Allied Telesis AT-SBX81XS6 manual

Allied Telesis AT-SBX81XS6
8.6 · 1
PDF manual
 · 314 pages
English
manualAllied Telesis AT-SBX81XS6
Chapter 11: Troubleshooting
208 Section II: Installing the Chassis

AT-SBxPWRSYS1 and AT-SBxPWRPOE1 AC Power Supplies

A power supply is operating normally when its AC and DC LEDs are solid
green and the Fault LED is off. Possible fault conditions and their solutions
are described here:
Fault Condition 1: If the AC LED is off, the power supply is not receiving
power, has overheated and been disabled, or has failed and needs to be
replaced. Try the following:
Verify that there is a power cord connected to the power supply’s
connector on the back panel of the chassis. For example, if a
power supply in slot C does not have power, check for a power
cord on connector C on the back panel.
Verify that the power cord is securely connected to the chassis and
the AC power source.
Verify that the AC power has power by connecting another device
to it.
Verify that the power from the AC power source is within the
required levels for your region.
If the chassis is still operating, use the SHOW PSU or SHOW PSU
ALL command from a local or remote management session to
determine if the power supply has overheated and shutdown.
Fault Condition 2: If the AC LED is solid green and the DC LED is off, the
power unit is generating insufficient DC power. Replace the power supply.
Fault Condition 3: If the Fault LED is solid amber, try the solutions in Fault
Condition 1. If they do not resolve the problem, replace the power supply.
Note
The power supplies are hot swappable in a redundant configuration.
This allows the AT-SBx8112 Chassis to continue operating while
you exchange power supplies.
Fault Condition 4: If the LEDs on the power supply indicate normal
operations but the PSU LED on the active master controller card is
showing a fault condition, the problem may be with one of the two power
supply interfaces (opto-couplers) on the rear panel of the chassis. For
troubleshooting suggestions, refer to “Power Supply Interfaces (Opto-
couplers)” on page 220.
Caution
The power supply interfaces are not hot swappable and should only
be serviced by an authorized service technician.

Manual

View the manual for the Allied Telesis AT-SBX81XS6 here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 8.6. This manual is available in the following languages: English. Do you have a question about the Allied Telesis AT-SBX81XS6 or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Allied Telesis and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Allied Telesis AT-SBX81XS6 specifications

Below you will find the product specifications and the manual specifications of the Allied Telesis AT-SBX81XS6.

General
BrandAllied Telesis
ModelAT-SBX81XS6 | AT-SBX81XS6
Productnot categorized
EAN0767035195957, 767035195957, 7670351959574
LanguageEnglish
FiletypeUser manual (PDF)
Optical fiber
Fiber optic connectorSFP+
Data transmission
Data transfer rate10 Gbit/s
Ports & interfaces
Fiber ports quantity6
Performance
Compatibilityx8100
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Allied Telesis AT-SBX81XS6 below.

Is the manual of the Allied Telesis AT-SBX81XS6 available in English?

Yes, the manual of the Allied Telesis AT-SBX81XS6 is available in English .

Is your question not listed? Ask your question here

No results