BenQ MH535 manual

BenQ MH535
5.1 · 1
PDF manual
 · 73 pages
English
manualBenQ MH535
Operation 27
3. If the projector is activated for the first
time, select your OSD language following
the on-screen instructions.
4. If you are prompted for a password, press
the arrow keys to enter a six digit
password. See "Utilizing the password
function" on page 31 for details.
5. Switch all of the connected equipment on.
6. The projector will start to search for input
signals. The current input signal being
scanned displays in the screen. If the
projector doesn't detect a valid signal, the
message 'No Signal' will continue
displaying until an input signal is found.
You can also press Source on the projector or remote control to select your
desired input signal. See "Switching input signal" on page 33 for details.
If no signal is detected for 3 minutes, the projector automatically enters
ECO BLANK mode.

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 front adjuster foot and 2 rear adjuster feet. These
adjusters change the image height and projection angle. To adjust the projector:
1. Pull the quick-release lever and lift the front
of the projector. Once the image is
positioned where you want it, release the
quick-release lever to lock the foot in
position. You may also screw the front
adjuster foot to change the image height.
2. Screw the rear adjuster feet to fine tune the
horizontal angle.
If the projector is not placed on a flat surface or
the screen and the projector are not
perpendicular to each other, the projected image becomes trapezoidal. To correct
this situation, see "Magnifying and searching for details" on page 34 for details.
Do not look into the lens while the lamp is on. The strong light from the
lamp may cause damage to your eyes.
Be careful when you press the adjuster button as it is close to the
exhaust vent where hot air comes from.

Manual

View the manual for the BenQ MH535 here, for free. This manual comes under the category video projectors and has been rated by 1 people with an average of a 5.1. This manual is available in the following languages: English. Do you have a question about the BenQ MH535 or do you need help? Ask your question here

Index

Need help?

Do you have a question about the BenQ and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

BenQ MH535 specifications

Below you will find the product specifications and the manual specifications of the BenQ MH535.

General
BrandBenQ
ModelMH535 | 9H.JJY77.33E
Productvideo projector
EAN4718755075797
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF)
Projector
Projector brightness3500 ANSI lumens
Horizontal scan range15 - 102 kHz
Vertical scan range23 - 120 Hz
Screen size compatibility30 - 300 "
Keystone correction, vertical-40 - 40 °
Native aspect ratio16:9
Projection technologyDLP
Projector native resolution1080p (1920x1080)
Contrast ratio (dynamic)15000:1
Contrast ratio (typical)-
Projection distance- m
Features
Number of OSD languages28
On Screen Display (OSD)Yes
Noise level32 dB
Noise level (economic mode)29 dB
Packaging content
Handheld remote controlYes
Batteries includedYes
Cables includedAC, VGA
ManualYes
Quick start guideYes
Warranty cardYes
Weight & dimensions
Weight2420 g
Width332.4 mm
Depth241.3 mm
Height99 mm
Power
Power sourceAC
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (typical)252 W
Power consumption (standby)0.5 W
Operational conditions
Operating temperature (T-T)0 - 40 °C
Storage temperature (T-T)-20 - 60 °C
Operating relative humidity (H-H)10 - 90 %
Storage relative humidity (H-H)10 - 90 %
Operating altitude0 - 1499 m
Video
Analog signal format systemNTSC, PAL, SECAM
Supported video modes480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Full HDYes
3D-
Supported graphics resolutions640 x 480 (VGA), 1920 x 1080 (HD 1080), 1920 x 1200 (WUXGA)
Other features
RS-232 ports1
Ports & interfaces
PC Audio inYes
PC Audio outYes
Mini-USB 2.0 ports quantity1
HDMI ports quantity2
HDMI connector typeFull-size
HDMI version1.4a
Composite video in1
S-Video inputs quantity1
VGA (D-Sub) ports quantity3
Component video (YPbPr/YCbCr) in0
DVI portNo
USB 2.0 ports quantity0
Audio (L/R) in0
AC (power) inYes
Serial interface typeRS-232
Network
Ethernet LAN (RJ-45) ports0
Smart TVNo
Wi-FiNo
Ethernet LANNo
Multimedia
Built-in speaker(s)Yes
Number of built-in speakers1
RMS rated power2 W
Lens system
Offset107 %
Focal length range19 - 22.65 mm
Aperture range (F-F)2.42 - 2.62
Zoom capabilityYes
Zoom ratio1.2:1
Throw ratio1.37 - 1.64:1
Light source
Service life of light source5000 h
Service life of light source (economic mode)10000 h
Lamp power203 W
Lamps quantity1 lamp(s)
Light source typeLamp
Design
Cable lock slotYes
Cable lock slot typeKensington
Product typeStandard throw projector
Product colorWhite
Market positioningBusiness
PlacementDesktop, Ceiling
Display
Built-in displayNo
Storage
Card reader integratedNo
Logistics data
Harmonized System (HS) code85286200
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the BenQ MH535 below.

What is the weight of the BenQ MH535?

The BenQ MH535 has a weight of 2420 g.

What is the height of the BenQ MH535?

The BenQ MH535 has a height of 99 mm.

What is the width of the BenQ MH535?

The BenQ MH535 has a width of 332.4 mm.

What is the depth of the BenQ MH535?

The BenQ MH535 has a depth of 241.3 mm.

Is the manual of the BenQ MH535 available in English?

Yes, the manual of the BenQ MH535 is available in English .

Is your question not listed? Ask your question here

No results