BenQ MH606 manual

BenQ MH606
5.1 · 1
PDF manual
 · 48 pages
English
manualBenQ MH606
20 Operation

Operation

Starting up the projector

1. Plug the power cord. Turn on the power outlet switch
(where fitted). The power indicator on the projector
lights orange after power has been applied.
2. Press on the projector or on the remote
control to start the projector. The power indicator
flashes green and stays green when the projector is on.
The start up procedure takes about 30 seconds. In the
later stage of start up, a startup logo is projected.
(If necessary) Rotate the focus ring to adjust the image
clearness.
3. If the projector is activated for the first time, select your
OSD language following the on-screen instructions.
4. If you are prompted for a password, press the arrow keys
to enter a 6-digit password. See Utilizing the password
function on page 23.
5. Switch all of the connected equipment on.
6. The projector will search for input signals. The current
input signal being scanned appears. If the projector does
not detect a valid signal, the message “No Signal” will
continue displaying until an input signal is found.
You can also press SOURCE to select your desired input signal. See Switching input signal on page
24.
• Please use the original accessories (e.g. power cord) to avoid possible dangers such as electric shock and fire.
• If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before
energizing the lamp.
• The Setup Wizard screenshots are for reference only and may differ from the actual design.
• If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message
“Out of Range” displayed on the background screen. Please change to an input signal which is compatible with
the projector's resolution or set the input signal to a lower setting. See Timing chart on page 45.
• If no signal is detected for 3 minutes, the projector automatically enters saving mode.

Manual

View the manual for the BenQ MH606 here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 5.1. This manual is available in the following languages: English. Do you have a question about the BenQ MH606 or do you need help? Ask your question here

Need help?

Do you have a question about the BenQ and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

BenQ MH606 specifications

Below you will find the product specifications and the manual specifications of the BenQ MH606.

General
BrandBenQ
ModelMH606 | 9H.JGX77.13E
Productvideo projector
EAN4718755069925
LanguageEnglish
FiletypeUser manual (PDF)
Network
Wi-Fi-
Ethernet LAN (RJ-45) ports0
Ethernet LANNo
Projector
Projector brightness3500 ANSI lumens
Contrast ratio (typical)10000:1
Projection technologyDLP
Projector native resolution1080p (1920x1080)
Number of colors1.073 billion colors
Native aspect ratio16:9
Keystone correction, vertical-40 - 40 °
Screen size compatibility30 - 300 "
Horizontal scan range15 - 102 kHz
Vertical scan range23 - 120 Hz
Projection distance- m
Video
Full HDYes
Supported graphics resolutions640 x 480 (VGA), 1920 x 1080 (HD 1080), 1920 x 1200 (WUXGA)
Supported video modes480i, 480p, 576i, 576p, 720p, 1080i, 1080p
3DYes
Analog signal format systemNTSC, PAL, SECAM
Supported 3D formatsFrame Sequential, Frame packing, Side by side, Top and bottom
Light source
Lamp power200 W
Lamps quantity1 lamp(s)
Service life of light source5000 h
Service life of light source (economic mode)15000 h
Lamp typeUHP
Light source typeLamp
Lens system
Throw ratio1.49 - 1.64:1
Zoom ratio1.1:1
Focal length range22 - 24.1 mm
Aperture range (F-F)2.56 - 2.68
Offset108 %
Design
Product colorWhite
Product typeStandard throw projector
Market positioningBusiness
PlacementDesktop
Multimedia
Built-in speaker(s)Yes
RMS rated power2 W
Number of built-in speakers1
Image formats supportedJPG
Ports & interfaces
VGA (D-Sub) ports quantity2
S-Video inputs quantity1
Composite video in1
HDMI ports quantity2
DVI portNo
USB 2.0 ports quantity2
Audio (L/R) in0
Headphone outputs1
Microphone inYes
Serial interface typeRS-232
CardBus PCMCIA slot typeNo
Component video (YPbPr/YCbCr) in0
AC (power) inYes
Mobile High-Definition Link (MHL)Yes
Other features
RS-232 ports1
Power
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power sourceAC
Power consumption (typical)260 W
Power consumption (standby)0.5 W
Auto power offYes
Features
Noise level32 dB
Noise level (economic mode)29 dB
On Screen Display (OSD)Yes
On Screen Display (OSD) languagesARA, BUL, CHI (SIMPL), CHI (TR), CRO, CZE, DAN, DEU, DUT, ENG, ESP, FIN, FRE, GRE, HUN, IND, ITA, JPN, KOR, NOR, POL, POR, RUM, RUS, SWE, THA, TUR
Operational conditions
Operating temperature (T-T)0 - 40 °C
Weight & dimensions
Width296 mm
Depth221 mm
Height120 mm
Weight2300 g
Packaging content
Handheld remote controlYes
Remote control typeIR
Cables includedAC, VGA
ManualYes
Quick start guideYes
Warranty cardYes
Storage
Card reader integratedNo
Optical disc player typeNot included
Display
Built-in display-
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the BenQ MH606 below.

What is the weight of the BenQ MH606?

The BenQ MH606 has a weight of 2300 g.

What is the height of the BenQ MH606?

The BenQ MH606 has a height of 120 mm.

What is the width of the BenQ MH606?

The BenQ MH606 has a width of 296 mm.

What is the depth of the BenQ MH606?

The BenQ MH606 has a depth of 221 mm.

Is the manual of the BenQ MH606 available in English?

Yes, the manual of the BenQ MH606 is available in English .

Is your question not listed? Ask your question here

No results