View the manual for the Bosch DUL62FA51 here, for free. This manual comes under the category exhaust hoods and has been rated by 1 people with an average of a 9. This manual is available in the following languages: Universal. Do you have a question about the Bosch DUL62FA51 or do you need help? Ask your question here





| Brand | Bosch |
| Model | DUL62FA51 | DUL62FA51 |
| Product | exhaust hood |
| EAN | 4242005133895 |
| Language | Universal |
| Filetype | Energy label (PDF) |
| Maximum extraction power | 250 m³/h |
| Type of extraction | Ducted |
| Fluid dynamic efficiency class | E |
| Lighting efficiency class | E |
| Grease filtering efficiency class | D |
| Number of speeds | 3 |
| Noise level | 68 dB |
| Noise level (low speed) | 53 dB |
| Grease filter type | Fleece |
| Energy efficiency class | D |
| Connected load | 119 W |
| Motor power | 115 W |
| AC input voltage | 220-240 V |
| AC input frequency | 50 Hz |
| Annual energy consumption | 69.3 kWh |
| Width | 600 mm |
| Depth | 482 mm |
| Height | 150 mm |
| Weight | 5676 g |
| Type | Wall-mounted |
| Product color | Stainless steel |
| Control type | Buttons |
| Cord length | 1.45 m |
| Built-in display | No |
| Exhaust connection diameter | 120 mm |
| Bulb power | 4 W |
| Number of bulbs | 1 bulb(s) |
| Bulb type | LED |
| Illuminance | 45 lx |
| Lighting position | Front |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Bosch DUL62FA51 below.
The Bosch DUL62FA51 has a weight of 5676 g.
The carbon filter should be replaced every three to twelve months.
The metal grease filters should be cleaned every eight to ten weeks.
The model number of the hood is usually found on a white label inside the hood.
The Bosch DUL62FA51 has a height of 150 mm.
The Bosch DUL62FA51 has a width of 600 mm.
The Bosch DUL62FA51 has a depth of 482 mm.
The Bosch DUL62FA51 has energy label D.
The maximum extraction power of the Bosch DUL62FA51 is 250 m³/h. This means that it has a decent suction power to effectively remove cooking odors and steam from the kitchen.
The noise level of the Bosch DUL62FA51 on low speed is 53 dB. This is relatively quiet, allowing for a more peaceful cooking experience.
The grease filtering efficiency class of the Bosch DUL62FA51 is D. This indicates that it has a moderate level of efficiency in removing grease particles from the air.
The Bosch DUL62FA51 has 3 speeds. This allows for greater control over the extraction power and noise level, catering to different cooking needs and preferences.
The annual energy consumption of the Bosch DUL62FA51 is 69.3 kWh. This is relatively low, indicating that it is energy-efficient and can help in saving on electricity costs.
To adjust the fan speed on the Bosch DUL62FA51 exhaust hood, follow these steps: 1. Locate the control panel on the exhaust hood. 2. Look for the slider or switch labeled "Lüfter" or "Ventilator" (German for fan). 3. Slide the control to the desired fan speed level. There are typically three levels available. 4. Adjust the fan speed based on the current conditions. Choose a higher fan speed for strong vapors or odors. 5. When the fan is turned on, an LED indicator will light up to indicate that the fan is running. 6. To turn off the fan, slide the control to the "0" position. Remember to adjust the fan speed according to your cooking needs and the intensity of the cooking fumes. Higher fan speeds are recommended for more intense cooking activities.
There could be several reasons why the lighting is not working on the Bosch DUL62FA51 exhaust hood. Here are the possible solutions: 1. Check if the power cord is properly plugged into the electrical outlet. Ensure that there is a secure connection. 2. Verify if there is a power outage in your area. Check if other kitchen appliances are functioning properly. 3. Inspect the fuse box to see if the fuse for the exhaust hood is intact. Replace the fuse if necessary. 4. If the lighting consists of LED lamps, they might be defective. Follow the instructions in the manual to replace the LED lamps. Make sure to use the same type and wattage of lamps. 5. If none of the above steps resolve the issue, it is recommended to contact the customer service of Bosch for further assistance. Please note that these troubleshooting steps are provided as a general guide and may vary depending on the specific situation.
To clean and maintain the Bosch DUL62FA51 exhaust hood, follow these steps: 1. Ensure that the appliance is not hot before cleaning. Allow it to cool down. 2. Disconnect the power by unplugging the power cord or turning off the fuse in the fuse box. 3. Use a damp cloth to clean the exterior surfaces of the exhaust hood. For stainless steel surfaces, use warm soapy water and wipe in the direction of the grain. Avoid using abrasive or alcohol-based cleaners. 4. For lacquered surfaces, clean with a damp cloth and dry with a soft cloth. Do not use stainless steel cleaners. 5. Clean aluminum and plastic surfaces with a glass cleaner and a soft cloth. 6. To clean the grease filter, remove it every two months. Press on the locking device on both sides of the filter, open it downwards, and remove it. Clean the filter and the inside of the appliance. 7. For glass surfaces, use a glass cleaner and a soft cloth. Do not use glass scrapers. 8. Clean the control elements with a damp cloth and dry with a soft cloth. Avoid using wet cloths on the control elements to prevent electrical shock or damage to the electronics. Follow these cleaning and maintenance instructions to keep your Bosch DUL62FA51 exhaust hood in good condition.
To clean different surfaces of the Bosch DUL62FA51 exhaust hood, use the following cleaning agents: 1. Stainless Steel: Use warm soapy water to clean stainless steel surfaces. Wipe with a cleaning cloth and dry with a soft cloth. Clean in the direction of the grain. Avoid using sharp or abrasive cleaners, strong alcohol-based cleaners, and hard scrubbing sponges. 2. Lacquered Surfaces: Clean lacquered surfaces with warm soapy water. Use a damp cleaning cloth and dry with a soft cloth. Do not use stainless steel cleaners. 3. Aluminum and Plastic: Use a glass cleaner to clean aluminum and plastic surfaces. Wipe with a soft cloth. 4. Glass: Clean glass surfaces with a glass cleaner. Use a soft cloth and avoid using a glass scraper. 5. Control Elements: Clean control elements with warm soapy water. Use a damp cleaning cloth and dry with a soft cloth. Avoid using wet cloths on control elements to prevent electrical shock or damage to the electronics. Do not use stainless steel cleaners. By using the appropriate cleaning agents for each surface, you can effectively clean and maintain the Bosch DUL62FA51 exhaust hood.
To adjust the fan speed on the Bosch DUL62FA51 exhaust hood, follow these steps: 1. Locate the control panel on the exhaust hood. 2. Look for the slider or switch labeled "Lüfter" or "Ventilator" (German for fan). 3. Slide the control to the desired fan speed level. There are typically three levels available. 4. Adjust the fan speed based on the current cooking conditions. For stronger odors or heavy cooking, choose a higher fan speed. 5. When you're finished cooking, slide the control back to the "0" position to turn off the fan. Remember to adjust the fan speed according to your specific needs and the intensity of cooking odors. By following these steps, you can easily adjust the fan speed on the Bosch DUL62FA51 exhaust hood to ensure efficient ventilation in your kitchen.
There could be several reasons why the lighting is not working on the Bosch DUL62FA51 exhaust hood. Here are the steps to troubleshoot the issue: 1. Check if the exhaust hood is properly connected to the power source. Ensure that the plug is securely inserted into the outlet. 2. Verify if there is a power outage in your home by checking if other kitchen appliances are functioning. 3. Inspect the fuse box to see if the fuse for the exhaust hood is intact. Replace the fuse if necessary. 4. If the above steps do not resolve the issue, it is possible that the LED lights are defective and need to be replaced. - To replace the LED lights, follow these steps: a. Lift the lamp cover slightly and push it towards the outside of the hood. b. Unscrew the faulty LED light and replace it with a new one of the same type. c. Place the lamp cover back in position. d. Plug the exhaust hood back into the power source or turn on the fuse. 5. If the problem persists after following these steps, it is recommended to contact the Bosch customer service for further assistance. By following these troubleshooting steps, you can identify and resolve the issue with the lighting on the Bosch DUL62FA51 exhaust hood.
To clean and maintain the Bosch DUL62FA51 exhaust hood, follow these steps: 1. Ensure that the appliance is not hot before cleaning. Allow it to cool down. 2. Disconnect the power by unplugging the hood or turning off the fuse in the fuse box. 3. Use a damp cloth to clean the exterior surfaces of the exhaust hood. For stainless steel surfaces, clean in the direction of the grain to avoid scratching. 4. For grease filters, remove them every two months and replace them with new ones. Clean the interior of the hood after removing the filters. 5. Avoid using sharp or abrasive cleaning agents, strong alcohol-based cleaners, hard scrubbing sponges, high-pressure cleaners, or steam jet devices. 6. For stainless steel surfaces, you can use warm soapy water or specialized stainless steel cleaning products. Apply the cleaning agent thinly with a soft cloth. 7. For lacquered surfaces, use warm soapy water and a soft cloth. Do not use stainless steel cleaners. 8. For aluminum and plastic surfaces, use a glass cleaner and a soft cloth. 9. Clean the control elements with warm soapy water and a soft cloth. Avoid using a wet cloth on the control elements to prevent electrical shock or damage to the electronics. By following these steps, you can effectively clean and maintain the Bosch DUL62FA51 exhaust hood to ensure its optimal performance.
To clean different surfaces of the Bosch DUL62FA51 exhaust hood, use the following cleaning agents: 1. Stainless Steel: - Use warm soapy water to clean stainless steel surfaces. - Wipe with a clean cloth and dry with a soft cloth. - Clean in the direction of the grain to avoid scratching. - Specialized stainless steel cleaning products can also be used sparingly. 2. Lacquered Surfaces: - Use warm soapy water to clean lacquered surfaces. - Wipe with a damp cloth and dry with a soft cloth. - Do not use stainless steel cleaners on lacquered surfaces. 3. Aluminum and Plastic: - Use a glass cleaner to clean aluminum and plastic surfaces. - Wipe with a soft cloth. 4. Glass: - Use a glass cleaner to clean glass surfaces. - Wipe with a soft cloth. - Do not use a glass scraper. 5. Control Elements: - Use warm soapy water to clean control elements. - Wipe with a damp cloth and dry with a soft cloth. - Avoid using a wet cloth on the control elements to prevent electrical shock or damage to the electronics. - Do not use stainless steel cleaners on control elements. By using the appropriate cleaning agents for each surface, you can effectively clean and maintain the Bosch DUL62FA51 exhaust hood.
To adjust the fan speed on the Bosch DUL62FA51 exhaust hood, follow these steps: 1. Locate the control panel on the exhaust hood. 2. Look for the slider or switch labeled "Lüfter" or "Ventilator" (German for fan). 3. Slide the control to the desired fan speed level. There are typically three levels available. 4. Adjust the fan speed based on the current cooking conditions. For stronger odors or heavy cooking, choose a higher fan speed. 5. When you're finished cooking, slide the control back to the "0" position to turn off the fan. Remember to adjust the fan speed according to your specific needs and the intensity of cooking odors. By following these steps, you can easily adjust the fan speed on the Bosch DUL62FA51 exhaust hood to ensure efficient ventilation in your kitchen.
There could be several reasons why the lighting is not working on the Bosch DUL62FA51 exhaust hood. Here are the steps to troubleshoot the issue: 1. Check if the exhaust hood is properly connected to the power source. Ensure that the plug is securely inserted into the outlet. 2. Verify if there is a power outage in your home by checking if other kitchen appliances are functioning. 3. Inspect the fuse box to see if the fuse for the exhaust hood is intact. Replace the fuse if necessary. 4. If the above steps do not resolve the issue, it is possible that the LED lights are defective and need to be replaced. - To replace the LED lights, follow the instructions in the manual: - Lift the lamp cover slightly and push it towards the outside of the device. - Unscrew the lamp and replace it with a new one of the same type. - Place the lamp cover back in position. - Plug the exhaust hood back into the power source or turn on the fuse. 5. If the problem persists after following these steps, it is recommended to contact the customer service for further assistance. By following these troubleshooting steps, you can identify and resolve the issue with the lighting on the Bosch DUL62FA51 exhaust hood.
To clean and maintain the Bosch DUL62FA51 exhaust hood, follow these steps: 1. Ensure that the device is not hot before cleaning. Allow it to cool down. 2. Use a damp cloth to clean the exhaust hood. Do not use sharp or abrasive cleaning agents, strong alcohol-based cleaners, or hard scrubbing sponges. 3. For stainless steel surfaces, clean with warm soapy water using a cleaning cloth. Dry with a soft cloth, following the grain of the stainless steel. 4. For lacquered surfaces, clean with warm soapy water using a damp cleaning cloth. Do not use stainless steel cleaners. 5. For aluminum and plastic surfaces, use a glass cleaner and a soft cloth to clean. 6. Clean the glass surfaces with a glass cleaner and a soft cloth. Do not use glass scrapers. 7. Clean the control elements with a damp cleaning cloth using warm soapy water. Avoid using a wet cloth to prevent the risk of electric shock or damage to the electronics. By following these steps, you can effectively clean and maintain the Bosch DUL62FA51 exhaust hood, ensuring its optimal performance and longevity.
To clean different surfaces of the Bosch DUL62FA51 exhaust hood, use the following cleaning agents: 1. Stainless Steel: - Clean with warm soapy water using a cleaning cloth. - Dry with a soft cloth, following the grain of the stainless steel. - Special maintenance products for stainless steel are available for optimal results. 2. Lacquered Surfaces: - Clean with warm soapy water using a damp cleaning cloth. - Do not use stainless steel cleaners. 3. Aluminum and Plastic: - Use a glass cleaner and a soft cloth to clean. 4. Glass: - Clean with a glass cleaner and a soft cloth. - Do not use a glass scraper. 5. Control Elements: - Clean with warm soapy water using a damp cleaning cloth. - Avoid using a wet cloth to prevent the risk of electric shock or damage to the electronics. - Do not use a cleaning agent for stainless steel. By using the appropriate cleaning agents for each surface, you can effectively clean and maintain the Bosch DUL62FA51 exhaust hood, keeping it in good condition.
Unfortunately, we do not have the manual for the Bosch DUL62FA51 available in English. This manual is available in Universal.
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Bosch and is the answer not in the manual?
Question and answer
Number of questions: 0