Bosch 10P manual

Bosch 10P
7.5 · 1
PDF manual
 · 11 pages
English
manualBosch 10P

Installation

Install only on an external wall, as close as possible to the most frequently used hot
tap. Use a heat shield (accessory item part number 9 708 061 400) if the unit is to be installed
on a combustible surface. Allow minimum air gap of 10 mm between the flue and the heat
shield, (refer figure 2).
Ensure that the flue terminal is clear of any combustible material, and avoid
installation in a marine environment.
Install the appliance such that the base of the appliance is not more than 1.3 metres
and not less than 0.5 meters from the ground, and allow for easy access to service heater.
Secure heater to wall using two 10g X
5
/
16
hex head wood screws (Ramset 610041 or similar).
Locate head of screw in the key hole of the top mounting bracket.
Appliance Dimensions
A B C D
13P 405
mm
845
mm
533
mm
240
mm
16P 460
mm
936
mm
550
mm
240
mm
Figure 3

Pipe Connections Refer to Fig. 1 for locations

Hot and Cold water ½" male
Natural gas ¾" female
L.P. gas ½" male
A gas cock must be installed in the gas supply line with provision to disconnect the
appliance. Install gate valve or full flow ball valve (fixed mechanism type) in cold water supply.

A non return valve must not be fitted. For example duo valve

We recommend that all hot water pipes be lagged if the runs are long or exposed,
and water-proof lagging should be used on all external hot water pipes. If the water supply
pressure exceeds 80% of the specified maximum, install a pressure limiting valve.
If installing a pressure limiting valve fit a cold expansion valve between the limiting valve and
the appliance. PLV = 500kPa Cold expansion = 700kPa
Refer to AG 601 and AS3500.1 for the relevant pipe size.
NOTE: Service calls for incorrect pipe sizing will NOT be covered under warranty.

Water Filter

If sludge or foreign matter is or may be present in the water supply, it is
recommended that a suitable filter be incorporated in the water supply line to the heater. All
pipes should be well flushed before connection is made.
A water filter/strainer is installed in the inlet of the brass water valve inside the appliance.
Page2
25/10/2011
9 708 069 951

View the manual for the Bosch 10P here, for free. This manual comes under the category water heaters & boilers and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Bosch 10P or do you need help? Ask your question here

Need help?

Do you have a question about the Bosch and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 11
K
Kevin Raymond MoffattApril 29, 2023

I have a BOSCH 10P WATER WIZARD gas hot water system. I have a problem trying to turn the heater on. The off button won't release making it impossible to turn the heater on. Is there a way to make it release or at least turn the heater on? Thank you for your time Kevin Moffatt

I have a BOSCH 10P WATER WIZARD gas hot water system. I have a problem trying to turn the heater on. The off button won't rel...
zoom-in
View photo
3 comments
E
Emma of manua.lsDecember 19, 2023

To turn on the Bosch 10P water heater, follow these steps: 1. Make sure that all hot water taps are turned off before attempting to light the appliance. 2. If the pilot light is extinguished, wait for 5 minutes before attempting to relight the appliance. 3. With the gas supply turned off, loosen the captive screw in the burner pressure test point on the left-hand side of the burner manifold. 4. Attach a "U" tube manometer, turn on the gas supply, and light the appliance. 5. Open a hot water tap to draw off more than 10 liters per minute. In summer or when the inlet cold water is above 15°C, it may be necessary to temporarily increase the maximum water flow to compensate for the thermostat turning down the gas rate. 6. Adjust the pressure if necessary at the pressure regulator fitted to the gas supply pipe. 7. The gas supply pressure must be as stated on the appliance rating label, located at the bottom right-hand inside the rear panel. The gas pressure at the inlet test point will be approximately 100 pascals less than the supply pressure due to the pressure drop across the regulator.

This answer is automatically generated
S
ShannonJune 15, 2023

Just had to do this as Ignitikn button was not having any effect on the OFF button. So this is what got it sorted for me! 1. Take off the main case to access the button plate 2. Unscrew both sets of screws to remove plate. 3. FYI: Slider button comes off with it. 4. Press on ignition button and this will cause the OFF button to reset its position. I continued the process of lighting the system while here, put plate and screws back in, then reattached main case. All sorted.

I
IqbalNovember 22, 2023

Hi Kevin, did you sort out your issue? I just had the same issue as yours.

D
Dave June 2, 2024

How can I prevent my 10P water heater pilot light from blowing out so often in high winds?

S
ShannonJune 15, 2023

Does anyone actually read and respond to these questions? Some questions already asked I was chasing the answer for

J
John AltoftJuly 27, 2023

I am a renter not a technician. I have a Bosch water wizard 10P which seems to use an excessive amount of gas. How do I reduce the amount of gas the system uses?

C
ColleenAugust 21, 2021

My Bosch P10 pilot light keeps going out plus water not hot enough unless turn cold water on but then water cold.

M
MickJune 11, 2023

How to increase the temp of the hot water

1 comment
S
ShannonJune 15, 2023

Take off main case and turn the big dial at the bottom to the right

J
Janet BramwellJuly 2, 2023

Water not getting hot enough, have turned up heat as per manual instructions. How do I turn down water flow. I have not had to do this previously in winter.

R
RudyMarch 2, 2023

Hot water supply gradually fades to cold on lower pressure.

J
June M WardropJanuary 19, 2024

HOW TO REDUCE TEMPERATURE OF WATER

The Bosch 10P water heater & boiler is a reliable and durable heating appliance designed to provide hot water for domestic use. It is manufactured by Bosch, a reputable company known for producing quality home appliances. The Bosch 10P is specifically designed to meet the demands of households requiring a constant supply of hot water. It is equipped with innovative technology that ensures efficient heating and minimal energy consumption. This water heater & boiler is built with premium materials that guarantee longevity and reliability over time. The Bosch 10P comes in a compact and space-saving design, allowing for easy installation and integration into any home. It is equipped with advanced safety features, providing peace of mind to users. While specific specifications may vary, the Bosch 10P is capable of delivering a consistent flow of hot water, meeting the needs of an average-sized household. It operates silently, minimizing any disturbance to the household. Furthermore, the Bosch 10P boasts high efficiency, meaning it maximizes the utilization of energy, resulting in potential cost savings on electricity or gas bills. Its user-friendly interface allows for easy temperature control and adjustment, ensuring personalized comfort. Overall, the Bosch 10P water heater & boiler is a reliable and efficient heating appliance that delivers consistent hot water supply while prioritizing safety and energy efficiency.

General
BrandBosch
Model10P
Productwater heater & boiler
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Bosch 10P below.

What is the ideal room temperature?

Most people find that the ideal room temperature is between 19 and 22 degrees Celsius.

Why is there no hot water coming out of my Bosch 10P water heater and boiler?

There could be multiple reasons for this issue. First, check if the power supply to the unit is functioning properly. Ensure that the circuit breaker is not tripped. Additionally, verify if the water supply valve is fully open. If these steps do not resolve the issue, it is recommended to consult a qualified technician to inspect the unit further.

How can I adjust the temperature on my Bosch 10P water heater and boiler?

To adjust the temperature, you need to locate the temperature control knob on the front panel of the unit. Turn the knob clockwise to increase the temperature and counterclockwise to decrease it. Make sure to set the temperature to a safe and desirable level to prevent scalding or inadequate heating.

What should I do if my Bosch 10P water heater and boiler is leaking?

If you notice any leaks, it is important to take immediate action. Turn off the power supply to the unit and close the water supply valve to prevent further damage. Contact a qualified technician to inspect the appliance, as leaking may indicate a faulty valve, pipe, or pressure relief system that needs professional attention to ensure proper functioning.

How often should I flush and maintain my Bosch 10P water heater and boiler?

Regular maintenance is crucial for optimal performance and longevity of your water heater and boiler. It is recommended to flush the system at least once a year to remove sediment buildup that may affect efficiency. Consult the manual for detailed instructions on the flushing procedure. Additionally, scheduling professional maintenance every 2-3 years is advised to ensure all components are working correctly and to address any potential issues.

Why is my Bosch 10P water heater and boiler making unusual noises?

Unusual noises can be caused by various factors, such as mineral buildup, loose components, or pressure imbalances. It is essential to identify the source of the noise to determine the appropriate action. Inspect the unit for visible signs of loose parts or leaks. If the noises persist, it is recommended to contact a qualified technician who can diagnose and resolve the issue properly.

Is the manual of the Bosch 10P available in English?

Yes, the manual of the Bosch 10P is available in English .

Is your question not listed? Ask your question here

No results