BeamZ Pandora 1250 TTL manual

BeamZ Pandora 1250 TTL
6.9 · 1
PDF manual
 · 16 pages
English
manualBeamZ Pandora 1250 TTL
2

ENGLISH

Congratulations to the purchase of this Beamz product. Please read this manual thoroughly prior to using the unit in
order to benefit fully from all features.
Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all
precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to
avoid electrical shock. Keep the manual for future reference.
- Prior to using the unit, please ask advice from a
specialist. When the unit is switched on for the first
time, some smell may occur. This is normal and will
disappear after a while.
- The unit contains voltage carrying parts. Therefore do
NOT open the housing.
- Do not place metal objects or pour liquids into the unit
This may cause electrical shock and malfunction.
- Do not place the unit near heat sources such as
radiators, etc. Do not place the unit on a vibrating
surface. Do not cover the ventilation holes.
- The unit is not suitable for continuous use.
- Be careful with the mains lead and do not damage it.
A faulty or damaged mains lead can cause electrical
shock and malfunction.
- When unplugging the unit from a mains outlet, always
pull the plug, never the lead.
- Do not plug or unplug the unit with wet hands.
- If the plug and/or the mains lead are damaged, they
need to be replaced by a qualified technician.
- If the unit is damaged to such an extent that internal
parts are visible, do NOT plug the unit into a mains
outlet and DO NOT switch the unit on. Contact your
dealer. Do NOT connect the unit to a rheostat or
dimmer.
- To avoid fire and shock hazard, do not expose the
unit to rain and moisture.
- All repairs should be carried out by a qualified
technician only.
- Connect the unit to an earthed mains outlet (220-
240Vac/50Hz) protected by a 10-16A fuse.
- During a thunderstorm or if the unit will not be used
for a longer period of time, unplug it from the mains.
The rule is: Unplug it from the mains when not in use.
- If the unit has not been used for a longer period of
time, condensation may occur. Let the unit reach
room temperature before you switch it on. Never use
the unit in humid rooms or outdoors.
- During operation, the housing becomes very hot. Do
not touch it during operation and immediately after.
- To prevent accidents in companies, you must follow
the applicable guide lines and follow the instructions.
- Secure the unit with an extra safety chain if the unit is
ceiling mount. Use a truss system with clamps. Make
sure nobody stands in the mounting area. Mount the
effect at least 50cm away from inflammable material
and leave at least 1 meter space on every side to
ensure sufficient cooling.
- This unit contains high intensity LEDs. Do not look
into the LED light to prevent damage to your eyes.
- Do not repeatedly switch the fixture on and off. This
shortens the life time.
- Keep the unit out of the reach of children. Do not
leave the unit unattended.
- Do not use cleaning sprays to clean switches. The
residues of these sprays cause deposits of dust and
grease. In case of malfunction, always seek advice
from a specialist.
- Only operate the unit with clean hands.
- Do not force the controls.
- If the unit has fallen, always have it checked by a
qualified technician before you switch the unit on
again.
- Do not use chemicals to clean the unit. They damage
the varnish. Only clean the unit with a dry cloth.
- Keep away from electronic equipment that may cause
interference.
- Only use original spares for repairs, otherwise
serious damage and/or dangerous radiation may
occur.
- Switch the unit off prior to unplugging it from the
mains and/or other equipment. Unplug all leads and
cables prior to moving the unit.
- Make sure that the mains lead cannot be damaged
when people walk on it. Check the mains lead before
every use for damages and faults!
- The mains voltage is 220-240Vac/50Hz. Check if
power outlet match. If you travel, make sure that the
mains voltage of the country is suitable for this unit.
- Keep the original packing material so that you can
transport the unit in safe conditions
This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficient
magnitude to cause a shock hazard.
This mark attracts the attention of the user to important instructions that are contained in the manual and that he should
read and adhere to.
DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacks
should be aware of the effects that this light effect may have on them.
The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate and
their guarantee!
NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and
35°C/95°F.
Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your
local authorities or your dealer about the way to proceed.

View the manual for the BeamZ Pandora 1250 TTL here, for free. This manual comes under the category Effect machines and has been rated by 1 people with an average of a 6.9. This manual is available in the following languages: English. Do you have a question about the BeamZ Pandora 1250 TTL or do you need help? Ask your question here

Need help?

Do you have a question about the BeamZ and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other BeamZ owners to provide you with a good answer.

Number of questions: 0

General
BeamZ
Pandora 1250 TTL | 152.988
Effect machine
8715693274929
English
User manual (PDF)
Design
Product colourBlack
Built-in display
Product typeDisco stroboscope
CertificationCE
Suitable for indoor use
Lamps
Laser wave power (red)300 mW
Laser wavelength (red)635 nm
Laser wave power (green)200 mW
Laser wavelength (green)532 nm
Laser class4
Number of colours7 colours
Light colourBlue, Green, Red
Features
Lighting control protocolsDMX
DMX channels quantity12 channels
Adjustable sensitivity
Adjustable speed
Lighting modesSound activated
Weight & dimensions
Weight4750 g
Depth235 mm
Height172 mm
Width220 mm
Ball diameter- "
Power
Power consumption (typical)80 W
Power sourceAC
Input voltage220 - 240 V
Input frequency50 Hz
Packaging content
Remote control included
Cables includedAC
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the BeamZ Pandora 1250 TTL below.

Is your question not listed? Ask your question here

No results