dryer with the filter inserted.Moisture sensorThe dryer is equipped with stainless-steel moisture sensors. These measure how damp the laundry is. After long periods of use, a fine layer of limescale can form on the moisture sensors.1. Open the door.2. Clean the moisture sensors using a damp sponge with a rough surface.Do not use steel wool or other abrasive materials.
10

Technical data

ʠ
Dimensions (DxWxH) 60 x 60 x 85 cm (height adjustable)Weight approximately 53 kgMax. capacity 7 kgCondensate container 4.0 lConnection voltage 220-240 VConnected load max. 800 WFuse protection 10 AAmbient temperature 5 - 35°CProduct numberProduction numberunder the doorThe rating plate can be found on the back of the dryer.
ʠ
Drum interior light (depending on model): The drum lights up after the door is opened
and after the programme starts, and switches off automatically.

Consumption rates

Fabrics/programmesResidual moisture in the fabrics after spinningDrying time**Energyconsumption**LüCottons 7 kgCupboard Dry* 1400 rpm(50%) 151 min 1.33 kWh1000 rpm(60%) 178 min 1.65 kWh800 rpm(70%) 205 min 1.92 kWhIron Dry* 1400 rpm(50%) 110 min 0.94 kWh1000 rpm(60%) 137 min 1.24 kWh800 rpm(70%) 166 min 1.55 kWhEasy-Care 3.5 kgCupboard Dry* 800 rpm(40%) 64 min 0.54 kWh600 rpm(50%) 81 min 0.68 kWh* Programme setting for testing in accordance with applicable standard EN61121.
** The values may differ from those specified, depending on the type of fabric, composition of
laundry to be dried, residual moisture in the fabric and the amount of laundry being loaded.Fabrics/programmes Drying time Annual energy consumption
LüCottons 7 kg / 3.5ükg*
Cupboard Dry*** 139 min / cycle212ükWh / year
***Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU.

Optional accessories(from after-sales service using order number, depending on model)

Washer-dryer stack connection setThe dryer can be placed on top of a suitable washing machine with the same width and depth
to save space. The dryer must be fastened to the washing machine using this connection set.
WTZ 11400: with pull-out worktop.Installation underneath the worktopInstead of the appliance covering plate, you must have a metal cover fitted by a specialist.PlatformFor easier loading and unloading. The basket contained in the drawer can be used to carry the laundry.
WTZ
20410
WTZ
10290
WMZ
20500
11

Normal noises

During drying, the compressor and the pump generate some noise which is entirely normal.The compressor in the dryer may occasionally generate a droning noise. The volume and pitch of this may varydepending on the selected programmes and the progress of the drying.The compressor in the dryer is ventilated from time to time, which creates a whirring sound.The automatic cleaning process causes a clicking noise.The process of pumping the condensation into the condensate container generates pumping noises.
12

What to do if ...

If you cannot rectify a fault yourself (e.g. switching off/on), please contact our after-sales service. We will always find an appropriate solution and will avoid unnecessary visits by engineers. Trust the expertise of the manufacturer and rest assured that the repair will be carried out by trained
service technicians using original spare parts. The contact details of your local after-sales service
can be found in the enclosed after-sales service directory, or by calling one of these numbers:
GB 0844 8928979 (Calls from a BT landline will be charged at up to 3 pence per minute. A call
set-up fee of up to 6 pence may apply.)
IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.)
When contacting the after-sales service, please quote the appliance's product number (E no.) and production number (FD) (see the inside of the door).Set the programme selector to Off and remove the appliance plug from the socket.
ʠ
The Start/Stop indicator lamp does not light up.Mains plug plugged in?Programme selected?Check the socket fuse.
ʠ
The display panel light and indicator lights (depending on model) go out and the Start/Stop indicator light flashes.Energy-saving mode is activated a see the separate Energy-saving mode instructions.
ʠ
The ā symbol and Start/Stopindicator lamp flash.Empty container for condensation a see page 4.Clean the condensate container filter if necessary a Page 9.Each time the dryer is transported, you must wait two hours before operating it.
ʠ
The 4 symbol and Start/Stopindicator lamp flash.Rinse the fluff filter under running water a Page 4.
ʠ
Dryer does not start. Start/Stop button selected?
Door closed?Programme set?Ambient temperature greater than 5 °C?
ʠ
Water is leaking out. Make sure the dryer is level.
ʠ
The door opens by itself. Push the door closed until you hear it click into place.
ʠ
Creasing. Laundry load exceeded?Remove articles of clothing immediately after the end of the programme, hang up and pull into shape.Unsuitable programme selected a Page 7.
ʠ
Drying result is not satisfactory (laundry feels too damp).Warm laundry feels damper than it actually is.The selected programme does not suit the load. Use another drying programme or, in addition, select the time programme a Page 7.Use fine adjustment for the drying result a Page 1/2.Fine layer of limescale on the humidity sensors a Clean the humidity sensors a Page 9.Programme termination, e.g. tank full, mains power supply failure, door open or maximum drying time reached.
ʠ
Drying time too long. Rinse the fluff filters under running water a Page 4.
Insufficient supply of air a ensure that air can circulate.
Air inlet possibly blocked a Clear inlet a Page 8.
Ambient temperature higher than 35 °C a ventilate the room.
ʠ
The humidity in the room increases significantly.Make sure the room is sufficiently ventilated.
ʠ
Cln appears in the display panel. Not an error! Automatic cleaning of the heat exchanger.
Do not empty the condensate container.
ʠ
Power cut. Remove the laundry from the dryer immediately and spread it out. Heat may escape. Be careful as the door, the drum and the laundry may be hot.
ʠ
Other intermittent noises and vibrations.Not an error!Normal noises a Page 11.
ʠ
Loud humming noise for several seconds.Has the condensate container been properly reinserted? a Push the condensate container all the way in.Not an error! Normal noises a Page 11.
13

Safety instructions

Emergency– Pull the appliance plug out of the socket immediately or disconnect the fuse.ONLY use the dryer...– in rooms inside the house.– to dry fabrics. The dryer must NEVER...– be used for purposes other than those described above.– be modified in terms of its technology or properties.Hazards– The dryer must not be used by children or persons who have not been instructed in its use.– Do not leave children unsupervised near the dryer.– Keep pets away from the dryer.– Remove all objects from the pockets of garments.Pay particular attention to cigarette lighters a Risk of explosion– Do not lean or sit on the door a Risk of tipping.Installation– Secure loose cables a Tripping hazard.– Do not operate the dryer where there is a risk of frost.Mainsconnection– Connect the dryer according to specifications to an AC earthed socket, otherwise it cannot be guaranteed that the appliance is completely safe.– The cable cross-section must be sufficient.– Only use earth-leakage circuit breakers with the following symbol: – The appliance plug and socket must be compatible.– Do not use multiple plugs/connectors and/or extension cables. – Do not touch or hold the appliance plug with wet hands a Risk of electric shock.– Never pull the appliance plug out of the socket by its cable.– Do not damage the mains lead a Risk of electric shock.Operation– Only laundry must be loaded into the drum.Before switching on the dryer - check the contents.– Do not use the dryer if the laundry has been in contact with solvents, oil, wax, grease or paint (e.g. hair setting spray, nail polish remover, stain remover, cleaning solvent, etc.) a Fire/explosion hazard.– Hazard caused by dust (e.g. coal dust, flour): do not use the dryera Risk of explosion!– Do not turn off the dryer until the drying process ends, unless the laundry will be removed quickly and spread out, so that the heat can dissipate.
Do not put laundry containing foamed material/rubber in the dryer a elastic
material may be destroyed and the dryer may be damaged due to possible deformation of the foamed material.– Light things, such as long hair, may be sucked into the air inlet of the dryer aRisk of injury.– Switch off the dryer once the programme has ended.– The water from condensation is not drinking water and may be contaminated with fluff.Defect– Do not use the dryer if it is defective or if you suspect that it is.Repairs must only be carried out by the after-sales service.– Do not use a dryer with a faulty mains lead. To prevent risks, a faulty mains lead must only be replaced by the after-sales service.Spare parts– Only use genuine spare parts and accessories for safety reasons.Disposal
Dryer: unplug the appliance plug, then cut the mains lead from the appliance.
Dispose of the dryer at an approved public disposal facility.– The heat exchanger contains fluorinated greenhouse gas R134a covered by the Kyoto Protocol a dispose of in a proper manner. Capacity: 0.22 kg.– Packaging: keep all packaging out of reach of babies and children. a Danger of suffocation!– All materials are environmentally safe and recyclable. Dispose of in an environmentally-responsible manner.
Dryer
en Instruction manual

View the manual for the Bosch EcoLogixx 7S WTW8656ECO here, for free. This manual comes under the category dryers and has been rated by 152 people with an average of a 8.7. This manual is available in the following languages: English. Do you have a question about the Bosch EcoLogixx 7S WTW8656ECO or do you need help? Ask your question here

Need help?

Do you have a question about the Bosch and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 20
S
Sajid El mariniFebruary 5, 2023

Hello, the dryer will stop rotating after a minute when I turn it on. I see a symbol, but I don't know what it means.

Hello, the dryer will stop rotating after a minute when I turn it on. I see a symbol, but I don't know what it means.
zoom-in
View photo
This message has been automatically translated
S
SimonaNovember 3, 2022

Hello! I would like to know why the Bosch EcoLogixx 7S WTW8656ECO dryer stops. The indicator above '1' appears and it stops.

Hello! I would like to know why the Bosch EcoLogixx 7S WTW8656ECO dryer stops. The indicator above '1' appears and it stops.
zoom-in
View photo
This message has been automatically translated
S
Strobel Michael October 14, 2022

The dryer stops and the Start/Stop light blinks. This problem occurs with all programs. The water tank is not full. Thank you in advance.

The dryer stops and the Start/Stop light blinks. This problem occurs with all programs. The water tank is not full. Thank you...
zoom-in
View photo
This message has been automatically translated
A
Anna parrellaFebruary 17, 2021

After starting the dryer, it stops after a few minutes and a small window appears on the display. What can I do?

This message has been automatically translated
I
IdaOctober 24, 2020

Hello, I have a Bosch EcoLogixx 7S WTW8656ECO dryer. I started a cycle and accidentally stopped it. I tried to restart it but it won't start again, and the start button is flashing. What should I do, please?

This message has been automatically translated
W
William LeinhosDecember 18, 2016

Hello, on our Ecologixx 7 S there has been a symbol visible recently, all the way to the right, which looks like a full bucket. Water cartridge is empty, lint filter as well. What now?

This message has been automatically translated
A
ahmetDecember 12, 2019

Dear, I am wondering if you have a user manual for the Bosch EcoLogixx 7S WTW8656ECO dryer. I would be very grateful if you could send it to my email address ahmetbesirovic@yahoo.com. Sincerely, Ahmet

This message has been automatically translated
M
Martha HansenFebruary 3, 2019

When I want to start the dryer, a "key" appears on the display along with a beep and then I cannot start the dryer. It seems like something is locked. Can you help me?

This message has been automatically translated
B
Barbara MierzwaOctober 30, 2017

As previously described by some people: the dryer starts and stops after a few minutes - a symbol of a container filled with liquid appears, but emptying the water container or cleaning the fine mesh or two lint filters does not help ... what to do?

This message has been automatically translated
T
tjodroeJanuary 24, 2017

The same problem as described several times by others: "I start the dryer, it starts. After about 8 turns, it stops, beeps, and a symbol appears on the display that looks like a measuring cup almost full. Condensation water and lint filter are cleaned and emptied." What is the solution?

This message has been automatically translated

General
BrandBosch
ModelEcoLogixx 7S WTW8656ECO | WTW8656ECO
Productdryer
EAN4242002798561
LanguageEnglish
FiletypeUser manual (PDF)
Design
Appliance placementFreestanding
Loading typeFront-load
Drying systemCondensation
Product colorWhite
Door hingeRight
Control typeButtons, Rotary, Touch
Drum volume112 L
Built-in displayYes
Display typeLCD
Cord length1.45 m
Door opening angle180 °
CertificationCE, VDE
Performance
Drum capacity7 kg
Drying classA
Cycle time178 min
Noise level65 dB
Anti-Crease functionYes
Anti-Crease cycle120 min
Wool, Mix, Sport, Timed, Blouse/shirt, Cotton
Ergonomics
Delayed start timerYes
Delay start (max)24 h
Drum interior lightYes
LED program stage indicatorYes
Child lockYes
Self-cleaningYes
Power
Energy efficiency classA++
Connected load100 W
AC input voltage220-240 V
AC input frequency50 Hz
Power consumption (off)0.1 W
Energy consumption1.65 kWh
Annual energy consumption212 kWh
Current10 A
Weight & dimensions
Width598 mm
Depth636 mm
Height842 mm
Weight53000 g
Depth with door open1060 mm
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Bosch EcoLogixx 7S WTW8656ECO below.

What is a condenser dryer?

A condenser dryer is a dryer in which condensation ends up in a reservoir.

What is a drain dryer?

A drain dryer is a dryer in which the warm air and condensation are drained through a hose.

What is the best thing to do about a smelly dryer?

It is best to wipe the dryer drum with a damp cloth and some lemon cleaner.

There is a burning smell from my dryer, now what?

Check the following: - That the fluff filter is clean. - That the bottom of the dryer is free of dust. - That the drain hose is clean. If the above does not help, a mechanic should be called in.

What is the weight of the Bosch EcoLogixx 7S WTW8656ECO?

The Bosch EcoLogixx 7S WTW8656ECO has a weight of 53000 g.

What certifications does the Bosch EcoLogixx 7S WTW8656ECO have?

The Bosch EcoLogixx 7S WTW8656ECO has the following certifications: CE, VDE.

What is the height of the Bosch EcoLogixx 7S WTW8656ECO?

The Bosch EcoLogixx 7S WTW8656ECO has a height of 842 mm.

What is the width of the Bosch EcoLogixx 7S WTW8656ECO?

The Bosch EcoLogixx 7S WTW8656ECO has a width of 598 mm.

What is the depth of the Bosch EcoLogixx 7S WTW8656ECO?

The Bosch EcoLogixx 7S WTW8656ECO has a depth of 636 mm.

What energy label does the Bosch EcoLogixx 7S WTW8656ECO have?

The Bosch EcoLogixx 7S WTW8656ECO has energy label A++.

Why is my Bosch EcoLogixx 7S dryer not starting?

Check if the power cord is securely plugged into the electrical outlet. Additionally, make sure the door is properly closed and latched as the dryer won't start unless the door is fully closed.

How can I select the desired drying program on my Bosch EcoLogixx 7S dryer?

Turn the program selection dial to the desired program. Make sure to consult the control panel diagram in the manual to select the appropriate drying program based on your specific needs.

Why is my laundry taking longer to dry than usual in my Bosch dryer?

Ensure that the lint filter is clean and free from any lint or debris. Clogged filters can restrict airflow and reduce drying efficiency. Cleaning the lint filter after every use will help optimize drying times.

How can I adjust the drying time on my Bosch EcoLogixx 7S dryer?

Depending on the program selected, you may be able to adjust the drying time using the Time Dry function. Refer to the manual to identify the specific drying programs that allow for time adjustment and follow the instructions provided.

Why doesn't my Bosch EcoLogixx 7S dryer seem to be heating properly?

Check that the dryer is connected to a power source and the circuit breaker is not tripped. Additionally, verify that the dryer's temperature settings are appropriate for the load being dried. If the issue persists, consult the troubleshooting section in the manual for further guidance.

Does the Bosch EcoLogixx 7S WTW8656ECO have a freestanding placement?

Yes, the Bosch EcoLogixx 7S WTW8656ECO has a freestanding placement. This means that it is not built into a structure and can be placed anywhere in the home.

Is the drying system of the Bosch EcoLogixx 7S WTW8656ECO condensation?

Yes, the Bosch EcoLogixx 7S WTW8656ECO has a condensation drying system. This means that it collects moisture from the air during the drying process, making it more efficient and reducing the need for an external vent.

Does the Bosch EcoLogixx 7S WTW8656ECO have a built-in display?

Yes, the Bosch EcoLogixx 7S WTW8656ECO has a built-in display. This makes it easier for the user to view and control the settings of the dryer.

Does the Bosch EcoLogixx 7S WTW8656ECO have an anti-crease function?

Yes, the Bosch EcoLogixx 7S WTW8656ECO has an anti-crease function. This means that it incorporates a cycle specifically designed to reduce creases in clothing, making it easier to iron or wear straight from the dryer.

Does the Bosch EcoLogixx 7S WTW8656ECO have a delayed start timer?

Yes, the Bosch EcoLogixx 7S WTW8656ECO has a delayed start timer. This allows the user to set a specific time for the dryer to start, giving them more flexibility and convenience in their laundry routine.

Is the manual of the Bosch EcoLogixx 7S WTW8656ECO available in English?

Yes, the manual of the Bosch EcoLogixx 7S WTW8656ECO is available in English .

Is your question not listed? Ask your question here

No results