Allied Telesis AT-SBX81XS6 manual

Allied Telesis AT-SBX81XS6
8.6 · 1
PDF manual
 · 314 pages
English
manualAllied Telesis AT-SBX81XS6
SwitchBlade x8112 Chassis Switch and AT-SBx81CFC960 Card Installation Guide
Section II: Installing the Chassis 157

Cabling the NET MGMT Port on the AT-SBx81CFC960 Card

The controller card must have access to your network to perform the
management features in Table 19 on page 71. You can give the controller
card access to your network either by configuring the Inband Interface,
which enables the card to use the backplane and Ethernet line cards to
communicate with your network, or by connecting the NET MGMT port to
a network device, such as a switch or router. (For instructions on how to
configure the Inband Interface, refer to the Software Reference for
SwitchBlade x8100 Series Switches.)
Here are the guidelines to using the NET MGMT port:
You may connect the NET MGMT port to a switch, router, media
converter, workstation, or other network device.
The cabling requirements of the port are the same as the ports on
the AT-SBx81GT24 Line Card, in Table 11 on page 52.
If the chassis has two AT-SBx81CFC960 Controller Fabric Cards,
you may connect the NET MGMT ports on the active and standby
master controller cards to the same network device or different
devices.
The default speed setting for the port is Auto-Negotiation. This
setting is appropriate if the port is connected to a network device
that also support Auto-Negotiation.
The default speed setting of Auto-Negotiation is not appropriate if
the port is connected to a network device that does not support
Auto-Negotiation and has a fixed speed or 10 or 100 Mbps. In this
situation, disable Auto-Negotiation and set the port’s speed
manually to match the speed of the network device.
The port must be set to Auto-Negotiation, the default setting, to
operate at 1000Mbps.
The default duplex mode setting for the port is Auto-Negotiation.
This setting is appropriate if the port is connected to a network
device that also support Auto-Negotiation for the duplex mode.
The default duplex mode setting of Auto-Negotiation is not
appropriate if the port is connected to a network device that does
not support Auto-Negotiation and has a fixed duplex mode. In this
situation, you should disable Auto-Negotiation on the port and set
its duplex mode manually to avoid the possibility of a duplex mode
mismatch. With Auto-Negotiation, the port defaults to half-duplex if
it detects that the end node is not using Auto-Negotiation. This can
result in a mismatch if the end node is operating at a fixed duplex
mode of full-duplex.
The default wiring configuration of the port is automatic MDIX
detection, which configures the MDI/MDIX setting automatically.

Manual

View the manual for the Allied Telesis AT-SBX81XS6 here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 8.6. This manual is available in the following languages: English. Do you have a question about the Allied Telesis AT-SBX81XS6 or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Allied Telesis and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Allied Telesis AT-SBX81XS6 specifications

Below you will find the product specifications and the manual specifications of the Allied Telesis AT-SBX81XS6.

General
BrandAllied Telesis
ModelAT-SBX81XS6 | AT-SBX81XS6
Productnot categorized
EAN0767035195957, 767035195957, 7670351959574
LanguageEnglish
FiletypeUser manual (PDF)
Optical fiber
Fiber optic connectorSFP+
Data transmission
Data transfer rate10 Gbit/s
Ports & interfaces
Fiber ports quantity6
Performance
Compatibilityx8100
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Allied Telesis AT-SBX81XS6 below.

Is the manual of the Allied Telesis AT-SBX81XS6 available in English?

Yes, the manual of the Allied Telesis AT-SBX81XS6 is available in English .

Is your question not listed? Ask your question here

No results