View the manual for the BeamZ S1500 160.492 here, for free. This manual comes under the category knifes and has been rated by 4 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the BeamZ S1500 160.492 or do you need help? Ask your question here




| Brand | BeamZ |
| Model | S1500 160.492 | 160.492 |
| Product | knife |
| EAN | 8715693263985, 1983546342638 |
| Language | English |
| Filetype | User manual (PDF) |
| Power | 1500 W |
| AC input voltage | 220-240 V |
| AC input frequency | 50 Hz |
| Liquid tank capacity | 2 L |
| Cable length | 3 m |
| Remote control type | Wired |
| Remotely operated | Yes |
| Smoke output volume | 295 m³/min |
| Heating time | 8 min |
| Product color | Black, Grey |
| Operating fluid | Water |
| Product dimensions (WxHxD) | 470 x 250 x 190 mm |
| Weight | 5600 g |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the BeamZ S1500 160.492 below.
The BeamZ S1500 160.492 has a weight of 5600 g.
The power of the BeamZ S1500 160.492 is 1500 W. This high power ensures a strong and efficient performance, making it a reliable choice for users.
The BeamZ S1500 160.492 has a liquid tank capacity of 2 L. This generous capacity allows for longer operating times without frequent refills.
The BeamZ S1500 160.492 comes with a wired remote control. This offers a convenient and reliable way for users to operate the device without the need for direct access to it.
Yes, the BeamZ S1500 160.492 can be operated remotely. This feature enhances user convenience and allows for easy control of the smoke output from a distance.
The BeamZ S1500 160.492 has a smoke output volume of 295 m³/min. This high volume ensures a dense and impressive smoke effect, making it ideal for various events and performances.
To troubleshoot if the smoke level control is not working properly for the BeamZ S1500 160.492 knife, follow these steps: 1. Check the working temperature: If the smoke level control is not functioning correctly, it may be due to the thermostat switching off. Wait a few minutes for the fog generator to cool down and reach the working temperature again. To maintain the temperature, try producing smoke with small pauses in between. 2. Verify the power supply: Ensure that the knife is properly plugged into a power source. If the unit is not receiving sufficient power, it may affect the smoke level control. 3. Check the DMX control: If the knife is connected to a DMX controller or a DMX loop, make sure the DMX connection is secure. Use a 3-pin XLR connector for the DMX connection. Additionally, check the DIP switch on the rear panel to set the correct start address for the DMX control. 4. Clean the smoke machine: If the smoke level control is still not working, it may be necessary to clean the smoke machine. After 40 hours of use, deposits can accumulate and affect the performance. Follow the cleaning procedure mentioned in the manual, ensuring the machine is in a well-ventilated area. 5. Contact customer support: If the above steps do not resolve the issue, it is recommended to contact BeamZ customer support for further assistance and troubleshooting guidance. Please note that these troubleshooting steps are based on the information provided and may vary depending on the specific issue encountered.
To troubleshoot if the DMX loop is not transmitting data correctly for the BeamZ S1500 160.492 knife, follow these steps: 1. Check the DMX connection: Ensure that the knife is properly connected to a DMX controller or a DMX loop with multiple DMX effects. Use a 3-pin XLR connector for the DMX connection. 2. Set the start address: Verify that the DIP switches on the rear panel of the knife are set to the correct start address. The start address is defined as the first channel where the knife responds. Make sure there are no overlapping channels used. 3. Use a 120 Ohm terminator: It is necessary to always terminate the DMX loop with a 120 Ohm terminator for proper data transmission. Check that the DMX loop is properly terminated. 4. Check for overlapping channels: Ensure that no overlapping channels are used in the DMX setup. Overlapping channels can cause data transmission issues. Adjust the channel assignments if necessary. 5. Contact customer support: If the above steps do not resolve the issue, it is recommended to contact BeamZ customer support for further assistance and troubleshooting guidance. Please note that these troubleshooting steps are provided as a general guide and may vary depending on the specific issue encountered.
To troubleshoot if the fluid reservoir of the BeamZ S1500 160.492 knife is not refilling properly, follow these steps: 1. Ensure safety: Before refilling the fluid reservoir, make sure to unplug the knife from the power source to prevent any accidents or damage. 2. Use the original BeamZ smoke liquid: It is important to use only the original BeamZ smoke liquid for refilling. This smoke liquid is environmentally friendly, biodegradable, and leaves no residue when used correctly. 3. Remove the reservoir cap: Unscrew the cap of the reservoir carefully to access the refill opening. 4. Fill the reservoir: Use a suitable funnel to pour the smoke liquid into the reservoir. Be cautious not to overfill the reservoir and avoid any spillage. 5. Close the reservoir cap: After refilling, securely close the cap of the reservoir to prevent any leakage or contamination. Please note that these steps are provided as a general guide and may vary slightly depending on the specific instructions provided in the manual for the BeamZ S1500 160.492 knife.
To effectively clean the smoke machine of the BeamZ S1500 160.492 knife, follow these steps: 1. Turn off and unplug the knife: Before cleaning the smoke machine, ensure that the knife is turned off and unplugged from the power source to prevent any accidents or damage. 2. Remove the fluid reservoir: Unscrew the cap of the fluid reservoir and carefully remove it from the knife. Empty any remaining smoke liquid from the reservoir. 3. Clean the reservoir: Rinse the reservoir with warm water to remove any residue or buildup. Use a soft brush or cloth to gently scrub the interior of the reservoir. Avoid using harsh chemicals or abrasive materials that may damage the reservoir. 4. Clean the nozzle: Locate the nozzle of the smoke machine and inspect it for any clogs or blockages. Use a small brush or cotton swab dipped in warm water to clean the nozzle. Ensure that the nozzle is completely clear and free from any debris. 5. Reassemble and test: Once the reservoir and nozzle are clean, reassemble the smoke machine by securely attaching the reservoir and tightening the cap. Plug in the knife and turn it on to test the smoke production. If the cleaning was successful, the smoke machine should now function effectively. Please note that these steps are provided as a general guide and may vary slightly depending on the specific instructions provided in the manual for the BeamZ S1500 160.492 knife.
To troubleshoot if the smoke production of the BeamZ S1500 160.492 knife is not meeting the expected level, follow these steps: 1. Check the working temperature: The fog generator of the knife is designed to cool down after a certain period of time to prevent overheating. Wait a few minutes until the working temperature is reached again. To maintain the temperature, try producing smoke with small pauses in between. 2. Verify the smoke fluid level: Ensure that the smoke fluid reservoir is adequately filled. If the fluid level is low, it can affect the smoke production. Refill the reservoir with the recommended BeamZ smoke fluid. 3. Clean the nozzle: Inspect the nozzle of the smoke machine for any clogs or blockages. Use a small brush or cotton swab dipped in warm water to clean the nozzle. Ensure that the nozzle is clear and free from any debris. 4. Check the power supply: Ensure that the knife is properly plugged into a power source. Insufficient power supply can affect the smoke production. Check the power cable and connections. 5. Contact customer support: If the above steps do not resolve the issue, it is recommended to contact BeamZ customer support for further assistance and troubleshooting guidance. Please note that these steps are provided as a general guide and may vary depending on the specific instructions provided in the manual for the BeamZ S1500 160.492 knife.
To troubleshoot if the smoke level control of the BeamZ S1500 160.492 knife is not working properly, you can follow these steps: 1. Check the working temperature: If the smoke level control is not functioning correctly, it may be due to the knife being cooled down too much. Wait a few minutes for the knife to reach the working temperature again. It is recommended to produce smoke with small pauses in between to maintain the temperature and prevent the thermostat from switching off. 2. Verify the power supply: Ensure that the knife is properly connected to a power source. Check if the power supply is stable and providing the required voltage (220-240V~/50Hz). 3. Inspect the smoke liquid: Make sure you are using the original Beamz smoke liquid and that it is not contaminated. Contaminated smoke liquid can affect the smoke level control. Close the cap of the liquid smoke can tightly to prevent contamination. 4. Clean the knife: After 40 hours of use, it is important to clean the knife to avoid deposits. Follow the cleaning procedure mentioned in the manual, which involves removing the smoke liquid, adding a cleaning solution, running the machine to pump the solution through, and refilling the tank with liquid smoke. By following these troubleshooting steps, you should be able to identify and resolve any issues with the smoke level control of the BeamZ S1500 160.492 knife.
To troubleshoot if the DMX loop of the BeamZ S1500 160.492 knife is not transmitting data correctly, you can follow these steps: 1. Check the DMX connection: Ensure that the DMX cable is securely connected to both the knife and the DMX controller or other DMX effects in the loop. Make sure the cable is not damaged or loose. 2. Verify the DMX address: Use the DIP switches located on the back of the knife to set the DMX address. The base address is defined as the first channel where the knife responds. Ensure that there are no overlapping channels used. 3. Confirm termination: It is necessary to always terminate the DMX loop with a 120 Ohm terminator for proper data transmission. Check if the loop is properly terminated. 4. Test with a different DMX cable: If the DMX loop is still not transmitting data correctly, try using a different DMX cable to rule out any cable issues. 5. Check the DMX controller: Test the DMX controller with another DMX device to ensure that the issue is specific to the knife. If the other device works properly, the problem may lie within the knife itself. By following these troubleshooting steps, you should be able to identify and resolve any issues with the DMX loop data transmission of the BeamZ S1500 160.492 knife.
To troubleshoot if the fluid reservoir of the BeamZ S1500 160.492 knife is not refilling properly, you can follow these steps: 1. Ensure safety: Before refilling the fluid reservoir, always disconnect the knife from the power source by removing the plug from the mains. 2. Check the reservoir cap: Unscrew the cap of the reservoir and inspect it for any damage or debris. Clean the cap if necessary to ensure a proper seal. 3. Use original Beamz smoke liquid: Only use the original Beamz smoke liquid to refill the reservoir. This smoke liquid is environmentally friendly, biodegradable, and leaves no residue when used correctly. 4. Fill the reservoir carefully: Use a suitable funnel to fill the reservoir with the smoke liquid. Take care not to overfill the reservoir, as it may lead to leakage or improper functioning. 5. Close the cap tightly: After refilling the reservoir, close the cap tightly to prevent any contamination or leakage. If the fluid reservoir of the BeamZ S1500 160.492 knife still does not refill properly after following these steps, it is recommended to refer to the manual or contact the manufacturer for further assistance.
To troubleshoot if the smoke machine of the BeamZ S1500 160.492 knife is not producing enough smoke, you can follow these steps: 1. Check the working temperature: Ensure that the smoke machine has reached its working temperature before expecting optimal smoke production. It takes approximately 8 minutes for the machine to reach the working temperature. If the machine has cooled down, wait a few minutes for it to reach the working temperature again. 2. Use the correct smoke fluid: Only use the original Beamz smoke fluid that is environmentally friendly and leaves no residues when used correctly. Using other fluids may affect the smoke production. 3. Avoid overfilling the fluid tank: Fill the fluid tank with the smoke fluid using a funnel, but be careful not to overfill it. Overfilling can lead to leakage and affect the smoke production. Follow the instructions in the manual regarding the proper filling level. 4. Maintain pauses between smoke production: To maintain the working temperature and prevent the thermostat from switching off, it is recommended to produce smoke with small pauses in between. This allows the machine to maintain its temperature and ensures continuous smoke production. By following these troubleshooting steps, you should be able to improve the smoke production of the BeamZ S1500 160.492 knife.
To troubleshoot if the BeamZ S1500 160.492 knife is not heating up properly, you can follow these steps: 1. Check the working temperature: The knife needs to reach its working temperature for proper heating. Wait for a few minutes until the working temperature is reached again. It is recommended to produce smoke with small pauses in between to maintain the temperature and prevent the thermostat from switching off. 2. Verify the power supply: Ensure that the knife is properly connected to a stable power source. Check if the power supply is providing the required voltage (220-240V~/50Hz). 3. Allow warm-up time: After turning on the knife, it requires some warm-up time before it is ready for use. During this time, the LED indicator will light up. If the machine stops during use, the LED will go out, indicating that the machine is warming up. 4. Check for obstructions: Make sure there are no obstructions blocking the airflow or the heating element. Clear any debris or objects that may be hindering the proper heating of the knife. 5. Contact customer support: If the knife still does not heat up properly after following these steps, it is recommended to contact the manufacturer's customer support for further assistance. By following these troubleshooting steps, you should be able to identify and resolve any issues with the heating of the BeamZ S1500 160.492 knife.
Yes, the manual of the BeamZ S1500 160.492 is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the BeamZ and is the answer not in the manual?
Question and answer
Number of questions: 0