ATen VE607 manual

ATen VE607
5.6 · 1
PDF manual
 · 29 pages
English
manualATen VE607
Hardware Setup
9

How to Supply Power

One pair of Power Adapter and Terminal Block Connector is provided in this
package, and can be used on either the Transmitter or Receiver side. The
second Cat 5e cable connection transmits the power signal.
Note: To supply power to each unit separately, you must purchase another set
of power adapter (within a voltage range of +9V~12V) and terminal
block connector. In this case, there is no need to connect the second Cat
5e cable.
The provided Power Adapter and Terminal Block Connector must be
combined. You can then use the modified power adapter to connect – first, to
the terminal block on either the VE157T / VE607T / VE807T or VE157R /
VE607R / VE807R rear panel; and then, to a power outlet to supply power to
your VE157 / VE607 / VE807. Follow the steps described below:
1. Cut off the connector end of the
power adapter.
2. Strip 5mm (0.5 cm) off the
insulation cover of the Power
Adapter cable to expose two wires:
a +9V wire and a GND
(grounding) wire.
3. Insert the exposed +9V wire and
GND wire tightly into the provided
2-pin Terminal Block Connector.
The connector is properly labeled –
the +9V and GND wires should be
plugged into the correct holes.
(Continues on next page.)
The exposed wires must constantly be separated
from each other to prevent any unexpected
damage (including short-circuits, electric shocks,
and so on.)
(+)
(-)
Connector
Provided

Manual

View the manual for the ATen VE607 here, for free. This manual comes under the category AV extenders and has been rated by 1 people with an average of a 5.6. This manual is available in the following languages: English. Do you have a question about the ATen VE607 or do you need help? Ask your question here

Need help?

Do you have a question about the ATen and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

ATen VE607 specifications

Below you will find the product specifications and the manual specifications of the ATen VE607.

General
BrandATen
ModelVE607 | VE607
ProductAV extender
LanguageEnglish
FiletypeUser manual (PDF)
Features
TypeAV transmitter & receiver
Maximum resolution1920 x 1200 pixels
Cable types supportedCat5e, Cat6
Maximum transfer distance60 m
Audio systemstereo
Electrostatic Discharge (ESD) protection15 kV
LED indicatorsYes
Supported video modes1080p
Supported graphics resolutions1280 x 1024 (SXGA), 1920 x 1200 (WUXGA)
Bandwidth6.75 Gbit/s
Bandwidth225 MHz
HDCPYes
MaterialMetal
Plug and PlayYes
Impedance100 Ω
Product colorWhite
Ports & interfaces
DVI input ports1
DVI output ports1
Video in1
Video out1
Audio input1
Audio output1
DC-in jackYes
Connectivity technologyWired
RJ-45 output ports2
RJ-45 input ports2
Power
Operating voltage (transmitter)9 V
Operating voltage (receiver)9 V
Power consumption (transmitter) (max)2.9 W
Power consumption (receiver) (max)2.9 W
External power adapterYes
Operational conditions
Operating temperature (T-T)0 - 50 °C
Storage temperature (T-T)-20 - 60 °C
Operating relative humidity (H-H)0 - 80 %
Weight & dimensions
Receiver dimensions (WxDxH)68.6 x 49.8 x 26.9 mm
Receiver weight180 g
Transmitter dimensions (WxDxH)68.6 x 49.8 x 26.9 mm
Transmitter weight180 g
Packaging content
AC adapter includedYes
ManualYes
Technical details
Sustainability certificatesRoHS
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the ATen VE607 below.

Is the manual of the ATen VE607 available in English?

Yes, the manual of the ATen VE607 is available in English .

Is your question not listed? Ask your question here

No results