Behringer HC 2000B manual

Behringer HC 2000B
7.5 · 1
PDF manual
 · 4 pages
English
manualBehringer HC 2000B

Getting started

Power Supply

The unit is powered by a built-in, lithium-polymer rechargeable
battery. Charge the built-in battery for at least four hours before
using the device for the  rst time.
To charge the internal battery, follow these steps:
1. Connect the smaller end of the supplied USB cable to the
MICRO USB jack.
2. Connect the other end to a powered USB jack on your computer
or an AC power supply (not included).
3. The CHARGE LED indicator will change color to red
during charging.
4. When fully charged, the CHARGE LED indicator will turn blue.

Warnings:

Do not throw batteries in  re!
While using the built-in battery, the environmental
temperature should be 5° C (41° F) to 35° C (95° F).
To get the longest service life for the built-in battery, charge at
room temperature.
Attention should be drawn the environmental aspects of
battery disposal.
Battery shall not be exposed to excessive heat such as
sunshine,  re or the like.
When the battery is low, the unit will beep every 20 seconds.
The unit will turn o automatically when the battery is too low
to work.

Turning the unit on/o

1. Long press the POWER button to turn ON the unit. The
BLUETOOTH LED indicator will light on.
2. Long press the POWER button again turn OFF the unit. The
BLUETOOTH LED indicator will turn o .

Bluetooth pairing

1. Long press to turn ON the unit. The BLUETOOTH LED indicator
will blink blue and red alternately to indicate the unit is in
pairing mode.
2. On the Bluetooth device, enable Bluetooth and select “HC
2000B” from the Device List. (Refer to the user manual of your
Bluetooth device for detailed operations.)
3. If the Bluetooth device prompts for a passcode, use “0000”.
Some Bluetooth devices will ask you to accept and con rm the
connection. If the units are paired properly, you will hear an
indication sound. If pairing is not successful within 10 minutes,
the headphones will turn o automatically.
NOTE: If you want to connect your headphones to another
Bluetooth audio device, you need to disconnect the current device
rst and follow the above steps to make a new connection.

Using A Bluetooth Device

1. When successfully paired, sound from your Bluetooth device
will be audible through the headphones
2. Press the PLAY/PAUSE button to pause playback. Press again to
resume playback.
3. Short press the FORWARD/BACK buttons to adjust the
headphone volume. You can also adjust the volume directly on
your paired Bluetooth device.
4. Long press the FORWARD/BACK buttons to select your desired
audio  le.
NOTE: The BLUETOOTH LED indicator will blink blue
during playback.

Receiving A Phone Call

These headphones are equipped with a built-in microphone, which
allows you to make calls on a Bluetooth-enabled mobile phone.
Make sure your Bluetooth-enabled mobile phone is paired with the
headphones. When a call comes in to the connected mobile phone,
you will hear an incoming call alert on the headphones.
1. Press the FORWARD button to answer the incoming call.
2. Press the FORWARD button again to end the call.
3. The reject the incoming call, press and hold the BACK button.
4. To transfer the sound between the headphones and the mobile
phone, press and hold the PLAY/PAUSE button during the call.

Manual

View the manual for the Behringer HC 2000B here, for free. This manual comes under the category Headset and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Behringer HC 2000B or do you need help? Ask your question here

Need help?

Do you have a question about the Behringer HC 2000B and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Behringer HC 2000B owners to provide you with a good answer.

Number of questions: 0

Behringer HC 2000B specifications

Below you will find the product specifications and the manual specifications of the Behringer HC 2000B.

Get the thin device you want without sacrificing battery life. The lithium polymer battery delivers the same long-lastin...
General
Brand Behringer
Model HC 2000B | HC 2000B
Product Headset
EAN 4033653120586
Language English
Filetype Usermanual (PDF)
Performance
Product colour Black
Product type Headset
Wearing style Head-band
Recommended usage Stage/Studio
Headset type Binaural
Operating keys Play/pause,Track <,Track >,Volume +,Volume -
Volume control Button
LED indicators Bluetooth,Status
Certification FCC
Ports & interfaces
Connectivity technology Wireless
Bluetooth
USB connectivity
USB connector Micro-USB
3.5 mm connector
Bluetooth version 5.0
Frequency band 2.4 - 2.48 GHz
Wireless range 10 m
Headphones
Ear coupling Circumaural
Headphone frequency 20 - 20000 Hz
Impedance - Ω
Acoustic system Closed
Battery
Battery operated
Battery type Built-in battery
Battery technology Lithium Polymer (LiPo)
Battery capacity 185 mAh
Battery voltage 3.7 V
Battery life (max) 7 h
Battery recharge time 3 h
Microphone
Microphone type Built-in
Packaging content
Quantity 1
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Behringer HC 2000B below.

Is your question not listed? Ask your question here

No results