View the manual for the Bosch EasyDrill 12 here, for free. This manual comes under the category drill machines and has been rated by 3 people with an average of a 8.1. This manual is available in the following languages: English. Do you have a question about the Bosch EasyDrill 12 or do you need help? Ask your question here


| Brand | Bosch |
| Model | EasyDrill 12 | 0 603 972 90V |
| Product | drill machine |
| EAN | 3165140886390 |
| Language | English |
| Filetype | User manual (PDF) |
| Soft grip | Yes |
| Reverse | Yes |
| Drilling, Screwdriving | |
| Chuck type | Keyless |
| Product design | Pistol grip drill |
| Built-in light | Yes |
| Drilling | Yes |
| Screwdriving | Yes |
| Torque settings | 21 |
| Maximum torque (soft applications) | 14 N⋅m |
| Number of gears | 2 |
| Torque (max) | 22 N⋅m |
| Sound level uncertainty | 1.5 dB |
| Sound pressure level | 71 dB |
| Sound power level | 82 dB |
| Vibration level (metal drilling) | 2.5 m/s² |
| Idle speed (1st gear) | 350 RPM |
| Idle speed (2nd gear) | 1100 RPM |
| Screw diameter (max) | 6 mm |
| Drilling diameter in wood (max) | 20 mm |
| Drilling diameter in steel (max) | 8 mm |
| Maximum torque (hard applications) | 22 N⋅m |
| Vibration emission | 2.5 m/s² |
| Product color | Black, Green, Red |
| Electronic Cell Protection (ECP) | Yes |
| Uncertainty K | 1.5 m/s² |
| Battery level indicator | Yes |
| Power source | Battery |
| Battery technology | Lithium-Ion (Li-Ion) |
| Battery voltage | 12 V |
| Battery capacity | 2.5 Ah |
| Screwdriver bit | Yes |
| Drill bit included | Yes |
| Number of batteries included | 1 pc(s) |
| Battery charger included | Yes |
| Carrying case | Yes |
| Battery included | Yes |
| Weight | 950 g |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Bosch EasyDrill 12 below.
1. Soak the rusty part in vinegar until completely soaked through. 2. Let the vinegar work on the rust for 24 hours. 3. Remove the rust with a wire brush or aluminium foil.
The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.
The amount of sound varies a lot per brand and type of drill machine, it is therefore wise to wear hearing protection to be sure.
The Bosch EasyDrill 12 has a weight of 950 g.
Yes, the Bosch EasyDrill 12 has a soft grip. This means that it is designed to provide a comfortable and secure grip for the user, reducing fatigue and improving control during use.
The Bosch EasyDrill 12 has 21 torque settings. This allows the user to easily adjust the drill's power and control for different applications, providing versatility in use.
Yes, the Bosch EasyDrill 12 has a reverse function. This is useful for tasks such as removing screws or backing out drill bits, enhancing convenience and efficiency for the user.
Yes, the Bosch EasyDrill 12 comes with a battery level indicator. This feature allows the user to easily monitor the remaining battery power, ensuring that they have enough charge for the job and preventing unexpected power loss.
The Bosch EasyDrill 12 has 2 gears. This enables the user to choose between different speed settings, allowing for greater control and precision depending on the task at hand.
To adjust the impact rate of the Bosch EasyDrill 12, follow these steps: 1. Set the operating mode presetting ring (located at position 4) to the "impact drilling" symbol. This can be done by rotating the ring until the symbol aligns with the indicator. 2. Preselect the required torque using the torque presetting ring (located at position 3). The ring has 20 stages, allowing you to choose the desired torque setting. When the correct setting is used, the application tool will stop when the screw is driven flush into the material or when the set torque has been reached. 3. Adjust the speed of the power tool by pressing the on/off switch (located at position 10) to varying extents. Applying light pressure on the switch results in a low rotational speed, while increasing pressure increases the speed. 4. To adjust the speed/impact rate, press the on/off switch to varying extents. Applying light pressure results in a low rotational speed/impact rate, while increasing pressure increases the speed/impact rate. By following these steps, you can easily adjust the impact rate of the Bosch EasyDrill 12 according to your specific drilling needs.
If the mechanical gear selection is not working on your Bosch EasyDrill 12, there could be a few possible reasons. Here are some steps to troubleshoot the issue: 1. Check if the power tool is turned off. The mechanical gear selection will not work if the power tool is in operation. Make sure to switch off the tool before attempting to adjust the gear selection. 2. Verify that the gear selector is properly engaged. The gear selector is located on the top of the tool and allows you to choose between two speed ranges. Ensure that the gear selector is securely positioned in either Gear I or Gear II. 3. Inspect the gear selector for any obstructions or debris. Sometimes, dirt or debris can accumulate around the gear selector, preventing it from moving smoothly. Clean the area around the gear selector and ensure there are no obstructions. 4. If the issue persists, it is possible that there may be a mechanical fault with the gear selector mechanism. In this case, it is recommended to contact Bosch customer support or take the tool to an authorized service center for further assistance. By following these steps, you can troubleshoot the mechanical gear selection issue on your Bosch EasyDrill 12 and determine the cause of the problem.
If the on/off switch is not starting the Bosch EasyDrill 12, there could be a few possible reasons. Here are some steps to troubleshoot the issue: 1. Check if the battery is properly inserted into the handle of the power tool. Ensure that the battery is fully engaged and flush with the handle. 2. Verify that the battery is charged. If the battery is low or not charged, it may not provide enough power to start the tool. Try charging the battery fully and then reinsert it into the handle. 3. Inspect the on/off switch for any obstructions or debris. Sometimes, dirt or debris can accumulate around the switch, preventing it from functioning properly. Clean the area around the switch and ensure there are no obstructions. 4. If the issue persists, try removing the battery from the power tool and reinserting it. This can help reset the tool and may resolve any temporary issues. 5. If none of the above steps solve the problem, it is possible that there may be a fault with the on/off switch or the power tool itself. In this case, it is recommended to contact Bosch customer support or take the tool to an authorized service center for further assistance. By following these steps, you can troubleshoot the issue of the on/off switch not starting the Bosch EasyDrill 12 and determine the cause of the problem.
The fully automatic spindle lock (Auto-Lock) feature on the Bosch EasyDrill 12 is designed to make it easier to change drill bits or screwdriver bits. Here's how it works: 1. Start by ensuring that the power tool is turned off. This is important for safety reasons. 2. When the power tool is not in operation, the spindle and tool holder are automatically locked. This means that you can change the drill bit or screwdriver bit without the spindle rotating. 3. To unlock the spindle, simply press and hold the on/off switch. This will release the spindle lock and allow you to change the bit. 4. While holding the on/off switch, insert the desired drill bit or screwdriver bit into the tool holder. Make sure it is securely inserted. 5. Release the on/off switch to engage the spindle lock again. This will lock the bit in place and ensure it doesn't rotate during operation. By following these steps, you can easily utilize the fully automatic spindle lock (Auto-Lock) feature on the Bosch EasyDrill 12 to change drill bits or screwdriver bits quickly and securely.
The speed of the Bosch EasyDrill 12 may be reduced during heavy loading or temperature changes due to its temperature-dependent overload protection feature. Here's why: 1. Under normal conditions of use, the power tool is designed to operate at its full speed and power. However, during heavy loading or when the temperature exceeds the permitted battery temperature range, the speed is automatically reduced. 2. The temperature-dependent overload protection feature is in place to prevent the power tool from overheating and to protect the battery from damage. When the tool senses heavy loading or temperature changes, it adjusts the speed to a lower level to prevent excessive heat buildup. 3. By reducing the speed, the power tool can continue to operate safely and efficiently, even under challenging conditions. This helps to prolong the lifespan of the tool and ensures optimal performance. 4. If you notice a reduction in speed during heavy loading or temperature changes, it is a normal operation of the Bosch EasyDrill 12's temperature-dependent overload protection feature. Once the loading or temperature returns to normal, the speed will resume its regular level. By incorporating this temperature-dependent overload protection feature, the Bosch EasyDrill 12 ensures safe and reliable operation, even in demanding situations.
Yes, the manual of the Bosch EasyDrill 12 is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Bosch and is the answer not in the manual?
Question and answer
Number of questions: 0