Allied Telesis AT-SBX81XS6 manual

Allied Telesis AT-SBX81XS6
8.6 · 1
PDF manual
 · 314 pages
English
manualAllied Telesis AT-SBX81XS6
SwitchBlade x8112 Chassis Switch and AT-SBx81CFC960 Card Installation Guide
Section III: Building a Stack with VCStack Plus 285

Setting the ID Number

The chassis must be assigned the ID number 1 or 2. The ID number is
used to identify the chassis when you configure the device with the
command line interface. The two chassis of the stack must be assigned
different ID numbers. To set the ID number on the chassis, perform the
following procedure:
1. From the Privileged Exec mode, enter the SHOW STACK command to
view the current ID number of the switch:
awplus# show stack
Figure 172 is an example of the command.
Figure 172. SHOW STACK Command
The command lists the AT-SBx81CFC960 Controller Fabric Cards in
the stack. Given that the switch is not operating as part of a stack yet,
the command lists only the controller cards in the switch you are
currently configuring. The switch in Figure 172 has two controller
cards. The command displays only one controller card if the chassis
has only one card.
The ID number of a controller card contains two numbers. The first
number is the chassis ID number. This number is always 1 or 2. If the
chassis has two controller cards, both cards have the same chassis ID
number. The second number is the slot number in which the controller
card is installed. For example, the first controller card in the example
has the ID number 1.5, meaning that the card has the chassis ID
number 1 and is installed in slot 5 of the unit. The second controller
card has the same chassis ID number and is installed in slot 6.
2. Check the chassis ID number of the controller cards. (As just
explained, the chassis ID number is the first number in the ID number.)
The chassis ID number can be 1 or 2. The default value is 1. The two
chassis of a stack must have different ID numbers. Do one of the
following:
If the ID number is already set correctly for the chassis, go to
“Setting the Priority Number” on page 289. For example, if you are
Virtual Chassis Stacking summary information
ID Pending ID MAC address Priority Status Role
1.5 - eccd.6d9e.07e1 128 Ready Active CFC
1.6 - eccd.6d9e.0145 128 Ready Backup Member
Current ID Numbers

Manual

View the manual for the Allied Telesis AT-SBX81XS6 here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 8.6. This manual is available in the following languages: English. Do you have a question about the Allied Telesis AT-SBX81XS6 or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Allied Telesis and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Allied Telesis AT-SBX81XS6 specifications

Below you will find the product specifications and the manual specifications of the Allied Telesis AT-SBX81XS6.

General
BrandAllied Telesis
ModelAT-SBX81XS6 | AT-SBX81XS6
Productnot categorized
EAN0767035195957, 767035195957, 7670351959574
LanguageEnglish
FiletypeUser manual (PDF)
Optical fiber
Fiber optic connectorSFP+
Data transmission
Data transfer rate10 Gbit/s
Ports & interfaces
Fiber ports quantity6
Performance
Compatibilityx8100
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Allied Telesis AT-SBX81XS6 below.

Is the manual of the Allied Telesis AT-SBX81XS6 available in English?

Yes, the manual of the Allied Telesis AT-SBX81XS6 is available in English .

Is your question not listed? Ask your question here

No results