Axis P3717-PLE manual

Axis P3717-PLE
7.8 · 1
PDF manual
 · 20 pages
English
manualAxis P3717-PLE

AXIS P3717–PLE Network Camera

Troubleshooting

2. Log in to the product as an administrator.
3. Go to Settings > System > Maintenance. Follow the instructions on the page. When the upgrade has nished, the
product restarts automatically.
AXIS Device Manager can be used for multiple upgrades. Find out more at axis.com/products/axis-device-manager

Technical issues, clues and solutions

If you can’t nd what you’re looking for here, try the troubleshooting section at axis.com/support
Problems upgrading the rmware
Firmware upgrade failure If the rmware upgrade fails, the product reloads the previous rmware. The most common reason
is that the wrong rmware le has been uploaded. Check that the name of the rmware le
corresponds to your product and try again.
Problems after rmware
upgrade
If you experience problems after a rmware upgrade, roll back to the previously installed version
from the Maintenance page.
Problems setting the IP address
The product is located on a
different subnet
If the IP address intended for the product and the IP address of the computer used to access the
product are located on different subnets, you cannot set the IP address. Contact your network
administrator to obtain an IP address.
The IP address is being used
by another device
Disconnect the Axis product from the network. Run the ping command (in a Command/DOS
window, type ping and the IP address of the product):
If you receive: Reply from <IP address>: bytes=32; time=10...
this means that the IP address may already be in use by another device on the network.
Obtain a new IP address from the network administrator and reinstall the product.
If you receive: Request timed out, this means that the IP address is available
for use with the Axis product. Check all cabling and reinstall the product.
Possible IP address conict
with another device on the
same subnet
The static IP address in the Axis product is used before the DHCP server sets a dynamic address.
This means that if the same default static IP address is also used by another device, there may
be problems accessing the product.
The product cannot be accessed from a browser
Cannot log in
When HTTPS is enabled, ensure that the correct protocol (HTTP or HTTPS) is used when attempting
to log in. You may need to manually type http or https in the browser’s address eld.
If the password for the user root is lost, the product must be reset to the factory default settings.
See How to reset to factory default settings on page 15.
The IP address has been
changed by DHCP
IP addresses obtained from a DHCP server are dynamic and may change. If the IP address has been
changed, use AXIS IP Utility or AXIS Device Manager to locate the product on the network. Identify
the product using its model or serial number, or by the DNS name (if the name has been congured).
If required, a static IP address can be assigned manually. For instructions, go to axis.com/support
The product is accessible locally but not externally
Router conguration
Check that your router allows incoming data trafc to the Axis product. The router must support
UPnP
®
.
Firewall protection
Check the Internet rewall with your network administrator.
16

Manual

View the manual for the Axis P3717-PLE here, for free. This manual comes under the category security cameras and has been rated by 1 people with an average of a 7.8. This manual is available in the following languages: English. Do you have a question about the Axis P3717-PLE or do you need help? Ask your question here

Need help?

Do you have a question about the Axis and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Axis P3717-PLE specifications

Below you will find the product specifications and the manual specifications of the Axis P3717-PLE.

General
BrandAxis
ModelP3717-PLE | P3717-PLE
Productsecurity camera
LanguageEnglish
FiletypeUser manual (PDF)
Performance
TypeIP security camera
Placement supported-
Connectivity technologyWired & Wireless
Network
Ethernet LANYes
Wi-Fi-
Bluetooth-
Design
Form factorBox
Product colorBlack, White
Mounting typeWall
Video
Maximum resolution- pixels
Total megapixels- MP
Camera
Minimum illumination- lx
Image sensor
Sensor typeCMOS
Number of sensors-
Storage
Built-in HDD-
Night vision
Night visionYes
Packaging content
Number of cameras1
Power
Power source type-
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Axis P3717-PLE below.

What is a megapixel?

The number of megapixels denotes how many pixels there are in the sensor. 1 megapixel equals 1 million pixels. The more pixels, the higher the potential image quality.

What does the abbreviation 'MP' stand for?

MP stands for MegaPixels.

Is the manual of the Axis P3717-PLE available in English?

Yes, the manual of the Axis P3717-PLE is available in English .

Is your question not listed? Ask your question here

No results