BenQ MH606 manual

BenQ MH606
5.1 · 1
PDF manual
 · 48 pages
English
manualBenQ MH606
4 Important safety instructions

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information technology
equipment. However, to ensure safe use of this product, it is important that you follow the instructions
mentioned in this manual and marked on the product.
1. Please read this manual before you
operate your projector. Save it for future
reference.
2. Do not look straight at the projector
lens during operation. The intense light
beam may damage your eyes.
3. Refer servicing to qualified service
personnel.
4. Always open the lens shutter (if any) or
remove the lens cap (if any) when the
projector lamp is on.
5. The lamp becomes extremely hot during
operation. Allow the projector to cool for
approximately 45 minutes prior to removing
the lamp assembly for replacement.
6. In some countries, the line voltage is NOT
stable. This projector is designed to operate
safely within a mains voltage between 100 to
240 volts AC, but could fail if power cuts or
surges of ±10 volts occur. In areas where
the mains voltage may fluctuate or cut
out, it is recommended that you
connect your projector through a power
stabilizer, surge protector or
uninterruptible power supply (UPS).
7. Do not block the projection lens with any
objects when the projector is under
operation as this could cause the objects to
become heated and deformed or even cause a
fire. To temporarily turn off the lamp, use the
blank function.
8. Do not operate lamps beyond the rated lamp
life. Excessive operation of lamps beyond the
rated life could cause them to break on rare
occasions.

Manual

View the manual for the BenQ MH606 here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 5.1. This manual is available in the following languages: English. Do you have a question about the BenQ MH606 or do you need help? Ask your question here

Need help?

Do you have a question about the BenQ and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

BenQ MH606 specifications

Below you will find the product specifications and the manual specifications of the BenQ MH606.

General
BrandBenQ
ModelMH606 | 9H.JGX77.13E
Productvideo projector
EAN4718755069925
LanguageEnglish
FiletypeUser manual (PDF)
Network
Wi-Fi-
Ethernet LAN (RJ-45) ports0
Ethernet LANNo
Projector
Projector brightness3500 ANSI lumens
Contrast ratio (typical)10000:1
Projection technologyDLP
Projector native resolution1080p (1920x1080)
Number of colors1.073 billion colors
Native aspect ratio16:9
Keystone correction, vertical-40 - 40 °
Screen size compatibility30 - 300 "
Horizontal scan range15 - 102 kHz
Vertical scan range23 - 120 Hz
Projection distance- m
Video
Full HDYes
Supported graphics resolutions640 x 480 (VGA), 1920 x 1080 (HD 1080), 1920 x 1200 (WUXGA)
Supported video modes480i, 480p, 576i, 576p, 720p, 1080i, 1080p
3DYes
Analog signal format systemNTSC, PAL, SECAM
Supported 3D formatsFrame Sequential, Frame packing, Side by side, Top and bottom
Light source
Lamp power200 W
Lamps quantity1 lamp(s)
Service life of light source5000 h
Service life of light source (economic mode)15000 h
Lamp typeUHP
Light source typeLamp
Lens system
Throw ratio1.49 - 1.64:1
Zoom ratio1.1:1
Focal length range22 - 24.1 mm
Aperture range (F-F)2.56 - 2.68
Offset108 %
Design
Product colorWhite
Product typeStandard throw projector
Market positioningBusiness
PlacementDesktop
Multimedia
Built-in speaker(s)Yes
RMS rated power2 W
Number of built-in speakers1
Image formats supportedJPG
Ports & interfaces
VGA (D-Sub) ports quantity2
S-Video inputs quantity1
Composite video in1
HDMI ports quantity2
DVI portNo
USB 2.0 ports quantity2
Audio (L/R) in0
Headphone outputs1
Microphone inYes
Serial interface typeRS-232
CardBus PCMCIA slot typeNo
Component video (YPbPr/YCbCr) in0
AC (power) inYes
Mobile High-Definition Link (MHL)Yes
Other features
RS-232 ports1
Power
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power sourceAC
Power consumption (typical)260 W
Power consumption (standby)0.5 W
Auto power offYes
Features
Noise level32 dB
Noise level (economic mode)29 dB
On Screen Display (OSD)Yes
On Screen Display (OSD) languagesARA, BUL, CHI (SIMPL), CHI (TR), CRO, CZE, DAN, DEU, DUT, ENG, ESP, FIN, FRE, GRE, HUN, IND, ITA, JPN, KOR, NOR, POL, POR, RUM, RUS, SWE, THA, TUR
Operational conditions
Operating temperature (T-T)0 - 40 °C
Weight & dimensions
Width296 mm
Depth221 mm
Height120 mm
Weight2300 g
Packaging content
Handheld remote controlYes
Remote control typeIR
Cables includedAC, VGA
ManualYes
Quick start guideYes
Warranty cardYes
Storage
Card reader integratedNo
Optical disc player typeNot included
Display
Built-in display-
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the BenQ MH606 below.

What is the weight of the BenQ MH606?

The BenQ MH606 has a weight of 2300 g.

What is the height of the BenQ MH606?

The BenQ MH606 has a height of 120 mm.

What is the width of the BenQ MH606?

The BenQ MH606 has a width of 296 mm.

What is the depth of the BenQ MH606?

The BenQ MH606 has a depth of 221 mm.

Is the manual of the BenQ MH606 available in English?

Yes, the manual of the BenQ MH606 is available in English .

Is your question not listed? Ask your question here

No results