Allied Telesis AT-SBX81XS6 manual

Allied Telesis AT-SBX81XS6
8.6 · 1
PDF manual
 · 314 pages
English
manualAllied Telesis AT-SBX81XS6
Chapter 8: Installing the Transceivers and Cabling the Ports
142 Section II: Installing the Chassis
Cabling Guidelines for the Twisted Pair Ports on the AT-SBx81GT24,

AT-SBx81GT40, and AT-SBx81GP24 Line Cards

Here are the guidelines to cabling the 10/100/1000Base-T twisted pair
ports on the AT-SBx81GT24, AT-SBx81GP24, and AT-SBx81GT40 Line
Cards:
The 10/100/1000Base-T twisted pair ports on the AT-SBx81GT24
and AT-SBx81GP24 Line Cards have 8-pin RJ45 connectors.
The 10/100/1000Base-T twisted pair ports on the AT-SBx81GT40
Line Card have 8-pin RJ point 5 connectors.
The cable specifications for the 10/100/1000Base-T twisted pair
ports on the AT-SBx81GT24 and AT-SBx81GT40 Line Cards are
listed in Table 11 on page 52.
The cable specifications for the 10/100/1000Base-T twisted pair
ports on the AT-SBx81GP24 Line Card are listed in Table 12 on
page 53.
The connectors on the cables should fit snugly into the ports, and
the tabs should lock the connectors into place.
The default setting for PoE on the ports on the AT-SBx81GP24
Line Card is enabled.
The default speed setting for the ports is Auto-Negotiation. This
setting is appropriate for ports connected to network devices that
also support Auto-Negotiation.
The default speed setting of Auto-Negotiation is not appropriate for
ports connected to network devices that do not support Auto-
Negotiation and have fixed speeds or 10 or 100 Mbps. For those
switch ports, disable Auto-Negotiation and set the port’s speed
manually to match the speeds of the network devices.
The 10/100/1000Base-T ports must be set to Auto-Negotiation, the
default setting, to operate at 1000Mbps.
The default duplex mode setting for the ports is Auto-Negotiation.
This setting is appropriate for ports connected to network devices
that also support Auto-Negotiation for duplex modes.
The default duplex mode setting of Auto-Negotiation is not
appropriate for ports connected to network devices that do not
support Auto-Negotiation and have a fixed duplex mode. Disable
Auto-Negotiation on those ports and set their duplex modes
manually to avoid the possibility of duplex mode mismatches. A
switch port using Auto-Negotiation defaults to half-duplex if it
detects that the end node is not using Auto-Negotiation. This can
result in a mismatch if the end node is operating at a fixed duplex
mode of full-duplex.

Manual

View the manual for the Allied Telesis AT-SBX81XS6 here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 8.6. This manual is available in the following languages: English. Do you have a question about the Allied Telesis AT-SBX81XS6 or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Allied Telesis and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Allied Telesis AT-SBX81XS6 specifications

Below you will find the product specifications and the manual specifications of the Allied Telesis AT-SBX81XS6.

General
BrandAllied Telesis
ModelAT-SBX81XS6 | AT-SBX81XS6
Productnot categorized
EAN0767035195957, 767035195957, 7670351959574
LanguageEnglish
FiletypeUser manual (PDF)
Optical fiber
Fiber optic connectorSFP+
Data transmission
Data transfer rate10 Gbit/s
Ports & interfaces
Fiber ports quantity6
Performance
Compatibilityx8100
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Allied Telesis AT-SBX81XS6 below.

Is the manual of the Allied Telesis AT-SBX81XS6 available in English?

Yes, the manual of the Allied Telesis AT-SBX81XS6 is available in English .

Is your question not listed? Ask your question here

No results