AEG X69163MD10 manual

AEG X69163MD10
5.9 · 1
PDF manual
 · 132 pages
English
manualAEG X69163MD10
59
LIETUVIŠKAI

PUIKIEMS REZULTATAMS PASIEKTI

Ačiū, kad pasirinkite šį AEG gaminį. Mes sukūrėme jį taip, kad jis nepriekaištingai veiktų
daugelį metų – pasižymintis pažangiomis technologijomis, kurios padeda palengvinti
gyvenimą, jis turi funkcijų, kurių galite nerasti įprastuose buitiniuose prietaisuose. Skirkite
kelias minutes perskaityti insktrukciją, kad galėtumėte jį maksimaliai panaudoti.
Apsilankykite mūsų interneto svetainėje, kad:
gautumėte naudojimo patarimų, brošiūrų, trikčių šalinimo, aptarnavimo informacijos:
www.aeg.com
užregistruotumėte savo gaminį geresniam aptarnavimui:
www.aeg.com/productregistration
įsigytumėte priedų, vartojamųjų prekių ir originalių atsarginių dalių savo prietaisui:
www.aeg.com/shop

APLINKOS APSAUGA

Atiduokite perdirbti medžiagas, pažymėtas šiuo ženklu . Išmeskite pakuotę į atitinkamą
atliekų surinkimo konteinerį, kad ji būtų perdirbta.
Padėkite saugoti aplinką bei žmonių sveikatą ir surinkti bei perdirbti elektros ir elektronikos
prietaisų atliekas. Neišmeskite šiuo ženklu pažymėtų prietaisų kartu su kitomis
buitinėmis atliekomis. Atiduokite šį gaminį į vietos atliekų surinkimo punktą arba susisiekite
su vietnos savivaldybe dėl papildomos informacijos.

KLIENTŲ PRIEŽIŪRA IR APTARNAVIMAS

Rekomenduojame naudoti tik originalias atsargines dalis.
Kreipdamiesi į aptarnavimo centrą, būtinai pateikite šią informaciją.
Informacija yra nurodyta techninių duomenų plokštelėje. Modelis, PNC, serijos numeris.
Įspėjimas / atsargumo ir saugos informacija.
Galimi pakeitimai be įspėjimo.

SAUGOS INFORMACIJA

Prieš atlikdami bet kokius valymo ar priežiūros veiksmus,

atjunkite gartraukį nuo elektros tinklo ištraukdami maitinimo

laido kištuką ar išjungdami pagrindinį namo jungiklį.

Atlikdami visus montavimo ir priežiūros darbus mūvėkite

darbines pirštines.

Vaikai nuo 8 metų amžiaus ir asmenys su ribotomis

zinėmis, jutimo ar psichinėmis galimybėmis, ar neturintys

patirties ar reikalingų žinių, gali naudoti aparatą su priežiūra

arba gavę atitinkamas instrukcijas apie saugų aparato

naudojimą bei supratę visus pavojus, susijusius su jo

naudojimu.

Vaikai turi būti prižiūrimi, kad nežaistų su įrenginiu.

Valymas ir priežiūra negali būti atliekama vaikų be priežiūros.

Patalpoje turi būti pakankama ventiliacija, kai virtuvinis

LT NAUDOTOJO VADOVAS

Manual

View the manual for the AEG X69163MD10 here, for free. This manual comes under the category exhaust hoods and has been rated by 1 people with an average of a 5.9. This manual is available in the following languages: English. Do you have a question about the AEG X69163MD10 or do you need help? Ask your question here

Need help?

Do you have a question about the AEG and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

AEG X69163MD10 specifications

Below you will find the product specifications and the manual specifications of the AEG X69163MD10.

General
BrandAEG
ModelX69163MD10 | 942 150 212
Productexhaust hood
EAN7332543384297
LanguageEnglish
FiletypeUser manual (PDF)
Performance
Type of extraction-
Maximum extraction power600 m³/h
Fluid dynamic efficiency classB
Lighting efficiency classE
Grease filtering efficiency classB
Number of speeds3
Intensive speedYes
Noise level51 dB
Noise level (high speed)71 dB
Design
TypeWall-mounted
Product colorStainless steel
Built-in display-
Number of motors1
Lighting
Bulb typeHalogen
Filtering
Grease filter type-
Power
Energy efficiency classC
Motor power241 W
AC input voltage220-240 V
AC input frequency50 Hz
Annual energy consumption82.1 kWh
Weight & dimensions
Width898 mm
Depth450 mm
Height622 mm
Height (max)1152 mm
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the AEG X69163MD10 below.

When should I replace the carbon filter on my extractor hood?

The carbon filter should be replaced every three to twelve months.

How often should I clean the metal hood grease filters?

The metal grease filters should be cleaned every eight to ten weeks.

Where can I find the model number of my cooker ectractor hood?

The model number of the hood is usually found on a white label inside the hood.

What is the height of the AEG X69163MD10?

The AEG X69163MD10 has a height of 622 mm.

What is the width of the AEG X69163MD10?

The AEG X69163MD10 has a width of 898 mm.

What is the depth of the AEG X69163MD10?

The AEG X69163MD10 has a depth of 450 mm.

What energy label does the AEG X69163MD10 have?

The AEG X69163MD10 has energy label C.

What is the maximum extraction power of the AEG X69163MD10?

The AEG X69163MD10 has a maximum extraction power of 600 m³/h. This means it is capable of efficiently removing odors and smoke from your kitchen.

What is the fluid dynamic efficiency class of the AEG X69163MD10?

The fluid dynamic efficiency class of the AEG X69163MD10 is B. This indicates that it performs moderately well in terms of airflow efficiency compared to other similar products on the market.

What is the lighting efficiency class of the AEG X69163MD10?

The lighting efficiency class of the AEG X69163MD10 is E. This means that it is not as energy-efficient as some other exhaust hoods when it comes to its lighting feature.

Does the AEG X69163MD10 have an intensive speed option?

Yes, the AEG X69163MD10 has an intensive speed option. This allows for powerful and quick extraction when needed, perfect for when you are cooking dishes that produce a lot of smoke or strong odors.

What is the noise level of the AEG X69163MD10 on high speed?

The noise level of the AEG X69163MD10 on high speed is 71 dB. While this may be slightly louder than some other models, it is still within an acceptable range and should not cause significant disturbance in your kitchen.

How do I clean the filters of the AEG X69163MD10 exhaust hood?

To clean the filters of the AEG X69163MD10 exhaust hood, follow these steps: 1. Turn off the exhaust hood and unplug it from the power source for safety. 2. Locate the grease filter, which is responsible for trapping grease and other particles. 3. Remove the grease filter from the exhaust hood. Depending on the model, it may be located at the bottom or on the sides of the hood. 4. Clean the grease filter using non-aggressive detergents. You can either wash it by hand or place it in the dishwasher on a low temperature and short cycle. 5. If washing by hand, use a cloth dampened with neutral liquid detergent to gently clean the filter. Avoid using abrasive products or alcohol. 6. If using the dishwasher, ensure that the grease filter is securely placed in the dishwasher and set it to the appropriate settings. 7. After cleaning, allow the grease filter to dry completely before reinstalling it in the exhaust hood. 8. Once the grease filter is dry, carefully insert it back into its original position in the exhaust hood. 9. Ensure that the grease filter is properly secured and aligned before turning on the exhaust hood again. Regularly cleaning the grease filter of the AEG X69163MD10 exhaust hood helps maintain its performance and prevents the risk of fire.

Why is the exhaust hood making a loud noise during operation?

The AEG X69163MD10 exhaust hood may make a loud noise during operation due to various reasons. Here are some possible causes and solutions: 1. Grease Build-up: If the exhaust hood has not been cleaned regularly, grease can accumulate on the fan blades, causing noise. Clean the fan blades and the interior of the hood following the cleaning instructions in the manual. 2. Loose or Damaged Parts: Check for any loose or damaged parts, such as screws or brackets, that may be causing vibrations or rattling noises. Tighten or replace any loose or damaged parts as necessary. 3. Fan Motor Issues: The fan motor may be malfunctioning or worn out, resulting in excessive noise. Contact a qualified technician to inspect and repair or replace the fan motor if needed. 4. Improper Installation: Ensure that the exhaust hood is properly installed and securely mounted. Loose or incorrect installation can cause vibrations and noise during operation. Refer to the installation instructions in the manual or consult a professional for assistance. 5. External Factors: Noise from the exhaust hood can also be caused by external factors such as airflow restrictions, nearby objects, or improper ducting. Check for any obstructions or restrictions in the airflow and ensure that the ducting is properly installed and not damaged. By addressing these possible causes, you can reduce or eliminate the loud noise during operation of the AEG X69163MD10 exhaust hood.

How do I switch between external evacuation and internal recirculation modes?

To switch between external evacuation and internal recirculation modes on the AEG X69163MD10 exhaust hood, follow these steps: 1. Determine the desired mode of operation based on your kitchen setup and preferences. External evacuation mode removes cooking fumes and odors by venting them outside through a duct. Internal recirculation mode filters the air and recirculates it back into the kitchen. 2. If you want to switch to external evacuation mode, ensure that your kitchen has a suitable ducting system in place. Connect the exhaust hood to the duct using the appropriate materials and follow the installation instructions provided in the manual. 3. If you prefer internal recirculation mode, make sure that the grease filter and activated charcoal filter are properly installed in the exhaust hood. These filters help trap grease and odors before recirculating the air back into the kitchen. 4. To access the filters, refer to the maintenance section of the manual for detailed instructions on removing and installing them. Follow the recommended cleaning and replacement intervals for optimal performance. 5. Once the desired mode is set, ensure that the exhaust hood is securely mounted and connected to the power supply. Test the operation of the hood to ensure proper functionality. By following these steps, you can easily switch between external evacuation and internal recirculation modes on the AEG X69163MD10 exhaust hood according to your needs.

Why is the exhaust hood not turning on when I press the power button?

If the AEG X69163MD10 exhaust hood is not turning on when you press the power button, you can follow these steps to troubleshoot the issue: 1. Check the Power Supply: Ensure that the exhaust hood is properly connected to a functioning power outlet. Verify that the power cord is securely plugged in and there is power supply to the outlet. 2. Check the Circuit Breaker: If the power outlet is working, check the circuit breaker or fuse box to see if the circuit for the exhaust hood has tripped or blown a fuse. Reset the circuit breaker or replace the fuse if necessary. 3. Test the Control Panel: Inspect the control panel for any visible damage or signs of malfunction. Clean the control panel using a soft, dry cloth to remove any dirt or debris that may be affecting the button's functionality. 4. Check the Safety Switch: Some exhaust hoods have a safety switch that prevents the hood from turning on if the filters are not properly installed. Ensure that the grease filter and any other required filters are correctly installed and securely in place. 5. Contact Customer Support: If the above steps do not resolve the issue, it is recommended to contact AEG customer support or a qualified technician for further assistance. They will be able to provide specific troubleshooting steps or arrange for a repair if needed. By following these steps, you can identify and resolve common issues that may prevent the AEG X69163MD10 exhaust hood from turning on when you press the power button.

How do I replace the lamp in the AEG X69163MD10 exhaust hood?

To replace the lamp in the AEG X69163MD10 exhaust hood, follow these steps: 1. Disconnect the hood from the electricity to ensure safety. 2. Allow the lamp to cool down completely before handling it. 3. Identify the type of lamp required for replacement. The manual specifies using a new 12 Volt, 20 Watt halogen light with a G-4 base suitable for use in open luminaires. 4. Follow the package directions provided with the replacement lamp. 5. Carefully remove the old lamp from its socket. Avoid touching the new lamp with bare hands, as this can reduce its lifespan. If necessary, use a clean cloth or gloves to handle the lamp. 6. Insert the new lamp into the socket, ensuring it is securely seated. 7. Reconnect the hood to the power supply. It is important to note that lamp replacement should only be done with the specific lamp type indicated in the Maintenance/Replacing lamps section of the manual. If you have any doubts or difficulties, consult an authorized service assistance center or a qualified person for assistance.

How do I clean the filters of the AEG X69163MD10 exhaust hood?

To clean the filters of the AEG X69163MD10 exhaust hood, follow these steps: 1. Turn off the exhaust hood and unplug it from the power source for safety. 2. Locate the grease filter, which is responsible for trapping grease and other particles from the cooking fumes. 3. Remove the grease filter from the exhaust hood. It can usually be accessed by opening a panel or sliding it out. 4. Clean the grease filter using non-aggressive detergents. You can wash it by hand or place it in the dishwasher on a low temperature and short cycle. 5. If washing in the dishwasher, ensure that the grease filter is placed securely and that the dishwasher settings are appropriate. 6. After cleaning, inspect the grease filter for any discoloration or damage. If necessary, replace the filter with a new one. 7. Once the grease filter is clean or replaced, reinsert it back into the exhaust hood in the correct position. 8. Wipe the exterior of the exhaust hood with a cloth dampened with neutral liquid detergent. Avoid using abrasive products or alcohol. 9. Reconnect the exhaust hood to the power source and ensure it is functioning properly. Regularly cleaning the filters of the AEG X69163MD10 exhaust hood helps maintain its performance and prevents the risk of fire.

Why is the exhaust hood making a loud noise during operation?

The AEG X69163MD10 exhaust hood may make a loud noise during operation due to the following reasons: 1. Incorrect Installation: Ensure that the exhaust hood is properly installed according to the instructions provided in the manual. Check if all the screws and fixings are securely tightened. 2. Loose or Damaged Parts: Inspect the exhaust hood for any loose or damaged parts, such as the fan blades or motor. Tighten any loose parts or replace damaged components as necessary. 3. Blocked or Dirty Filters: Check if the grease filters or other filters in the exhaust hood are blocked or dirty. Clean or replace the filters according to the cleaning instructions provided in the manual. 4. Improper Ventilation: Ensure that the exhaust hood is properly connected to the ventilation system. Check if the ducting is clear and free from any obstructions that may restrict airflow. 5. Fan Speed Setting: Adjust the fan speed setting to a lower level if the noise is primarily coming from the high-speed setting. This can help reduce the noise generated by the exhaust hood. If the loud noise persists or if you have any concerns about the operation of the AEG X69163MD10 exhaust hood, it is recommended to contact an authorized service center for further assistance.

How do I switch between external evacuation and internal recirculation modes?

To switch between external evacuation and internal recirculation modes on the AEG X69163MD10 exhaust hood, follow these steps: 1. Ensure that the exhaust hood is properly installed according to the instructions provided in the manual. 2. Locate the control panel on the front of the exhaust hood. 3. Look for the suction speed selection control, which allows you to adjust the fan speed. 4. To switch to external evacuation mode, select the appropriate suction speed setting for external evacuation. This mode requires the exhaust hood to be connected to an external ventilation system that expels the fumes and vapors outside. 5. To switch to internal recirculation mode, select the appropriate suction speed setting for internal recirculation. This mode does not require an external ventilation system and recirculates the filtered air back into the kitchen. 6. Once you have selected the desired mode, the exhaust hood will operate accordingly. 7. Remember to follow any additional instructions or recommendations provided in the manual regarding the specific mode you have chosen. By following these steps, you can easily switch between external evacuation and internal recirculation modes on the AEG X69163MD10 exhaust hood to suit your ventilation needs.

What should I do if the lamp in the AEG X69163MD10 exhaust hood is not working?

If the lamp in the AEG X69163MD10 exhaust hood is not working, you can follow these steps to address the issue: 1. Disconnect the exhaust hood from the electricity for safety. 2. Allow the lamp to cool down before handling it. 3. Check if the lamp is a 12 Volt, 20 Watt halogen light with a G-4 base, suitable for use in open luminaires. Ensure that the lamp meets these specifications. 4. If the lamp is damaged or burnt out, replace it with a new one that matches the specifications mentioned above. Follow the package directions for proper installation. 5. Avoid touching the new lamp with bare hands, as this can reduce its lifespan. Use a clean cloth or gloves when handling the lamp. 6. After replacing the lamp, reconnect the exhaust hood to the power source. 7. Test the lamp to see if it is functioning properly. If the lamp still does not work after following these steps, it is recommended to contact an authorized service center for further assistance.

How do I ensure proper ventilation when using the exhaust hood?

To ensure proper ventilation when using the AEG X69163MD10 exhaust hood, follow these steps: 1. Regular Cleaning: Clean the exhaust hood regularly, both internally and externally, to remove any grease or dirt buildup. Use a cloth dampened with neutral liquid detergent for cleaning. Avoid using abrasive products or alcohol. 2. Grease Filter Maintenance: Clean the grease filter once a month using non-aggressive detergents. You can wash it by hand or place it in the dishwasher on a low temperature and short cycle. Ensure that the filter is completely dry before reinserting it into the exhaust hood. 3. Charcoal Filter Replacement: If your exhaust hood is equipped with a non-washable activated charcoal filter, replace the filter at least every four months. The saturation of the charcoal filter depends on the type of cooking and the regularity of cleaning the grease filter. 4. Proper Distance: Maintain the minimum distance between the supporting surface for the cooking equipment on the hob and the lowest part of the exhaust hood. The distance should be at least 50cm for electric cookers and 65cm for gas or mixed cookers, unless specified otherwise in the installation instructions. By following these steps, you can ensure proper ventilation when using the AEG X69163MD10 exhaust hood, which helps remove cooking fumes and keeps the air in your kitchen clean.

How do I properly clean the AEG X69163MD10 exhaust hood?

To properly clean the AEG X69163MD10 exhaust hood, follow these steps: 1. Grease Filter Cleaning: The grease filter should be cleaned at least once a month. You can clean it either by hand or in the dishwasher. If using the dishwasher, set it to a low temperature and a short cycle. Note that the grease filter may slightly discolor when washed in the dishwasher, but this does not affect its filtering capacity. 2. Non-Washable Charcoal Filter: The non-washable activated charcoal filter should be replaced at least every four months. It cannot be washed or regenerated. 3. External and Internal Cleaning: Clean the exhaust hood regularly, both internally and externally. Use a cloth dampened with neutral liquid detergent to clean the hood. Avoid using abrasive products or alcohol for cleaning. 4. Lamp Replacement: If you need to replace the lamp in the exhaust hood, refer to the Maintenance/Replacing lamps section of the manual for the specific lamp type to be used. Remember to observe these cleaning instructions to prevent fire risks and ensure the proper functioning of the exhaust hood. Regular maintenance and filter replacement are essential for optimal performance. Please note that these cleaning instructions are based on the information provided in the manual for the AEG X69163MD10 exhaust hood.

Why is the AEG X69163MD10 exhaust hood not aspirating fumes and vapors effectively?

The AEG X69163MD10 exhaust hood may not be effectively aspirating fumes and vapors due to the following reasons: 1. Clogged Grease Filter: If the grease filter is clogged with grease and debris, it can restrict the airflow and reduce the effectiveness of the exhaust hood. Clean the grease filter at least once a month using non-aggressive detergents, either by hand or in the dishwasher. 2. Saturation of Charcoal Filter: The non-washable activated charcoal filter can become saturated after prolonged use, affecting its ability to absorb odors. Replace the charcoal filter at least every four months to ensure optimal performance. 3. Insufficient Suction Power: Check if the exhaust hood is set to the appropriate suction speed. Use the high suction speed for concentrated kitchen vapors. It is recommended to switch on the hood for 5 minutes before cooking and leave it on during cooking and for about 15 minutes after cooking. 4. Blocked Air Ducts: Ensure that the air ducts and vents are not blocked or obstructed. Clear any obstructions that may hinder the airflow. 5. Incorrect Installation: Verify that the exhaust hood is installed correctly according to the provided instructions. Improper installation can affect the performance of the hood. Regular maintenance, including cleaning the filters and ensuring proper installation, is crucial for the effective operation of the AEG X69163MD10 exhaust hood.

What are the installation requirements for the AEG X69163MD10 exhaust hood?

To install the AEG X69163MD10 exhaust hood, follow these requirements: 1. Power Supply: Ensure that the mains power supply corresponds to the rating indicated on the plate located inside the hood. If the hood is provided with a plug, connect it to a socket in compliance with current regulations. If it is not fitted with a plug or the plug is not located in an accessible area, apply a double pole switch in accordance with standards to ensure complete disconnection of the mains. 2. Ventilation Regulations: It is important to closely follow the regulations provided by the local authorities regarding the technical and safety measures for fume discharging. The ducting system for the exhaust hood should not be connected to any existing ventilation system used for discharging exhaust fumes from appliances burning gas or other fuels. 3. Lamp Replacement: When replacing the lamp in the exhaust hood, use only the lamp type indicated in the Maintenance/Replacing lamps section of the manual. 4. Fixing Screws: Use the fixing screws supplied with the product for installation. If not supplied, purchase the correct type of screws. Ensure that the screws are of the correct length, as identified in the Installation Guide. It is important to install the exhaust hood according to these requirements to ensure safe and proper operation. If you have any doubts or need assistance, consult an authorized service assistance center or a qualified person.

How often should I replace the filters in the AEG X69163MD10 exhaust hood?

The filters in the AEG X69163MD10 exhaust hood should be replaced according to the following guidelines: 1. Grease Filter: The grease filter should be cleaned at least once a month using non-aggressive detergents. It can be cleaned either by hand or in the dishwasher. If using the dishwasher, set it to a low temperature and a short cycle. However, the grease filter may need to be replaced if it becomes damaged or excessively clogged. 2. Charcoal Filter: The non-washable activated charcoal filter should be replaced at least every four months. The saturation of the charcoal filter depends on the type of cooking and the regularity of cleaning the grease filter. It is important to note that the charcoal filter cannot be washed or regenerated. Regularly replacing the filters in the AEG X69163MD10 exhaust hood is essential to maintain its optimal performance and ensure effective removal of fumes and odors. Failure to replace the filters as recommended may result in reduced efficiency and increased fire risks.

Why is the lamp in the AEG X69163MD10 exhaust hood not working?

There could be several reasons why the lamp in the AEG X69163MD10 exhaust hood is not working. Here are the possible causes: 1. Power Disconnection: Check if the hood is properly connected to the mains power supply. Ensure that the power switch is turned on and that there is no power outage or tripped circuit breaker. 2. Lamp Failure: The lamp may have reached the end of its lifespan and needs to be replaced. Refer to the Maintenance/Replacing lamps section of the manual for the specific lamp type to be used. 3. Loose Connection: Inspect the lamp socket and wiring for any loose or disconnected connections. Ensure that the lamp is securely inserted into the socket. 4. Electrical Issue: If the lamp and connections are in good condition, there may be an electrical issue with the hood. In this case, it is recommended to consult an authorized service assistance center or a qualified person for further inspection and repair. Remember to always disconnect the hood from the electricity before touching the light bulbs for safety purposes. If you are unsure or need assistance, it is best to seek professional help to resolve the issue.

Is the manual of the AEG X69163MD10 available in English?

Yes, the manual of the AEG X69163MD10 is available in English .

Is your question not listed? Ask your question here

No results