Quick Start Guide

NXA-AVB/ETHERNET Modero

Ethernet/Video Breakout Box

Overview

The NXA-AVB/ETHERNET Breakout Box (FG2254-10) facilitates the installation

and distribution of video, data, and audio to Modero touch panels located up to 200 feet (60.96 m) from the AVB box. This unit accepts either Composite or S-Video from standard video devices. FIG. 1 shows the NXA-AVB/ETHERNET Breakout Box.For more detailed installation and operating instructions, refer to the specific

Modero touch panel instruction manual, available online at www.amx.com.

Specifications

NXA-AVB/ETHERNET Breakout Box

FIG. 1 shows the front and rear connectors on the breakout box. Note: The breakout box unit can be mounted on either a horizontal flat surface or into an equipment rack (by removing the front screws and attaching it to an AC-RK).Note: The PSN power supply being used on the NXA-AVB/ETHERNET is dependent on the power requirements of the target touch panel.

Connections and Wiring

A PSN power supply can indirectly provide power to a Modero panel by routing power through the NXA-AVB/ETHERNET Breakout Box. FIG. 2 shows a sample wiring configuration using both an indirect or direct PSN power connection for a video-capable Modero panel. Refer to the online Modero Touch Panel instruction manuals for connection options.

The NXA-AVB/ETHERNET is an optional accessory for non-video capable Modero touch panels but can only transfer Audio signals between the Breakout Box and the target touch panel. A PSN power supply can also directly provide power through the unit to a target Modero panel. Refer to the specific Modero touch panel instruction manual for detailed wiring information. FIG. 3 shows a sample wiring configuration for a non-video capable Modero panel.

Note: AMX recommends using the above power connection examples when

connecting the breakout box to your touch panel. If you want to attempt another configuration or if you want to use two power supplies, be sure to avoid any potential ground loops that may occur in your connection configuration. Ground loops can cause display errors with your touch panel.Wiring the NXA-AVB/ETHERNET connectors and cablesThe inputs and outputs on the breakout box are separated into front and rear connectors. The rear connectors are used to input external signals. The front connectors are used to communicate signals between the NXA-AVB/ETHERNET and a target Modero panel. FIG. 4 provides a layout of the wiring connection both into and from the breakout box.

FIG. 1 Connector layouts on the NXA-AVB/ETHERNET Breakout Box NXA-AVB/ETHERNET SpecificationsDimensions (HWD):• 1.50" x 5.55" x 4.88" (3.81 cm x 14.10 cm x 12.40 cm)• Width when attached to mounting ears: 6.65" (16.89 cm)Power Consumption:• 50mA (with audio/video input) • 23mA (with no audio/video)• Routed through AVB using a PSN power supply (Refer to FIG. 2 and FIG. 3 for more information).Certifications: • FCC, CE, and EN60950Front Components: • 2-pin 3.5 mm Phoenix connector for power to the touch panel• Green LED provides an indication of power status• RJ-45 connector provides Ethernet signals to the touch panel• RJ-45 connector provides differential audio and video signals to the touch panel (panel type dependent)Rear Components: • 6-pin 3.5 mm Phoenix connector for in-bound (left/right channel) audio• 4-pin 3.5 mm Phoenix connector for out-bound (from microphone) audio• BNC connector (female) for Composite or Chroma

(for video-capable panels only)

• BNC connector (female) for luminance (for video-capable panels only)• RJ-45 connector for Ethernet input from the control system• 2-pin 3.5 mm Phoenix connector for in-bound power Features: • Accepts either Composite or S-Video (video-capable panels only)• Provides audio distribution to the non-video touch panels over a CAT5 cable (up to 200 ft.)• Provides video/audio distribution to the video-capable touch panels over CAT5 cable up to 200 ft. (60.9 m)Availability: • This unit is not included with current Modero panels• This unit is included with VG-series Video Kits and with the 7" panels Included Accessories:• Two 2-pin Phoenix connectors (41-5025)• One 4-pin Phoenix connector (41-5047)• One 6-pin Phoenix connector (41-5063)• One Rack Mount Kit (KA2250-40) with mounting bracket (62-2254-02)Optional Accessories:• AC-RK Accessory RackMount Kit (FG515)• Modero Table Top Cable (CA2250-50)

• PSN6.5 power supply (FG423-41) (panel dependent)

Power(front)Ethernet (to panel)Audio/Video Power (to panel)S-Video ChromaComposite/Mic OutAudio

EthernetS-Video

Luma

(rear)(to panel)

FIG. 2 Sample wiring configuration on video-capable panels using this Breakout Box

FIG. 3 Sample Wiring configuration on non-video panel using this Breakout BoxNXD/T Video-capableEthernet InPSN power(RJ-45)Video In(BNC)Mic Out(4-pin captive-wire)Audio In(6-pin captive-wire)NXA-AVB/ETHERNETPSN4.4/6.5supplied viaNXA-AVB boxAudio/Video(CAT5)Line Level out(to amplifieror VOL card)Touch Panels

DirectConnectBreakout BoxEthernet(rear)(front)(CAT5)supplyIndirectConnectPSN powersupplyDirectconnectNXD/T Non-video capableEthernet(CAT5)Touch PanelsPSN powerAudio (CAT5)between optionalNXA-AVB/ETHERNETBreakout Boxsupply

Need help?

Number of questions: 0

Do you have a question about the AMX NXA-AVB/ETHERNET or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other AMX NXA-AVB/ETHERNET owners to properly answer your question.

Index

❯ NXA-AVB/ETHERNET Modero Ethernet/Video Breakout Box Quick Start Guide

About the AMX NXA-AVB/ETHERNET

View the manual for the AMX NXA-AVB/ETHERNET here, for free. This manual comes under the category AV extenders and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the AMX NXA-AVB/ETHERNET or do you need help? Ask your question here