BenQ W2000W manual

BenQ W2000W
5.4 · 1
PDF manual
 · 63 pages
English
manualBenQ W2000W
24
Operation

Selecting an input source

The projector can be connected to multiple equipment at the same time. However, it only displays one
full screen at a time. When starting up, the projector automatically searches for the available signals.
If you want the projector to always automatically search for the signals:
• Under the Advanced OSD menu, go to the System Setup : Basic menu, and enable Auto
Source. (see "Auto Source" on page 41)
• Under the Basic OSD menu, if there’s no signal connected to the projector, go to Auto Source and
enable it; if there are signals connected, go to the Settings menu, and then enable Auto Source.
(see "Auto Source" on page 31 and 32)
To select the video source:
1. Press SOURCE on the projector or remote control to display the
source selection bar.
2. Press / until your desired signal is selected and press OK.
Once detected, the selected source information is displayed on the
screen for seconds. If there are multiple pieces of equipment connected
to the projector, repeat steps 1-2 to search for another signal.
The native display resolution of this projector is in a 16:9 aspect ratio. For best
display picture results, you should select and use an input signal which outputs
at this resolution. Any other resolutions will be scaled by the projector
depending upon the Aspect Ratio setting, which may cause some image
distortion or loss of picture clarity. See "Aspect Ratio" for details.

Connecting a wireless signal

To connect to a wireless source, make sure the Wireless FHD transmitter
(Tx) and receiver (Rx) are correctly installed and the Wireless signal lights
green* on the source selection bar.
1. Press / to select Wireless from the source selection bar and press
OK to display the wireless selection window.
2. Press / to select a signal and press OK to confirm.
*Wireless signal LED behavior

Renaming an input source

You may rename the current input source on the source selection bar.
To do this, first and foremost, you have to access the Advanced OSD menu (see page 28 for details).
1. Press MENU and then use / to go to System Setup : Basic.
2. Press to select Source Rename and press OK to display the Source Rename window.
3. Press / / / until your desired character is selected.
4. When done, press BACK to save your changes and exit.
On the source selection bar On the wireless selection window
LED Status LED Status
Tx and Rx are connected. Tx is powered.
Tx and Rx are disconnected.
Tx is not powered.
Rx is not powered.
HDMI1
HDMI2/MHL
Video
Component
PC
Source
Wireless

Manual

View the manual for the BenQ W2000W here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 5.4. This manual is available in the following languages: English. Do you have a question about the BenQ W2000W or do you need help? Ask your question here

Index

Need help?

Do you have a question about the BenQ and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

BenQ W2000W specifications

Below you will find the product specifications and the manual specifications of the BenQ W2000W.

The BenQ W2000W video projector utilizes DLP projection technology to deliver high-quality visuals. It supports various video modes, including 480i, 480p, 576i, 576p, 720p, 1080i, and 1080p, ensuring compatibility with different content sources. With a brightness of 2000 ANSI lumens and a contrast ratio of 15000:1, this projector delivers clear and vibrant images on screen. The native aspect ratio of 16:9 and a zoom ratio of 1.3:1 provide flexibility in adjusting the image size according to the viewing environment. The service life of the light source is 3500 hours in standard mode and extends to 6000 hours in economic mode, offering long-term usage without the need for frequent replacements. Featuring an offset of 105%, the projector supports graphics resolutions ranging from 640 x 480 (VGA) to 1920 x 1200 (WUXGA). The W2000W is tuned to achieve Rec. 709 color standards, ensuring accurate and lifelike color reproduction for a cinematic viewing experience. Additionally, the included WDP02 Wireless Full HD Kit enables convenient wireless projection in uncompressed 1080p resolution. In summary, the BenQ W2000W video projector combines advanced technology with precise color calibration to provide a high-quality home cinema experience.

General
BrandBenQ
ModelW2000W | 9H.Y1J77.18G
Productvideo projector
EAN4718755063046
LanguageEnglish
FiletypeUser manual (PDF)
Projector
Projection technologyDLP
Projector brightness2000 ANSI lumens
Contrast ratio (typical)15000:1
Number of colors1.073 billion colors
Native aspect ratio16:9
Keystone correction, vertical-30 - 30 °
Vertical scan range23 - 120 Hz
Horizontal scan range15 - 102 kHz
Screen size compatibility60 - 300 "
Projector native resolution1080p (1920x1080)
Projection distance- m
Video
Supported video modes480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Supported graphics resolutions640 x 480 (VGA), 1920 x 1200 (WUXGA)
Analog signal format systemNTSC, PAL, SECAM
3DYes
Full HDYes
3D ReadyYes
HD-ReadyYes
Lens system
Focal length range16.88 - 21.88 mm
Aperture range (F-F)2.59 - 2.87
Throw ratio1.15 - 1.5:1
Zoom ratio1.3:1
Offset105 %
Vertical lens shift range0 - 10 °
Light source
Service life of light source (economic mode)6000 h
Service life of light source3500 h
Lamp power240 W
Light source typeLamp
Weight & dimensions
Width380.5 mm
Depth277 mm
Height121.7 mm
Weight3600 g
Features
On Screen Display (OSD)Yes
On Screen Display (OSD) languagesARA, BUL, CHI (SIMPL), CHI (TR), CRO, CZE, DAN, DEU, DUT, ENG, ESP, FIN, FRE, GRE, HUN, IND, ITA, JPN, KOR, NOR, POL, POR, RUM, RUS, SWE, THA, TUR
Noise level29 dB
Noise level (economic mode)27 dB
Ports & interfaces
VGA (D-Sub) ports quantity1
Composite video in1
Component video (YPbPr/YCbCr) in1
HDMI ports quantity3
Mobile High-Definition Link (MHL)Yes
PC Audio inYes
USB 2.0 ports quantity3
Serial interface typeRS-232
12V triggerYes
Audio (L/R) in1
S-Video inputs quantity-
DVI portNo
PC Audio outYes
AC (power) inYes
Multimedia
Built-in speaker(s)Yes
Number of built-in speakers2
RMS rated power20 W
Packaging content
Handheld remote controlYes
ManualYes
Cables includedAC
Warranty cardYes
Quick start guideYes
Power
Power sourceAC
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (standby)- W
Display
Built-in displayNo
Design
Product typeStandard throw projector
Product colorBeige, White
Market positioningHome cinema
PlacementDesktop, Ceiling
Network
Ethernet LAN (RJ-45) ports0
Ethernet LANNo
Wi-FiNo
Other features
RS-232 ports1
Storage
Card reader integratedNo
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the BenQ W2000W below.

What is the weight of the BenQ W2000W?

The BenQ W2000W has a weight of 3600 g.

What is the height of the BenQ W2000W?

The BenQ W2000W has a height of 121.7 mm.

What is the width of the BenQ W2000W?

The BenQ W2000W has a width of 380.5 mm.

What is the depth of the BenQ W2000W?

The BenQ W2000W has a depth of 277 mm.

Is the manual of the BenQ W2000W available in English?

Yes, the manual of the BenQ W2000W is available in English .

Is your question not listed? Ask your question here

No results