Allied Telesis AT-SBX81XS6 manual

Allied Telesis AT-SBX81XS6
8.6 · 1
PDF manual
 · 314 pages
English
manualAllied Telesis AT-SBX81XS6
SwitchBlade x8112 Chassis Switch and AT-SBx81CFC960 Card Installation Guide
Section II: Installing the Chassis 217

AT-SBx81CFC960 Controller Fabric Card

If the chassis has one controller card and the card fails, all network
operations stop. The Ethernet line cards stop forwarding all network traffic
until the controller card is replaced.
If the chassis has two controller cards and one fails, the Ethernet line
cards continue to forward traffic, but the bandwidth of the backplane is
reduced, which, depending on the number of Ethernet line cards present
and the amount of traffic traversing the backplane, may result in slower
network operations.
If the chassis has one controller card, examine the M/S LED on the card.
The LED should be solid green. If the LED is flashing amber, the card is
initializing its management software. Wait one or two minutes for the card
to complete the process and check the LED again. If it has not changed to
solid green, the card cannot complete the initialization process. Try
moving the controller card to the other controller card slot, slot 5 or 6, to
see if it works in a different slot. You might also try connecting a terminal or
PC with a terminal emulator program to the Console RS232 port to watch
for any error messages.
If the chassis has two controller cards, check the M/S LEDs on both cards.
The LEDs should be solid green on one card and solid or flashing amber
on the other card. If the LEDs are both flashing amber, they are initializing
their management software. Wait one or two minutes for the cards to
complete the process and check the LEDs again. If both LEDs are still
flashing amber, the cards cannot complete the initialization process. Try
replacing the cards.
The controller card has an onboard battery to maintain the date and time
when the chassis is powered off or reset. If you manually set the date and
time but the card loses the information after you power off or reset the unit,
you may have forgotten to remove the battery insulator when you installed
the card in the chassis. The insulator is shown in Figure 66 on page 130.
The only way to remedy the problem is to remove the controller card from
the chassis and remove the battery insulator. If the chassis has only one
controller card, removing the card causes the Ethernet line cards to stop
forwarding traffic.

Manual

View the manual for the Allied Telesis AT-SBX81XS6 here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 8.6. This manual is available in the following languages: English. Do you have a question about the Allied Telesis AT-SBX81XS6 or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Allied Telesis and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Allied Telesis AT-SBX81XS6 specifications

Below you will find the product specifications and the manual specifications of the Allied Telesis AT-SBX81XS6.

General
BrandAllied Telesis
ModelAT-SBX81XS6 | AT-SBX81XS6
Productnot categorized
EAN0767035195957, 767035195957, 7670351959574
LanguageEnglish
FiletypeUser manual (PDF)
Optical fiber
Fiber optic connectorSFP+
Data transmission
Data transfer rate10 Gbit/s
Ports & interfaces
Fiber ports quantity6
Performance
Compatibilityx8100
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Allied Telesis AT-SBX81XS6 below.

Is the manual of the Allied Telesis AT-SBX81XS6 available in English?

Yes, the manual of the Allied Telesis AT-SBX81XS6 is available in English .

Is your question not listed? Ask your question here

No results