Barska AX11620 manual

Barska AX11620
(1)
  • Number of pages: 2
  • Filetype: PDF

User’s Manual for Biometric Safe

A. Initialization Button
B. Battery Compartment
C. Bolts
D. Fingerprint Scanner
E. Indicator Lights
F
G
A
B
D
E
H
* Actual model may vary
See reverse side for more information
9/12
BC248

1. INSTALL BATTERIES

1. Remove Battery Compartment (B) cover
2. Insert 4 AA batteries and restore battery cover
3. Bolts (C) automatically extend when batteries are inserted
To retract bolts:
- Press and release Wake-Up Button (F)
- Place any finger on the Fingerprint Scanner (D)
- Bolts will retract

2. FINGERPRINT REGISTRATION

IMPORTANT:
The safe is in Factory Default mode, ANY fingerprint can
open the safe. Only successful registered fingerprint can
terminate Factory Default mode
During registration the door must remain open and the Bolts (C)
must be in the retracted position. Otherwise, the fingerprint will
not be saved
To retract bolts:
- Press and release Wake-Up Button (F)
- Place any finger on Fingerprint Scanner (D)
- Bolts will retract
1. Press and release Initialization Button (A)
2. Immediately place a finger on the Fingerprint Scanner (D)
- Hold finger still
- 1 beep will be heard recognizing the fingerprint; followed by
2 consecutive beeps
- Remove finger
- Registration is complete
Successful Registration
Registration is successful when a total of 3 beeps are heard
Unsuccessful Registration
2 short beeps will be heard; repeat registration process again
3. To register another fingerprint – repeat steps 1 - 2

3. TEST A REGISTERED FINGERPRINT

1. With safe door open, press and release Wake-Up Button (F)
- Bolts (C) will extend
2. Press and release Wake-Up Button (F)
- Place a non-registered finger on the Fingerprint Scanner (D)
- Bolts will stay extended
3. If the bolts retract with a non-registered fingerprint,
registration was unsuccessful; and safe remains in Factory
Default mode
- Repeat steps under FINGERPRINT REGISTRATION
4. Press and release Wake-Up Button (F)
- Place a registered finger on the Fingerprint Scanner (D)
- Bolts will retract

4. CLOSE/OPEN SAFE DOOR

CLOSE: Close door, press and release Wake-Up Button (F)
- Bolts will extend
OPEN: Press and release Wake-Up Button (F)
- Place a registered finger on Fingerprint Scanner (D)
- Bolts will retract

5. BEEP SOUND OPTIONS

Beep OFF: Press and HOLD the Initialization Button (A) until
the Indicator Lights (E) are flashing green – RELEASE the
Initialization Button
Beep ON: Press and HOLD the Initialization Button (A) until
the Indicator Lights (E) are flashing green followed by 1 beep
– RELEASE the Initialization Button

6. DOOR OPEN ALARM

Regardless of the beep sound option chosen (either On or Off)
the door alarm is fixed to beep
The alarm is activated when the safe door is open and Bolts
(C) are retracted
Within 5 seconds, the Indicator Lights (E) will start to
flash green
More than 5 minutes, the safe will start beeping every
10-20 seconds
Close safe door, press and release Wake-Up Button (F) to
extend the Bolts (C) to cease the alarm
With the safe door open and the Bolts (C) extended, no lights
or beeping will be heard

7. OPEN SAFE WITH EMERGENCY KEY

1. To expose the Emergency Key access, remove Logo
Plate (G) screws with provided Allen wrench
2. Insert Emergency Key into key access, and turn clockwise
to open
NOTE: Store Emergency Keys in a secure place, NOT inside
of the safe
C
F. Wake-Up Button
G. Logo Plate and Emergency
Key Access
H. External Battery Access
(optional)

WARNING

- New Safe is in Factory Default mode, ANY fingerprint

can open the safe. Only successful registered

fingerprint can terminate Factory Default mode.

- Register at least two different fingerprints and test a

few times before closing the safe door.

- Test with a non-registered fingerprint. If the safe

opens, the safe remains in Factory Default mode.

- Avoid leaving safe door open and unattended; it will

allow unauthorized individuals to add their fingerprints

and/or reprogram the safe, gaining full access to the

safe and the contents.

- Test the Emergency Keys and store them in a secure

place, NOT inside of the safe.

- To maximize the security and performance of the

safe, test registered fingerprints every 6 months.

Read all instructions before using this safe.

Barska AX11620

Need help?

Number of questions: 1

Do you have a question about the Barska AX11620 or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Barska AX11620 owners to properly answer your question.

Arie Foster, 30-9-2019 18:26:02 No comments

Battery is N/G..and NO key...any ideas? it still beeps and flashes red..wont read print

Answer this question

View the manual for the Barska AX11620 here, for free. This manual comes under the category Safes and has been rated by 1 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the Barska AX11620 or do you need help? Ask your question here

Barska AX11620 specifications

General
Brand Barska
Model AX11620
Product Safe
Language English
Filetype PDF
Features
Material Steel
Product colour Black
Lock type Electronic
Number of bolts 2
Quantity 1
Power
Power source type Battery
Weight & dimensions
Width 198.12 mm
Depth 198.12 mm
Height 299.72 mm
Interior dimensions (W x D x H) 193.04 x 149.86 x 294.64 mm
Door thickness 4.7625 mm
Weight 5443 g
show more

Frequently Asked Questions

Below, you will find the most frequently asked questions about the Barska AX11620.

Is your question not listed? Ask your question here