Adtran Total Access 912 manual

Adtran Total Access 912
8.4 · 1
PDF manual
 · 2 pages
English
manualAdtran Total Access 912
Quick Start Guide, 61210916L1-13C, March 2006 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright © 2006 ADTRAN, All Rights Reserved
For more detailed documentation, visit us online at www.adtran.com.

Quick Start Guide

®

Total Access 912/916/924 P/N 1210912L1, 1210916L1, 1210924L1/L2

GETTING STARTED

Two configuration methods are available for your Total Access 900 Series:
Web-based GUI
AOS Command Line interface (CLI)
The GUI lets you configure the main unit settings and provides online guidance and explanations for
each setting. However, using the AOS CLI may be necessary for more advanced configurations.

ACCESS THE GUI

The Web-based GUI is an online configuration tool that allows you to easily configure and view the
main settings, as well as the status of your system.
1. Connect the Total Access 900 Series unit to your PC using the ETH 0/1 port on the rear panel
of the unit. The Total Access 900 Series units support auto MDI-MDIX crossover; therefore, a
straight-through cable can be used for this connection.
2. Configure your PC to obtain an IP address automatically (DHCP), or change the IP address of
your PC to 10.10.10.2. The default address for the Total Access 900 Series unit is 10.10.10.1.
3. Enter the unit’s IP address in your browser address field. The default IP address is 10.10.10.1.
4. You will then be prompted for the username and password. The default settings are admin and
password.
5. The initial GUI screen appears.
USING THE CONFIGURATION WIZARD
Once you have logged in, click on Config Wizard. Use the buttons at the bottom of the screen or
the menu at the top left to navigate the Config Wizard.
Use the system’s Config Wizard utility as an online configuration tool to set up basic (as well as
advanced) voice applications. The Config Wizard can easily walk you through system setup, voice
and data settings, and trunk and station configuration through a series of easy-to-answer questions.
At the end of the wizard, you can review your choices and accept them or make additional changes.
It is best to use the Config Wizard for new installations only because some
existing settings may be lost or reset when using this wizard.

ACCESS THE CLI

The following items are needed to connect to the Total Access 900 Series unit:
VT100 terminal or PC (with VT100 terminal emulation software)
Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate
interface for your terminal (or PC) on the other
1. Connect the DB-9 (male) connector of your serial cable to the CRAFT port on the rear panel of
the unit.
2. Connect the loose end of the serial cable to the VT100 terminal or PC (with terminal emulation
software).
3. Open a VT100 terminal session to the Total Access 900 Series unit using the following settings:
9600 baud, 8 data bits, no parity bits, 1 stop bit, and no flow control.
4. Press <Enter> to activate the ADTRAN Command Line Interface.
5. Enter enable at the > prompt, and enter the password when prompted. The default password is
password.
CONFIGURE THE UNITS IP ADDRESS
Follow these steps if you are not able to change the PC’s IP address in order to access the Web GUI.
Change the Total Access 900’s IP address to correspond with your network setup. If you are not sure
what IP address to assign, please contact your network administrator.
1. At the # prompt, enter config terminal.
2. At the (config)# prompt, enter interface eth 0/1 to access the Ethernet interface configuration
parameters.
3. Enter ip address 10.10.10.1
255.255.255.0 to assign an IP address to the Ethernet port using a
24-bit subnet mask.
4. Enter no shutdown to activate the interface to pass data.
5. Enter exit to exit the Ethernet interface commands and return to Global Configuration mode.
6. Enter exit to return to the Enable command security mode.
7. At the # prompt, enter copy running-config startup-config to save the current configuration to
memory.
8. Enter exit to close the configuration session.
The configuration parameters used in the examples outlined in this
document are for instructional purposes only. Please replace all underlined
entries (
example) with your specific parameters to configure your
application.

Manual

View the manual for the Adtran Total Access 912 here, for free. This manual comes under the category Not categorized and has been rated by 1 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the Adtran Total Access 912 or do you need help? Ask your question here

Need help?

Do you have a question about the Adtran Total Access 912 and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Adtran Total Access 912 owners to provide you with a good answer.

Number of questions: 0

Adtran Total Access 912 specifications

Below you will find the product specifications and the manual specifications of the Adtran Total Access 912.

General
Brand Adtran
Model Total Access 912 | 4212912L1
Product Not categorized
EAN 0607565025341, 6075650253414
Language English
Filetype Usermanual (PDF)
Protocols
Management protocols SIP, MGCP, SNMP v2/v3
Routing protocols IP
Supported protocols BGP, Multilink Frame Relay, OSPF, PPP, RIP (v1/v2), Multilink PPP, GRE, HDLC, IGMP V2, PAP /CHAP, Frame Relay, Multi-VRF
Security
Firewall security
Security algorithms SSH
Features
Interface T1 WAN, LAN, DigitalVoice, AnalogVoice
Voice codecs G.711,G.729a
Technical details
Platform Single T1/single Ethernet
Technical features VQM\nQoS\nNAT(1:1), NAPT(Many:1)
Network
Wi-Fi
Wireless connection
Full duplex
Security features antiDOS, ACL
Cabling technology 10/100Base-T(X)
Software
Bundled software AOS
Ports & interfaces
I/O ports 12 x FXS\nRJ-48C\nRJ-45\n
USB 2.0 ports quantity 0
Ethernet LAN (RJ-45) ports 1
Weight & dimensions
Dimensions (WxDxH) 436.88 x 215.9 x 43.688 mm
Weight 2494.75 g
Power
Power requirements 120, 60
Operational conditions
Operating temperature (T-T) 0 - 50 °C
Storage temperature (T-T) -40 - 70 °C
Operating altitude 0 - 3048 m
Management features
Performance management CLI, GUI, SNMP v2/v3, SYSLOG, elnet, Craft/Console Port, SSH, Ping, TraceRoute, NT, TCL
Design
Mounting type Rack mounting
Certification FCC Part 15, Class A\nFCC Part 68\nIndustry Canada CS03\nETL and Canadian ETL (C-ETL)\n
Performance
Internal memory 64 MB
Flash memory 32 MB
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Adtran Total Access 912 below.

Is your question not listed? Ask your question here

No results