Audio-Technica AT2035 manual

Audio-Technica AT2035
6.3 · 1
PDF manual
 · 2 pages
English
manualAudio-Technica AT2035

AT2035

Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
©2010 Audio-Technica U.S., Inc. audio-technica.com 0001-0203-01
Specications
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
SCALE IS 5 DECIBELS PER DIVISION
240˚
180˚
210˚
270˚
300˚
330˚
150˚
120˚
90˚
30˚
60˚
12" or more on axis
LEGEND
Frequency in Hertz
Response in dB
10 dB
100
50
200
10k
5k
1k
500
2k
20k
Roll-off
frequency response: 20–20,000 Hz
polar pattern
Fixed-charge back plate, permanently
polarized condenser
Cardioid
20-20,000 Hz
80 Hz, 12 dB/octave
–33 dB (22.4 mV) re 1V at 1 Pa
120 ohms
148 dB SPL, 1 kHz at 1% T.H.D.;
158 dB SPL, with 10 dB pad (nominal)
12 dB SPL
136 dB, 1 kHz at Max SPL
82 dB, 1 kHz at 1 Pa
11-52V DC, 3.8 mA typical
Flat, roll-off; 10 dB pad (nominal)
403 g (14.2 oz)
170.0 mm (6.69") long,
52.0 mm (2.05") maximum body diameter
Integral 3-pin XLRM-type
R5
AT8458 shock mount for
5
/
8
"-27
threaded stands;
5
/
8
"-27 to
3
/
8
"-16
threaded adapter; soft protective pouch
Element
Polar pattern
Frequency response
Low frequency roll-off
Open circuit sensitivity
Impedance
Maximum input sound level
Noise
1
Dynamic range (typical)
Signal-to-noise ratio
1
Phantom power requirements
Switches
Weight
Dimensions
Output connector
Audio-Technica case style
Accessories furnished
In the interest of standards development, A.T.U.S.
offers full details on its test methods to other industry
professionals on request.
1 Pascal = 10 dynes/cm
2
= 10 microbars = 94 dB SPL
1
Typical, A-weighted, using Audio Precision System One.
Specications are subject to change without notice.
463

Manual

View the manual for the Audio-Technica AT2035 here, for free. This manual comes under the category microphones and has been rated by 1 people with an average of a 6.3. This manual is available in the following languages: English. Do you have a question about the Audio-Technica AT2035 or do you need help? Ask your question here

Need help?

Do you have a question about the Audio-Technica and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Audio-Technica AT2035 specifications

Below you will find the product specifications and the manual specifications of the Audio-Technica AT2035.

The Audio-Technica AT2035 is a microphone with a microphone input impedance of 120 Ω. It has a microphone sensitivity of 33 dB, making it suitable for capturing a wide range of audio sources. The microphone is wired and uses an XLRM cable type for connectivity. With a weight of 403 grams, the AT2035 is relatively lightweight and easy to handle. The microphone operates on a DC power supply type, consuming 3.8 mA of power. It requires an operating voltage of 11 V, which is supplied by a DC power source. Designed for professional use, the AT2035 is built with quality materials to ensure reliability and durability. It offers a wide frequency response and low self-noise, allowing for clear and accurate audio reproduction. The microphone's cardioid polar pattern focuses on capturing sound from the front while rejecting sound from the sides and rear. This makes it ideal for recording in studios, broadcasting, podcasting, and other professional audio applications. The AT2035 also features a switchable 80 Hz high-pass filter to reduce low-frequency rumble and a -10 dB pad for handling high sound pressure levels. These features provide versatility and adaptability to different recording situations. Overall, the Audio-Technica AT2035 is a reliable and high-quality microphone with a precise and accurate sound reproduction capability. Its professional features and design make it a suitable choice for various audio recording needs.

General
BrandAudio-Technica
ModelAT2035 | AT2035
Productmicrophone
EAN0496131010177, 0609132311840, 0702331136709, 0702706627474, 0712392918855, 0712392918862, 0799928926188, 0989898818945, 4961310101756, 4961310104733, 5052182743126, 5399997976531, 5554442304257, 5554442407774, 7044447790707
LanguageEnglish
FiletypeUser manual (PDF), Datasheet (PDF)
Microphone
Microphone input impedance120 Ω
Microphone sensitivity33 dB
Microphone frequency20 - 20000 Hz
Ports & interfaces
Connectivity technologyWired
Other features
Cable typeXLRM
Weight403 g
Power
Power supply typeDC
Power consumption3.8 mA
Operating voltage11 V
Power sourceDC
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Audio-Technica AT2035 below.

What is the weight of the Audio-Technica AT2035?

The Audio-Technica AT2035 has a weight of 403 g.

What is the microphone input impedance of Audio-Technica AT2035?

The microphone input impedance of Audio-Technica AT2035 is 120 Ω. This impedance value indicates the resistance of the microphone to the flow of electrical current. A lower impedance means better signal quality and compatibility with a wide range of audio equipment.

How sensitive is the Audio-Technica AT2035 microphone?

The microphone sensitivity of Audio-Technica AT2035 is 33 dB. This sensitivity level is relatively high, making it capable of capturing even low-volume sounds with clarity. It is suitable for capturing vocals, instruments, and studio recording applications.

What is the connectivity technology of the Audio-Technica AT2035 microphone?

The connectivity technology of Audio-Technica AT2035 is wired. This means that the microphone requires a physical connection to an audio interface or mixer using a cable.

What type of cable does the Audio-Technica AT2035 microphone use?

The Audio-Technica AT2035 microphone uses an XLRM cable type. XLRM cables are commonly used in professional audio setups due to their balanced nature, which helps in minimizing noise and interference for high-quality audio transmission.

What is the power consumption and source of the Audio-Technica AT2035 microphone?

The power consumption of the Audio-Technica AT2035 microphone is 3.8 mA, and it is powered by DC (direct current). This power consumption level is relatively low, making it energy-efficient. The DC power source ensures stable and reliable performance of the microphone.

How do I properly position the Audio-Technica AT2035 microphone for optimal sound capture?

To properly position the Audio-Technica AT2035 microphone for optimal sound capture, follow these steps: 1. Identify the front of the microphone by locating the Audio-Technica emblem on the microphone. Position this side of the microphone towards the sound source. 2. Secure the microphone to a microphone stand or boom, ensuring that the cable is properly attached and leaving a slack loop at the microphone. This will provide effective shock isolation and prevent accidental disconnection. 3. Adjust the microphone's angle and distance according to your specific recording needs. Experiment with different positions to find the best sound capture. 4. If you are experiencing unwanted low-frequency noise or vibrations, engage the integral 80 Hz high-pass filter by sliding the switch towards the "bent" line. This will reduce the pickup of low-frequency ambient noise and mechanically coupled vibrations. 5. If you need to capture sound sources with high SPL (sound pressure level), such as loud instruments or vocals, engage the switchable 10 dB pad by sliding the switch towards the "-10" position. This will lower the microphone's sensitivity and allow for higher SPL capability. By following these steps, you can ensure that the Audio-Technica AT2035 microphone is properly positioned for optimal sound capture in your recording or performance setup.

What should I do if the Audio-Technica AT2035 microphone is not receiving phantom power?

If the Audio-Technica AT2035 microphone is not receiving phantom power, follow these steps to troubleshoot the issue: 1. Check the phantom power source: Ensure that the audio interface, mixer, or preamp you are using is capable of providing phantom power. Verify that the phantom power switch or button is turned on. 2. Verify the cable connection: Make sure the XLR cable is securely connected to both the microphone and the audio interface, mixer, or preamp. Check for any loose or damaged connections. 3. Test with a different cable: If possible, try using a different XLR cable to rule out any cable-related issues. Sometimes, a faulty cable can prevent the microphone from receiving phantom power. 4. Test with a different audio source: Connect the AT2035 microphone to a different audio interface, mixer, or preamp to see if the issue persists. This will help determine if the problem lies with the microphone or the audio equipment. 5. Contact technical support: If the microphone still does not receive phantom power after following these steps, it is recommended to contact Audio-Technica's technical support for further assistance. They can provide specific troubleshooting steps or arrange for repairs if necessary. By following these steps, you can troubleshoot and resolve the issue of the Audio-Technica AT2035 microphone not receiving phantom power.

How can I troubleshoot feedback issues with the Audio-Technica AT2035 microphone?

To troubleshoot feedback issues with the Audio-Technica AT2035 microphone, follow these steps: 1. Check the microphone placement: Ensure that the microphone is positioned correctly. Place it in front of the sound source, such as a vocalist or instrument, and adjust the distance and angle to achieve the desired sound capture. 2. Adjust the microphone gain: If the microphone gain is set too high, it can lead to feedback. Lower the gain level on your audio interface, mixer, or preamp to reduce the sensitivity of the microphone. 3. Use a pop filter or windscreen: Attach a pop filter or windscreen to the microphone to minimize plosive sounds and wind noise. These accessories can help reduce the chances of feedback caused by sudden bursts of air hitting the microphone. 4. Check the room acoustics: Evaluate the acoustics of the room where you are recording. Excessive reflections or reverberation can contribute to feedback. Consider using acoustic treatment, such as foam panels or diffusers, to improve the room's sound quality. 5. Experiment with microphone positioning and polar pattern: If feedback persists, try adjusting the microphone's position or changing the polar pattern. The AT2035 has a cardioid polar pattern, which provides good isolation from unwanted sound sources. Experiment with different angles and distances to find the optimal position that minimizes feedback. By following these steps, you can troubleshoot and address feedback issues with the Audio-Technica AT2035 microphone, ensuring optimal sound quality in your recordings or performances.

What steps should I take if the Audio-Technica AT2035 microphone is not producing any sound?

To troubleshoot if the Audio-Technica AT2035 microphone is not producing any sound, follow these steps: 1. Check the cable connection: Ensure that the XLR cable is securely connected to both the microphone and the audio interface, mixer, or preamp. Verify that there are no loose or damaged connections. 2. Confirm phantom power: Make sure that the audio interface, mixer, or preamp is providing the required phantom power (11V to 52V DC) to the microphone. Check the phantom power switch or button and ensure it is turned on. 3. Test with another microphone or input: Connect a different microphone to the same audio interface, mixer, or preamp to determine if the issue is specific to the AT2035 microphone or the audio equipment. If another microphone works, it may indicate a problem with the AT2035. 4. Check the microphone settings: Ensure that the microphone is not muted or the volume level is not set too low on the audio interface, mixer, or preamp. Adjust the settings accordingly. 5. Contact technical support: If the microphone still does not produce sound after following these steps, it is recommended to contact Audio-Technica's technical support for further assistance. They can provide specific troubleshooting steps or arrange for repairs if necessary. By following these steps, you can troubleshoot and address the issue of the Audio-Technica AT2035 microphone not producing any sound.

How do I clean and maintain the Audio-Technica AT2035 microphone for long-lasting performance?

To clean and maintain the Audio-Technica AT2035 microphone for long-lasting performance, follow these steps: 1. Regularly wipe the exterior: Use a soft, lint-free cloth to gently wipe the exterior of the microphone. This will remove any dust or fingerprints that may accumulate over time. 2. Clean the grille: Carefully remove the grille from the microphone using a twisting motion. Use a soft brush or compressed air to remove any debris or dust particles that may have accumulated on the grille. Avoid using excessive force to prevent damage. 3. Clean the diaphragm: Take extra caution when cleaning the diaphragm, as it is a sensitive component. Use a small, soft brush or compressed air to remove any dust or debris from the diaphragm. Avoid touching the diaphragm with your fingers or any sharp objects. 4. Store in a safe place: When not in use, store the microphone in a clean and dry environment. Use the included protective pouch or case to prevent dust, moisture, or accidental damage. 5. Avoid exposure to extreme conditions: Protect the microphone from extreme temperatures, high humidity, and direct sunlight. These conditions can potentially damage the microphone's components. By following these steps, you can effectively clean and maintain the Audio-Technica AT2035 microphone, ensuring its long-lasting performance and durability.

Is the manual of the Audio-Technica AT2035 available in English?

Yes, the manual of the Audio-Technica AT2035 is available in English .

Is your question not listed? Ask your question here

No results