Bosch B810 manual

Bosch B810
7.5 · 1
PDF manual
 · 3 pages
English
manualBosch B810
Intrusion Alarm Systems | B810 Wireless SDI2 bus interface

B810 Wireless SDI2 bus interface

www.boschsecurity.com
u Dual internal antennas provide spatial and polar RF
signal reception for high reliability
u Cover and wall tamper protection
u Multiple device enrollment options as well as RF
diagnostics ensure efficient and effective installation
u Supports supervision of wireless points (504),
keyfobs (1000), and repeaters (8)
u External status LEDs
RADION wireless from Bosch provides the range,
scalability and exceptional battery life required to
ensure reliable performance and superior quality.
Advanced diagnostics and multiple device enrollment
options make installation and maintenance simple and
cost effective. With a complete line of peripherals,
RADION provides the flexibility for virtually any
application requirement.
System overview
The B810 is a wireless receiver that connects RADION
wireless peripherals such as the motion and specialty
detectors, keyfobs, panic buttons, door window
contacts, repeaters, and more, to supported Bosch
control panels using the SDI2 Bus connection.
The receiver supports RF communication at 433.42
MHz This frequency features improved penetration,
reflection, and refraction of signal for superior range,
and reliability. The receiver also features dual
antennas to achieve spatial and polar diversity to
further improve RF communication reliability. Enclosed
within the receiver housing for higher security, the
receiver is equipped with tamper protection, and
detects and reports radio frequency interferences. The
receiver supports supervision of wireless points (504),
key fobs (1000), and repeaters (8).
The receiver can be easily accessed and configured for
a compatible control panel using the address switch
on the back of the receiver housing. The receiver
address switch provides a single-digit setting for the
receiver’s address, allowing for ease of installation.
Functions
The receiver uses the RADION wireless protocol which
supports:
SDI2 bus communication
Tamper input processing
RF interference (jamming) detection and reporting
Signal strength and margin reporting
Enroll Device Database management
Address switch addressing
Use the address switch to easily assign a bus address
or setup during installation.
Easy installation
The sliding self-locking enclosure has an integrated
bubble level and a custom gap-free, lift gate style
terminal block to make installation easier, faster, and
more reliable.

View the manual for the Bosch B810 here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Bosch B810 or do you need help? Ask your question here

Need help?

Do you have a question about the Bosch and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Bosch B810 is a not categorized product that is sold individually. It operates on an input voltage of 12 volts. With a width of 139.7 millimeters, a depth of 209.6 millimeters, and a height of 31.8 millimeters, this product has compact dimensions. Unfortunately, with limited information available, a detailed description of the Bosch B810 is not possible. However, it can be inferred that this product is designed for a specific purpose or application but does not fall into a specific category. The Bosch B810's single quantity per pack suggests that it may be a standalone product rather than part of a set or collection. The input voltage of 12 volts indicates that it is compatible with standard voltage requirements. Its width, depth, and height measurements suggest that it has a relatively small form factor, making it potentially suitable for compact spaces or specific installations. While the Bosch B810's specifications provide an idea of its physical attributes and power requirements, additional information would be necessary to create a comprehensive and meaningful description of its features, benefits, or functionality. In summary, due to the lack of available information, a detailed description of the Bosch B810 cannot be provided. Its quantity per pack, input voltage, and physical dimensions are the only known specifications at this time.

General
BrandBosch
ModelB810 | B810
Productnot categorized
LanguageEnglish
FiletypeUser manual (PDF)
Features
Product type-
Product colorWhite
Quantity per pack1 pc(s)
Operational conditions
Operating temperature (T-T)0 - 49 °C
Power
Input voltage12 V
Weight & dimensions
Width139.7 mm
Depth209.6 mm
Height31.8 mm
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Bosch B810 below.

What is the height of the Bosch B810?

The Bosch B810 has a height of 31.8 mm.

What is the width of the Bosch B810?

The Bosch B810 has a width of 139.7 mm.

What is the depth of the Bosch B810?

The Bosch B810 has a depth of 209.6 mm.

Is the Bosch B810 suitable for use with a 220V power supply?

No, the Bosch B810 has an input voltage of 12V, so it is not suitable for use with a 220V power supply. This means that the user needs to ensure they have a suitable power source or use a voltage converter to properly operate the product.

How many units are included in a single pack of the Bosch B810?

The Bosch B810 comes with a quantity of 1 pc(s) per pack. This means that each pack includes only one unit of the product. It is worth noting that some products may come with multiple units in a pack, so this could be a factor to consider when comparing the Bosch B810 to similar products on the market.

How can I troubleshoot if the Bosch B810 is not operating within the recommended temperature and humidity conditions?

To troubleshoot if the Bosch B810 is not operating within the recommended temperature and humidity conditions, follow these steps: 1. Check the operating environment: Ensure that the temperature range is between 0°C to +49°C (+32°F to +120°F) and the relative humidity is up to 93% non-condensing. Verify that the B810 is being used indoors as intended. 2. Verify power supply: Make sure the B810 is receiving the correct power/voltage of 10-14 VDC, with a nominal voltage of 12 VDC. Check the power source and ensure it is within the specified range. 3. Inspect for obstructions: Ensure that there are no physical obstructions blocking the B810's ventilation or air circulation. Remove any objects that may be blocking the device. 4. Check for interference: Verify that there are no sources of RF interference near the B810. Other electronic devices or nearby wireless equipment can cause interference. Move the B810 away from potential sources of interference. 5. Contact technical support: If the B810 continues to have issues operating within the recommended temperature and humidity conditions, contact Bosch technical support for further assistance. They can provide additional troubleshooting steps or arrange for repairs if necessary. Remember to always refer to the Bosch B810 manual for specific instructions and guidelines.

What should I do if the Bosch B810 wireless receiver is not detecting intrusion alarms?

To troubleshoot if the Bosch B810 wireless receiver is not detecting intrusion alarms, follow these steps: 1. Check the power supply: Ensure that the B810 receiver is receiving the correct power/voltage of 10-14 VDC, with a nominal voltage of 12 VDC. Verify the power source and make sure it is within the specified range. 2. Verify device enrollment: Ensure that the intrusion alarms, such as motion detectors or door/window contacts, are properly enrolled with the B810 receiver. Follow the instructions in the manual to enroll the devices correctly. 3. Check signal strength: Verify that the intrusion alarms are within the range of the B810 receiver. Ensure that there are no physical obstructions or interference that may weaken the signal strength. Move the receiver or the devices closer to improve the signal strength if needed. 4. Inspect for tampering: Check if the intrusion alarms or the B810 receiver have been tampered with. Ensure that the devices are securely mounted and that there are no loose connections or physical damage. 5. Contact technical support: If the B810 receiver still does not detect intrusion alarms after following these steps, it is recommended to contact Bosch technical support for further assistance. They can provide additional troubleshooting steps or arrange for repairs if necessary. Remember to always refer to the Bosch B810 manual for specific instructions and guidelines.

How can I troubleshoot if the Bosch B810 wireless receiver is not properly connected to RADION wireless peripherals?

To troubleshoot if the Bosch B810 wireless receiver is not properly connected to RADION wireless peripherals, follow these steps: 1. Verify device enrollment: Ensure that the RADION wireless peripherals, such as motion detectors, specialty detectors, keyfobs, panic buttons, door/window contacts, and repeaters, are properly enrolled with the B810 receiver. Follow the instructions in the manual to enroll the devices correctly. 2. Check RF communication frequency: Confirm that the B810 receiver and the RADION wireless peripherals are operating on the same RF communication frequency of 433.42 MHz. This frequency provides improved signal penetration, reflection, and refraction for superior range and reliability. 3. Inspect physical connections: Check the physical connections between the B810 receiver and the RADION wireless peripherals. Ensure that the connections are secure and properly seated. Verify that there are no loose or damaged wires or connectors. 4. Verify power supply: Make sure that the B810 receiver is receiving the correct power supply within the specified voltage range of 10-14 VDC, with a nominal voltage of 12 VDC. Check the power source and ensure it is providing the required power. 5. Contact technical support: If the B810 receiver still does not properly connect to the RADION wireless peripherals after following these steps, it is recommended to contact Bosch technical support for further assistance. They can provide additional troubleshooting steps or arrange for repairs if necessary. Remember to always refer to the Bosch B810 manual for specific instructions and guidelines.

What should I do if the Bosch B810 receiver is not functioning as expected in terms of RF communication frequency and signal strength?

To troubleshoot if the Bosch B810 receiver is not functioning as expected in terms of RF communication frequency and signal strength, follow these steps: 1. Check RF communication frequency: Verify that the B810 receiver and the RADION wireless peripherals are operating on the same RF communication frequency of 433.42 MHz. This ensures compatibility and optimal signal transmission. 2. Inspect antenna placement: Ensure that the B810 receiver's dual internal antennas are properly positioned. Place the receiver in a central location, away from obstructions, and ensure that the antennas are fully extended and oriented vertically. 3. Verify signal strength: Use the B810 receiver's signal strength and margin reporting feature to assess the signal quality. Check the signal strength indicator on the receiver or use a compatible Bosch control panel to monitor the signal strength. If the signal strength is weak, consider repositioning the receiver or adding a repeater to improve coverage. 4. Check for interference: Identify and eliminate potential sources of RF interference, such as other wireless devices or electronic equipment operating on similar frequencies. Move the B810 receiver away from these sources or use shielding techniques to minimize interference. 5. Contact technical support: If the B810 receiver continues to have issues with RF communication frequency and signal strength after following these steps, it is recommended to contact Bosch technical support for further assistance. They can provide additional troubleshooting steps or arrange for repairs if necessary. Remember to always refer to the Bosch B810 manual for specific instructions and guidelines.

How can I troubleshoot if the address switch on the Bosch B810 receiver is not assigning a bus address or setting up the receiver correctly during installation?

To troubleshoot if the address switch on the Bosch B810 receiver is not assigning a bus address or setting up the receiver correctly during installation, follow these steps: 1. Verify address switch position: Check the position of the address switch on the B810 receiver. Ensure that the switch is set to the desired bus address or installation mode according to the instructions provided in the manual. 2. Confirm switch functionality: Ensure that the address switch is functioning properly. Check for any physical damage or loose connections. If necessary, try toggling the switch a few times to ensure it is making a proper connection. 3. Power cycle the receiver: Turn off the power to the B810 receiver and disconnect it from the power source. Wait for a few seconds, then reconnect the power and turn on the receiver. This can help reset the receiver and address switch functionality. 4. Check for bus communication: Verify that the B810 receiver is properly connected to the control panel using the SDI2 Bus connection. Ensure that the wiring is correct and secure. Check for any loose or damaged wires. 5. Contact technical support: If the address switch on the B810 receiver still does not assign a bus address or set up the receiver correctly after following these steps, it is recommended to contact Bosch technical support for further assistance. They can provide additional troubleshooting steps or arrange for repairs if necessary. Remember to always refer to the Bosch B810 manual for specific instructions and guidelines.

Is the manual of the Bosch B810 available in English?

Yes, the manual of the Bosch B810 is available in English .

Is your question not listed? Ask your question here

No results