View the manual for the Bosch Classixx 7 WAE28369 here, for free. This manual comes under the category washing machines and has been rated by 17 people with an average of a 8.3. This manual is available in the following languages: English. Do you have a question about the Bosch Classixx 7 WAE28369 or do you need help? Ask your question here
| Brand | Bosch |
| Model | Classixx 7 WAE28369 |
| Product | washing machine |
| Language | English |
| Filetype | User manual (PDF) |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Bosch Classixx 7 WAE28369 below.
The washing label of your garment shows the recommended washing temperature.
It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash.
Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash.
Ensure that the power plug is securely connected to the electrical outlet and that the outlet is functioning properly. Also, make sure that the door of the washing machine is fully closed and the water supply is turned on.
Check if the water supply tap is fully open. Additionally, inspect the inlet hose for any kinks or blockages. If necessary, clean or replace the inlet filter.
Make certain that the washing machine is level and all four legs are in firm contact with the floor. Also, ensure that the laundry load is distributed evenly inside the drum to prevent imbalance issues.
Verify that the washing machine is not in contact with other objects that could cause noise or vibrations. Additionally, inspect the drum for any foreign objects like loose coins or buttons, which might be creating the noise.
Firstly, check if the drain hose is correctly positioned and not bent, twisted, or restricted. Additionally, examine the pump filter for any clogs or debris that might be impeding proper drainage. Clean it as needed.
Yes, the manual of the Bosch Classixx 7 WAE28369 is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Bosch and is the answer not in the manual?
Question and answer
Number of questions: 30Getting a warning that the door is not closed although it is. Has anyone else had this problem?
1 comment
If you are receiving a warning that the door is not closed on the Bosch Classixx 7 WAE28369 washing machine, here are some possible causes and solutions: 1. The washing machine door is unlocked: Make sure to lock the door properly. If the door is unlocked, it is possible to add laundry. 2. Temperature too high or water level too high: If the temperature is too high or the water level is too high, it may not be possible to add laundry. Close the washing machine door immediately if necessary and wait until the temperature drops or the water level decreases. Then, select Start/Reload to continue the program. 3. F:16 error code: This error code indicates that the door is not closed properly and laundry may become trapped. Make sure to close the door properly. 4. F:17 error code: This error code can be caused by the water tap not being turned on fully, a kinked or trapped supply hose, or low water pressure. Check and ensure that the water tap is fully turned on, the supply hose is not kinked or trapped, and the water pressure is sufficient. Clean the screen if necessary. 5. F:18 error code: This error code indicates a blockage in the detergent solution pump or the drain hose/waste pipe. Clean the detergent solution pump and the drain hose on the siphon. 6. F:21 error code: This error code indicates a motor fault. 7. F:23 error code: This error code indicates water in the base tub and appliance leaking. 8. E error code: This error code indicates that the childproof lock is activated. Deactivate the childproof lock. If none of these solutions resolve the issue, it is recommended to contact the after-sales service for further assistance.
This answer is automatically generatedWipe inside machine and draw then did a rinse cycle. Now find childproof lock flashing and unable to proceed with a wash. How do I deactivate the childproof lock
1 comment
To disable the childproof lock on the Bosch Classixx 7 WAE28369 washing machine, follow these steps: 1. If the childproof lock is active and the program selector has been adjusted, turn the program selector back to the original program. This will prevent the program from stopping and the symbol will light up again. 2. Keep in mind that the childproof lock can remain active until you want to start the next program, even after turning off the machine. In that case, you must disable the childproof lock before starting the program and enable it again as needed once the program has started.
This answer is automatically generatedDid a rinse cycle now unable to proceed with next wash as childproof lock (key) flashing. Unable to select programs as machine locked with childproof lock. How to deactivate this Please.
2 comments
To deactivate the childproof lock on the Bosch Classixx 7 WAE28369 washing machine, follow these steps: 1. Turn the program selector back to the original program. This will prevent the program from stopping and the childproof lock symbol from flashing. Please make sure to turn the program selector back to the original program to deactivate the childproof lock.
This answer is automatically generatedKey is flashing
The open drum has rotated and got stuck, and we can't unlock it or rotate it. What can we do?
The washing machine is showing F:21 and is not doing anything or letting me open the door to take out the clothes. What does that F:21 mean?
My Bosch displays END plus a key symbol, what does it mean?
This message has been automatically translatedWhatever cycle wash I choose on our Bosch Classixx7 washing h, it runs and goes down to one minute, then goes on for at least another hour - I suspect it is as long as the 90o programme. Long and expensive, and potentially too hot for what we want to wash. Thanks in advance for any suggestion.
When machine is turned on a this Appearsu - 0 - and the sign of Key these symbols flash in the display panel
Twisted this to the left, ( don't ask) now it is leaking when I put a walk on